Overclock.net › Forums › Intel › Intel Motherboards › Gigabyte GA-P35-DS3L Thread
New Posts  All Forums:Forum Nav:

Gigabyte GA-P35-DS3L Thread - Page 233

post #2321 of 4644
Hello!

I'm new to OC and new to this forum. This thread was very useful to me and I would like to extend my thanks!

I believe my system is now stable at about as high an OC as I am comfortable trying for now.

I've got an e3110 on this board and from what I've read, higher vcore can damage these CPU's without the heat being a factor. I've got the vcore set to 1.362, showing a useage of 1.332 in bios. I don't want it over 1.34, so that's as high as it goes.

I've ran Prime95 for 20 hours at 500x7.5
At 510x7.5, my game crashed 4 times last night within about 2 hours.

My scores in 3dMark are not very good because of my older vid card, which I did not upgrade yet. It was one of the parts I scavenged from my previous rig. Though I ran Super Pi 1m in 12 seconds. Is that good? LOL

I'm new to all this, but I feel I'm learning fairly quickly. I just downloaded Super Pi today as I saw it listed in the Sarge's chart. Not sure if those are 1m tests or not.. ?
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
post #2322 of 4644
Quote:
Originally Posted by (V)ayhe(V) View Post
Hello!

I'm new to OC and new to this forum. This thread was very useful to me and I would like to extend my thanks!

I believe my system is now stable at about as high an OC as I am comfortable trying for now.

I've got an e3110 on this board and from what I've read, higher vcore can damage these CPU's without the heat being a factor. I've got the vcore set to 1.362, showing a useage of 1.332 in bios. I don't want it over 1.34, so that's as high as it goes.

I've ran Prime95 for 20 hours at 500x7.5
At 510x7.5, my game crashed 4 times last night within about 2 hours.

My scores in 3dMark are not very good because of my older vid card, which I did not upgrade yet. It was one of the parts I scavenged from my previous rig. Though I ran Super Pi 1m in 12 seconds. Is that good? LOL

I'm new to all this, but I feel I'm learning fairly quickly. I just downloaded Super Pi today as I saw it listed in the Sarge's chart. Not sure if those are 1m tests or not.. ?
Which Prime test did you use. I can't imagine it being a stability problem with your cpu if it passed Prime95 for 20 hours.
Game System
(15 items)
 
  
CPUMotherboardGraphicsRAM
AMD FX 8320 ASUS Crosshair V Formula-Z Sapphire R9 290X 8GB Corsair Vengeance 
Hard DriveOptical DriveCoolingOS
Crucial BX100 SSD 1TB LG CDRW/DVDRW scythe fuma Windows 8.1 64 bit 
MonitorKeyboardPowerCase
27" Qnix QX2710 LED Blackwidow Ultimate Battlefield 3 Edition EVGA SuperNova 1300W Lian Li PC-80R 
MouseMouse PadAudio
Razer Deathadder Razer Exactmat Logitech G900 Headset  
  hide details  
Reply
Game System
(15 items)
 
  
CPUMotherboardGraphicsRAM
AMD FX 8320 ASUS Crosshair V Formula-Z Sapphire R9 290X 8GB Corsair Vengeance 
Hard DriveOptical DriveCoolingOS
Crucial BX100 SSD 1TB LG CDRW/DVDRW scythe fuma Windows 8.1 64 bit 
MonitorKeyboardPowerCase
27" Qnix QX2710 LED Blackwidow Ultimate Battlefield 3 Edition EVGA SuperNova 1300W Lian Li PC-80R 
MouseMouse PadAudio
Razer Deathadder Razer Exactmat Logitech G900 Headset  
  hide details  
Reply
post #2323 of 4644
Quote:
Originally Posted by (V)ayhe(V) View Post
Hello!

I'm new to OC and new to this forum. This thread was very useful to me and I would like to extend my thanks!

I believe my system is now stable at about as high an OC as I am comfortable trying for now.

