Overclock.net › Forums › Intel › Intel CPUs › >> Q9300 Club <<
New Posts  All Forums:Forum Nav:

>> Q9300 Club << - Page 38

post #371 of 810
Anyone has an answer to the above question? I'm wondering the same thing. My Vdroop is so bad on my P5E. I have it set at 1.3 on bios and it turns out to be 1.24 under load in windows. To reach my goal of 3.5GHZ on Q9300, I might need to go over the 1.36 specified by Intel.

My system config is:

Q9300
P5E X38
4X1 GB Crucial Ballistix 8500
ASUS 4850
Arctic Cooling 7 Pro

Right now, I have the Q9300 clocked at 430X7.5 at 333 strap. Edit: No longer able to boot here.


I bumped up the FSB to 430, I can't pass Prime95 further than this.
Ai Overclock Tuner : Manual
CPU Ratio Control : Manual
- Ratio CMOS Setting : 7.5
FSB Frequency : 430
FSB Strap to North Bridge : 333
PCI-E Frequency: 100
DRAM Frequency: 1033
DRAM Command Rate : 2t
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: AUTO
Ai Clock Twister : AUTO
Transaction Booster : AUTO
Boost Level :0
CPU Voltage : 1.300(highest I've tried)
CPU PLL Voltage : AUTO
North Bridge Voltage : AUTO
DRAM Voltage : 2.2v
FSB Termination Voltage : AUTO
South Bridge Voltage : AUTO
Loadline Calibration : Enabled
CPU GTL Reference : .AUTO
North Bridge GTL Reference : AUTO
SB 1.5V Voltage : AUTO

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

CPUID 1.275 idle and 1.24V load on CPU-Z.

When I try to increase Nbridge voltage or PLL from stock, I can't boot at all. Maybe I'm doing this wrong. I read in a review once that this board got up to 500FSB on a quad without increasing any other voltages except CPU.


I helped my friend get to 3.5GHZ on a P35 DS3R before, so I'm hoping to get the same or even better.

Any help would be appreciated.
Edited by rom0n - 7/21/08 at 3:06pm
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
post #372 of 810
can anyone help me and rom0n please?
I like I like :)
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.4 P5Q-E Diamond HD 4850 4GB PC2-8500 Mushkin Ascent 
Hard DriveOptical DriveOSMonitor
WD 640GB Pioneer 215 Vista Ultimate 64 Bit Samsung 22" 2253 
PowerCaseMouseMouse Pad
PC & Cooling 750W CM Stacker 832 G5 SteelSeries Qck 
  hide details  
Reply
I like I like :)
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.4 P5Q-E Diamond HD 4850 4GB PC2-8500 Mushkin Ascent 
Hard DriveOptical DriveOSMonitor
WD 640GB Pioneer 215 Vista Ultimate 64 Bit Samsung 22" 2253 
PowerCaseMouseMouse Pad
PC & Cooling 750W CM Stacker 832 G5 SteelSeries Qck 
  hide details  
Reply
post #373 of 810
Hey YellowBUM, what's your voltage settings?

Mine is:
I bumped up the FSB to 430, I can't pass Prime95 further than this.
Ai Overclock Tuner : Manual
CPU Ratio Control : Manual
- Ratio CMOS Setting : 7.5
FSB Frequency : 430
FSB Strap to North Bridge : 333
PCI-E Frequency: 100
DRAM Frequency: 1033
DRAM Command Rate : 2t
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: AUTO
Ai Clock Twister : AUTO
Transaction Booster : AUTO
Boost Level :0
CPU Voltage : 1.300(highest I've tried)
CPU PLL Voltage : 1.56
North Bridge Voltage : 1.45
DRAM Voltage : 2.2v
FSB Termination Voltage : 1.32
South Bridge Voltage : AUTO
Loadline Calibration : Disabled
CPU GTL Reference : .0.63X
North Bridge GTL Reference : 0.67X
SB 1.5V Voltage : AUTO

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

CPUID 1.275 idle and 1.24V load on CPU-Z.
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
post #374 of 810
Damn, i think i just got mine to work Romon.

I'm running at 3.4 GHz right now, going to try to see if I can get 3.5Ghz.

my specs are in my sig.

