Overclock.net › Forums › Cooling › Water Cooling › [PROJECT] It's finally done!
New Posts  All Forums:Forum Nav:

[PROJECT] It's finally done! - Page 2

post #11 of 13
Omg. Nice.
VICE
(19 items)
 
  
CPUMotherboardGraphicsRAM
AMD Ryzen 5 1600 ASUS ROG STRIX B350-F GAMING ASUS ROG Strix RX 560 4g OC CORSAIR Vengeance LPX 16GB DDR4-3000 
Hard DriveHard DriveHard DriveCooling
Corsair Force MP500 Series M.2 SSD 240GB  256gb Kingston HyperX Savage SSD 240gb Sandisk Extreme SSD  Barrow LTYK3A-04 
CoolingCoolingCoolingOS
EK 480mm Radiator 2x XSPC Photon 170 D5 Pump/Res Combos 360mm Swiftech Radiator  Windows 10 64-Bit 
MonitorKeyboardPowerCase
Dell UltraSharp U2412M Custom WASD mechanical Evga 750w SuperNOVA G2 CaseLabs Merlin SM8 
MouseMouse PadAudio
CM Storm Xornet ROG Asus SupremeFX Realtek 1220 
  hide details  
Reply
VICE
(19 items)
 
  
CPUMotherboardGraphicsRAM
AMD Ryzen 5 1600 ASUS ROG STRIX B350-F GAMING ASUS ROG Strix RX 560 4g OC CORSAIR Vengeance LPX 16GB DDR4-3000 
Hard DriveHard DriveHard DriveCooling
Corsair Force MP500 Series M.2 SSD 240GB  256gb Kingston HyperX Savage SSD 240gb Sandisk Extreme SSD  Barrow LTYK3A-04 
CoolingCoolingCoolingOS
EK 480mm Radiator 2x XSPC Photon 170 D5 Pump/Res Combos 360mm Swiftech Radiator  Windows 10 64-Bit 
MonitorKeyboardPowerCase
Dell UltraSharp U2412M Custom WASD mechanical Evga 750w SuperNOVA G2 CaseLabs Merlin SM8 
MouseMouse PadAudio
CM Storm Xornet ROG Asus SupremeFX Realtek 1220 
  hide details  
Reply
post #12 of 13
Thread Starter 
Thanks for the good comments guys. I really appreciate it

I'm glad my first WC project turned out a success... eventually.

Quote:
Originally Posted by this n00b again View Post
JOB well done!


in the final pics i see OCZ ram not the kingston ram with TR heatsinks.

i know you noted it at the end, but what happened?
Well the 790i only supports DDR3. And I'm stuck with SLI and don't want to get 780i again so had to buy new RAM too. The kingston's and the 780i are going to be sold soon.

Quote:
Originally Posted by ira-k View Post
Very nice......Thanks for all the pic's...I really like your rad mounts...It looks like your rad fans are in a push? If they are you might want to try a pull with them, and shrouds will also help a little...You are well enough over-radded it might not even make much difference...
Ambient is high here. Temps I'm getting right now are like this:

Board: 40C
CPU: 45-60C idle-load (stock) / 45-65C (3.6GHz)
NB/SB: 40-45C (FSB 1066 or 1600, doesn't change)
GPUs: 40-50C (stock)

CPU idle is a bit high (I guess because of the chipset block keeping it warm) but doesn't go above 60C at full load with prime running small FFT's. And I also think this loop is still bleeding so will see if it gets better over time.

I will try to make a shroud and will try them in pull config sometime tho. Thanks for the hints

Quote:
Originally Posted by tindolos View Post
Did you say your board was dead with a FF error?

On my 680i board, FF means "fully functional"
Actually the board goes straight to FF, no video no nothing, not test codes. Something went really wrong with it and I believe a certain power regulator got fried somehow because it was getting hot when the PSU was connected and powered on.
PC2
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7-2600k MSI Big Bang Marshal EVGA GTX580 SLI Mushkin Blackline 8GB 
Hard DriveOSMonitorPower
Intel X25M 80GB Raid0 Windows 7 64-bit Enterprise NEC 3090WQXi Corsair HX1000 
CaseMouse
HAF X Microsoft Habu 
  hide details  
Reply
PC2
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7-2600k MSI Big Bang Marshal EVGA GTX580 SLI Mushkin Blackline 8GB 
Hard DriveOSMonitorPower
Intel X25M 80GB Raid0 Windows 7 64-bit Enterprise NEC 3090WQXi Corsair HX1000 
CaseMouse
HAF X Microsoft Habu 
  hide details  
Reply
post #13 of 13
Quote:
CPU idle is a bit high (I guess because of the chipset block keeping it warm) but doesn't go above 60C at full load with prime running small FFT's. And I also think this loop is still bleeding so will see if it gets better over time.
The higher your v-core is with WC'ing the higher your idle temp's will be, no biggie, it just shows you have a higher v-core...A HSF will keep your idle lower but wont hold you load temp's like WC will...You'll have less of a delta between idle and load with WC'ing...

Nice temp's......A sure sign of a job well done!!! It will settle in more the next few days, temp's should drop a little...I always like to do at least 4 or 5 re-mounts with a new block and see what kind of temp's I should be getting with it...I let each one burn in a week or two, then try another...Then I'll try to work it back to my lowest temp, which is hard sometimes, every now and then I'll get that perfect mount and not be able to work back down to it...
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8600 4545Mhz*9 w/1.29V DFI DK P45 XFX 8800 GS D9GKX & D9GMH 
Hard DriveOptical DriveOSPower
2x Seagate 160 Perp. RD-1 2x Asus Vista Premium Corsair HX 620 
Case
Open Bench 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
E8600 4545Mhz*9 w/1.29V DFI DK P45 XFX 8800 GS D9GKX & D9GMH 
Hard DriveOptical DriveOSPower
2x Seagate 160 Perp. RD-1 2x Asus Vista Premium Corsair HX 620 
Case
Open Bench 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › [PROJECT] It's finally done!