I've got an e3110 on this board and from what I've read, higher vcore can damage these CPU's without the heat being a factor. I've got the vcore set to 1.362, showing a useage of 1.332 in bios. I don't want it over 1.34, so that's as high as it goes.

I've ran Prime95 for 20 hours at 500x7.5
At 510x7.5, my game crashed 4 times last night within about 2 hours.

My scores in 3dMark are not very good because of my older vid card, which I did not upgrade yet. It was one of the parts I scavenged from my previous rig. Though I ran Super Pi 1m in 12 seconds. Is that good? LOL

I'm new to all this, but I feel I'm learning fairly quickly. I just downloaded Super Pi today as I saw it listed in the Sarge's chart. Not sure if those are 1m tests or not.. ?
Ure asking the board to do 510 FSB ? hmm

I wouldnt use that 24/7.

What are ure voltages.

for 510FSB u need +0.3 NB (GMH) and +0.3 FSB.

at that FSB u use the 2.00 divider for 1:1 so memory at 820mhz.

Its not easy to do 500 FSB.

The best to run for prime 95/orthos is Large FFT.

Large FFT can crash within minutes it tests different parts of the CPUs Cache.

Also what are ure temps load and idle.
post #2324 of 4644
Just logged off my game (LOTRO), it crashed on me a few times in the past 2 hours, which I'm disappointed about since the prime test.

I run 2 instances of Prime95, one on each core. this 20 hour test was the blended test. I thought small FFT's were best to stress the CPU specifically? Again, I'm new to all this, so don't mind my ignorance.

I have +.1v to FSB.
My memory multi is 2.0
My temps are 36 idle, 55 load.
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
post #2325 of 4644
1.5 hours of Prime95 Large FFT's with no errors so far. I haven't changed any settings yet. I wish there was a test that would be as effective as LOTRO. I've successfully tested a few configs that failed to run LOTRO properly in the recent past. Is it perhaps because of the added load on PCI-e in addition to the OC settings?
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
post #2326 of 4644
Quote:
Originally Posted by (V)ayhe(V) View Post
Just logged off my game (LOTRO), it crashed on me a few times in the past 2 hours, which I'm disappointed about since the prime test.

I run 2 instances of Prime95, one on each core. this 20 hour test was the blended test. I thought small FFT's were best to stress the CPU specifically? Again, I'm new to all this, so don't mind my ignorance.

I have +.1v to FSB.
My memory multi is 2.0
My temps are 36 idle, 55 load.
What's your MCH voltage though? That's the first thing you want to increase when running with a high FSB clock.
 
Server
(3 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7-3540M Intel HD Graphics 4000 8GB G.SKILL Ripjaws DDR3 1600 Samsung 840 EVO 250GB SSD 
OSMonitorMouseAudio
Windows 10 Pro x64 14" at 1600x900 Logitech Anywhere Mouse MX FiiO E17 USB DAC amp 
CPUOSCase
i3-540 Debian 8 (Jessie) Cooler Master Elite 341 
  hide details  
Reply
 
Server
(3 items)
 
 
CPUGraphicsRAMHard Drive
Intel Core i7-3540M Intel HD Graphics 4000 8GB G.SKILL Ripjaws DDR3 1600 Samsung 840 EVO 250GB SSD 
OSMonitorMouseAudio
Windows 10 Pro x64 14" at 1600x900 Logitech Anywhere Mouse MX FiiO E17 USB DAC amp 
CPUOSCase
i3-540 Debian 8 (Jessie) Cooler Master Elite 341 
  hide details  
Reply
post #2327 of 4644
My current config has no boost to MCH.

I don't understand why I'm not getting any errors with Prime95. 3 hours now at large FFT's. When I do boost the MCH, how am I supposed to tell if it worked aside from playing LOTRO for a while? I'm open to suggestions.

I'll reboot now and up the MCH to +.1v, I'm not sure how high I want to go with stock MB cooling.