My settings are:

Ai Overclock Tuner : Manual
CPU Ratio Control : Manual
- Ratio CMOS Setting : 7.5
FSB Frequency : 454
FSB Strap to North Bridge : 333
PCI-E Frequency: 100
DRAM Frequency: 1091
DRAM Command Rate : 2t
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: Disabled
Ai Clock Twister : Lighter
Transaction Booster : Manual
Boost Level :09
CPU Voltage : 1.24375(highest I've tried)
CPU PLL Voltage : Auto
North Bridge Voltage : 1.36
DRAM Voltage : 2.1v
FSB Termination Voltage : 1.36
South Bridge Voltage : AUTO
Loadline Calibration : Enabled
CPU GTL Reference : .0.63X
North Bridge GTL Reference : 0.67X
SB 1.5V Voltage : AUTO

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

MY Vcore at idle from CPU-Z is 1.208V and on Load it's at 1.216V or 1.224V
Check my settings for the Enable/Disable options, i think that's what's holding you back.
Gonna try and push 3.5, I'll get back to you with what I've got.
I like I like :)
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.4 P5Q-E Diamond HD 4850 4GB PC2-8500 Mushkin Ascent 
Hard DriveOptical DriveOSMonitor
WD 640GB Pioneer 215 Vista Ultimate 64 Bit Samsung 22" 2253 
PowerCaseMouseMouse Pad
PC & Cooling 750W CM Stacker 832 G5 SteelSeries Qck 
  hide details  
Reply
I like I like :)
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.4 P5Q-E Diamond HD 4850 4GB PC2-8500 Mushkin Ascent 
Hard DriveOptical DriveOSMonitor
WD 640GB Pioneer 215 Vista Ultimate 64 Bit Samsung 22" 2253 
PowerCaseMouseMouse Pad
PC & Cooling 750W CM Stacker 832 G5 SteelSeries Qck 
  hide details  
Reply
post #375 of 810
Hi all.

Have recently bought a new system and decided to try some OC. Invested in a Xigmatex hdt-s1283 cooler and started to explore the dreaded bios, hehe.



Edited by runquest - 7/22/08 at 3:20am
tweak
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3,5 GHz ASUS P5E X38 (w/pencil mod.) XFX GeForce 8800 GT 512Mb Alpha Dog Corsair Dominator 8500 2x2Gb (micron) 
Hard DriveOptical DriveOSMonitor
2x Barracuda 250GB / 2x Caviar GP 500GB in RAID 0 Samsung (something) Windows Vista Ultimate 64 Samsung SyncMaster 226BW 
KeyboardPowerCaseMouse
Logitech Deluxe 250 Corsair Powersupply 550W Antec Nine Hundred (modded) Logitech G7 
Mouse Pad
green with bubbles 
  hide details  
Reply
tweak
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3,5 GHz ASUS P5E X38 (w/pencil mod.) XFX GeForce 8800 GT 512Mb Alpha Dog Corsair Dominator 8500 2x2Gb (micron) 
Hard DriveOptical DriveOSMonitor
2x Barracuda 250GB / 2x Caviar GP 500GB in RAID 0 Samsung (something) Windows Vista Ultimate 64 Samsung SyncMaster 226BW 
KeyboardPowerCaseMouse
Logitech Deluxe 250 Corsair Powersupply 550W Antec Nine Hundred (modded) Logitech G7 
Mouse Pad
green with bubbles 
  hide details  
Reply
post #376 of 810
Hey runquest. Let's exchange OC data as we both have the same mobo and CPU.
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
post #377 of 810
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
post #378 of 810
WoW so many new members while I was away.
Nice to see you all helping each other get higher speeds.
If you see that your stats are not right let me know, and as for VCore I am looking for what you have your BIOS set to NOT what cpu-z says it is at.
I got mine to 3.3Ghz @ 1.3v stable but I'm still running at 3.0Ghz to save a little life.
Keep up the great work... :-D
Remnant v2
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.0Ghz 1.3v EVGA 780i (P10) EVGA GTX 465FTW 4x1GB Corsair Dominator DDR2-8500 (5-5-5-15 :1067) 
Hard DriveOptical DriveOSMonitor
2x 500GB WD Black RAID+0 Samsung DVD-R SATA Win7 x64 Ultimate // Ubuntu 8.10 x64 Dell 2005FPW LCD 
KeyboardPowerCaseMouse
MS ABS MAJESTY 1100W Cooler Master COSMOS 1000 MS 
Mouse Pad
Belkin 
  hide details  
Reply
Remnant v2
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.0Ghz 1.3v EVGA 780i (P10) EVGA GTX 465FTW 4x1GB Corsair Dominator DDR2-8500 (5-5-5-15 :1067) 
Hard DriveOptical DriveOSMonitor
2x 500GB WD Black RAID+0 Samsung DVD-R SATA Win7 x64 Ultimate // Ubuntu 8.10 x64 Dell 2005FPW LCD 
KeyboardPowerCaseMouse
MS ABS MAJESTY 1100W Cooler Master COSMOS 1000 MS 
Mouse Pad
Belkin 
  hide details  
Reply
post #379 of 810
Quote:
Originally Posted by teK0wnzU View Post
WoW so many new members while I was away.
Nice to see you all helping each other get higher speeds.
If you see that your stats are not right let me know, and as for VCore I am looking for what you have your BIOS set to NOT what cpu-z says it is at.
I got mine to 3.3Ghz @ 1.3v stable but I'm still running at 3.0Ghz to save a little life.
Keep up the great work... :-D
Can I get your configuration for 3.3Ghz? I tried many voltage increase to my Northbridge, PLL, RAM, but I cannot get higher than my this config:

Ai Overclock Tuner : Manual
CPU Ratio Control : Manual
- Ratio CMOS Setting : 7.5
FSB Frequency : 430
FSB Strap to North Bridge : 333
PCI-E Frequency: 100
DRAM Frequency: 860
DRAM Command Rate : 2t
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: Disabled
Ai Clock Twister : Light
Transaction Booster : Disabled
Relax Level :0
CPU Voltage : 1.300
CPU PLL Voltage : 1.56
North Bridge Voltage : 1.45
DRAM Voltage : 2.2v
FSB Termination Voltage : 1.32
South Bridge Voltage : AUTO
Loadline Calibration : Disabled
CPU GTL Reference : .0.63X
North Bridge GTL Reference : 0.67X
SB 1.5V Voltage : AUTO

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

Thanks.
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 P5E ASUS EAH 4850 MB 4X1 GB Crucial Tracers 8500 
Hard DriveOptical DriveMonitorPower
Samsung F1 1TB BenQ Dell 1907F 500W Earth Watts 
Case
Sonata III 
  hide details  
Reply
post #380 of 810
Before I get into all my settings, what is your cpu's VID? the higher it is the more volts it will take to OC it. mine is 1.1875v so I can OC more with less votls that if it was 1.21v.
Remnant v2
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.0Ghz 1.3v EVGA 780i (P10) EVGA GTX 465FTW 4x1GB Corsair Dominator DDR2-8500 (5-5-5-15 :1067) 
Hard DriveOptical DriveOSMonitor
2x 500GB WD Black RAID+0 Samsung DVD-R SATA Win7 x64 Ultimate // Ubuntu 8.10 x64 Dell 2005FPW LCD 
KeyboardPowerCaseMouse
MS ABS MAJESTY 1100W Cooler Master COSMOS 1000 MS 
Mouse Pad
Belkin 
  hide details  
Reply
Remnant v2
(13 items)
 
  
CPUMotherboardGraphicsRAM
Q9300 @ 3.0Ghz 1.3v EVGA 780i (P10) EVGA GTX 465FTW 4x1GB Corsair Dominator DDR2-8500 (5-5-5-15 :1067) 
Hard DriveOptical DriveOSMonitor
2x 500GB WD Black RAID+0 Samsung DVD-R SATA Win7 x64 Ultimate // Ubuntu 8.10 x64 Dell 2005FPW LCD 
KeyboardPowerCaseMouse
MS ABS MAJESTY 1100W Cooler Master COSMOS 1000 MS 
Mouse Pad
Belkin 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
Overclock.net › Forums › Intel › Intel CPUs › >> Q9300 Club <<