EDIT: I think I'll start a new thread so I'm not mucking up this one with my babbling.
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
My Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
Xeon e3110 @3.75GHz Gigabyte GA-P35-DS3L rev. 2 Sapphire HD2600XT Patriot Extreme DDR2-800 2x2GB 
Hard DriveOptical DriveOSMonitor
Barracuda 320GB SATA2 LG DVD ROM XP Pro SP2 BenQ MP721C 
PowerCaseMouse
Corsair CMPSU-620HX 620W Coolermaster CM 690 Mid Tower Black Logitech G5 
  hide details  
Reply
post #2328 of 4644
Quote:
Originally Posted by spooky View Post
With this mobo and a cooler master 590 case I'm having trouble getting the Power LED working. I've heard a couple people voice the same problem but no solution. For those of you who have this case or the 690 (i'm guessing they have the same pwr led lead) could you describe how you have yours hooked up to the mobo? .
On my centurion, the case power led would only glow with the faintest of light using the PWR pins on the motherboard. Attaching it to the MSG pins did the trick.
April 2008
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8400 (400x9 @1.25V) GA-P35-DS3L eVGA 8800GT 512MB 650MHz 2@G.skill F2-6400CL4-2GBPK 
Hard DriveOptical DriveOSPower
Seagate 500GB 7200.10 Lite-On LH-20A1S Windows XP Pro 64 SP2C Antec EA-650 
Case
Cooler Master Centurion 534+ 
  hide details  
Reply
April 2008
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8400 (400x9 @1.25V) GA-P35-DS3L eVGA 8800GT 512MB 650MHz 2@G.skill F2-6400CL4-2GBPK 
Hard DriveOptical DriveOSPower
Seagate 500GB 7200.10 Lite-On LH-20A1S Windows XP Pro 64 SP2C Antec EA-650 
Case
Cooler Master Centurion 534+ 
  hide details  
Reply
post #2329 of 4644
I currently have my FSB and MCH set to +.2. It has been this way for the past 2 weeks and I have not had any problems. In an antec 900 case, is it OK to leave it at this setting 24/7? Can I push one (or both) up to +.3 and still be OK or will I need extra cooling?
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel Q9450 @ 3.2 Gigabyte P35-DS3L EVGA 8800 GTS 512 2x2GB Mushkin 
Hard DriveOSMonitorKeyboard
640gb WD Caviar Windows Vista Premium 64 bit Dell 2407WFP-HC Logitech G15 (Old Style) 
PowerCaseMouse
Corsair 520HX Antec 900 Logitech M310 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel Q9450 @ 3.2 Gigabyte P35-DS3L EVGA 8800 GTS 512 2x2GB Mushkin 
Hard DriveOSMonitorKeyboard
640gb WD Caviar Windows Vista Premium 64 bit Dell 2407WFP-HC Logitech G15 (Old Style) 
PowerCaseMouse
Corsair 520HX Antec 900 Logitech M310 
  hide details  
Reply
post #2330 of 4644
Quote:
Originally Posted by onlycodered View Post
No problem. I was a bit worried too when my CPU fan was was only spinning at 350 RPM.
Thats about the same RPM mine was stuck at since buying this board 2 weeks ago..
I was just using the case fan header instead.
E8400 @ 4.0GHz
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8400 GA-P35-DS3L GeForce 8400GS CORSAIR XMS2 4GB 
Hard DriveOptical DriveOSPower
Maxtor and Seagate Lite-On and Samsung "Multi-booting" Xp-64, Xp-Pro, Vista Ultimate Lite Corsair TX750W 
Case
Antec SLK3700AMB 
  hide details  
Reply
E8400 @ 4.0GHz
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8400 GA-P35-DS3L GeForce 8400GS CORSAIR XMS2 4GB 
Hard DriveOptical DriveOSPower
Maxtor and Seagate Lite-On and Samsung "Multi-booting" Xp-64, Xp-Pro, Vista Ultimate Lite Corsair TX750W 
Case
Antec SLK3700AMB 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › Gigabyte GA-P35-DS3L Thread