Overclock.net › Forums › AMD › AMD Motherboards › [Official] ASUS M2N-SLI and M2N32-SLI Club!
New Posts  All Forums:Forum Nav:

[Official] ASUS M2N-SLI and M2N32-SLI Club! - Page 1040

post #10391 of 11269
Thanks for the reply I will be having a look at the but I have another question aswell, i got this board about two months ago and on my old Abit board my CPU temp was min@ 35 AND Max@ 60 and when i got the new board i have now my cpu idle's @ 60 and almost to 90 at full load. I have added new paste twice already. first with standerd paste and second (which is on now) with arctic cool paste. I am using open hardware monitor for temp readings. i just cant understand why it would be doing this when all i have done is change the mobo (and obviasly add another graphics card). Could it be the heatpipes around the CPU? o and i am using water cooling Antec Kuhler H2O 620.
post #10392 of 11269
You tend to lose a lot of airflow over the MB when using those types of coolers.
Did you get a squirrel cage fan with the board? if so stick it on and plug it to the chipset fan header.This will help MB temps,not cpu temps.
386

How is the case airflow?Is the khuler rad setup as intake or exhaust?
What case are you using?

But it looks to me like either to much or not enough TIM.


Gyro
My System
(14 items)
 
  
CPUMotherboardGraphicsGraphics
AMD Ph IIx4 955 @ 3.2 Asus M2N32-sli dlx Asus GTX 460 1gb DirectCU MSI GTX 460 1gb Cyclone 
RAMHard DriveOptical DriveOS
2x2gb OCZ ddr2 1066 plats seagate 320gb sata lg supermulti dvd WIN 7 64 
MonitorKeyboardPowerCase
acer p221w ms SS ST75F-P 750w CM 690modded w/KazeMaster pro 
Mouse
ms intellimouse explorer3.0 
  hide details  
Reply
My System
(14 items)
 
  
CPUMotherboardGraphicsGraphics
AMD Ph IIx4 955 @ 3.2 Asus M2N32-sli dlx Asus GTX 460 1gb DirectCU MSI GTX 460 1gb Cyclone 
RAMHard DriveOptical DriveOS
2x2gb OCZ ddr2 1066 plats seagate 320gb sata lg supermulti dvd WIN 7 64 
MonitorKeyboardPowerCase
acer p221w ms SS ST75F-P 750w CM 690modded w/KazeMaster pro 
Mouse
ms intellimouse explorer3.0 
  hide details  
Reply
post #10393 of 11269
I did get the squirrel cage fan with the board but that is not on the header as it wont fit due to the fan on my radiator over lapping the header heat pips (if that’s what u mean).

Regarding my airflow i have one 120mm fan intake at the front of the case, 120mm intake on my side panel on both my graphics cards, 80mm fan outtake of my GPU heat on the middle front of my case and two 120mm fans on my radiator with a push-pull config outtaking heat.
and the case i am using is an NZXT M59.

and what do u mean by "TIM"?
post #10394 of 11269
TIM=Thermal Interface Material or thermal paste.

Download this http://www.cpuid.com/softwares/hwmonitor.html and post a screenshot so we can see the overall temps.


Gyro
My System
(14 items)
 
  
CPUMotherboardGraphicsGraphics
AMD Ph IIx4 955 @ 3.2 Asus M2N32-sli dlx Asus GTX 460 1gb DirectCU MSI GTX 460 1gb Cyclone 
RAMHard DriveOptical DriveOS
2x2gb OCZ ddr2 1066 plats seagate 320gb sata lg supermulti dvd WIN 7 64 
MonitorKeyboardPowerCase
acer p221w ms SS ST75F-P 750w CM 690modded w/KazeMaster pro 
Mouse
ms intellimouse explorer3.0 
  hide details  
Reply
My System
(14 items)
 
  
CPUMotherboardGraphicsGraphics
AMD Ph IIx4 955 @ 3.2 Asus M2N32-sli dlx Asus GTX 460 1gb DirectCU MSI GTX 460 1gb Cyclone 
RAMHard DriveOptical DriveOS
2x2gb OCZ ddr2 1066 plats seagate 320gb sata lg supermulti dvd WIN 7 64 
MonitorKeyboardPowerCase
acer p221w ms SS ST75F-P 750w CM 690modded w/KazeMaster pro 
Mouse
ms intellimouse explorer3.0 
  hide details  
Reply
post #10395 of 11269
Quote:
Originally Posted by shadowalker View Post

I did get the squirrel cage fan with the board but that is not on the header as it wont fit due to the fan on my radiator over lapping the header heat pips (if that’s what u mean).
Regarding my airflow i have one 120mm fan intake at the front of the case, 120mm intake on my side panel on both my graphics cards, 80mm fan outtake of my GPU heat on the middle front of my case and two 120mm fans on my radiator with a push-pull config outtaking heat.
and the case i am using is an NZXT M59.
and what do u mean by "TIM"?

you can also put the squirrel cage cooler on the other heat pipe thins above the pcie slot as well i actually am using 2 squirrel cages at the moment and it actually pulls the heat away from my video card as well thumb.gif
Dust Collector
(15 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II X4 965 4.0 Ghz (HDZ965FBK4DGM) ASUS M2N32 SLI-Deluxe SPARKLE Calibre Series GeForce GTX 580 2x2gb gskill F2-6400CL5D-4GBPQ 
Hard DriveHard DriveOptical DriveCooling
westdigital black WDC WD5001AALS-00E3A (465 GB) samsung f3r HE103SJ (931 GB) TSSTcorp CD/DVDW SH-S183L Noctua NH-D14 
OSMonitorKeyboardPower
Microshaft Winblows 7.2 x64 (Daz) 19inch Acer AL1916 compaq coolermaster silentpro 700w 
CaseMouseAudio
antec 1200 logitech onboard 
  hide details  
Reply
Dust Collector
(15 items)
 
  
CPUMotherboardGraphicsRAM
AMD Phenom II X4 965 4.0 Ghz (HDZ965FBK4DGM) ASUS M2N32 SLI-Deluxe SPARKLE Calibre Series GeForce GTX 580 2x2gb gskill F2-6400CL5D-4GBPQ 
Hard DriveHard DriveOptical DriveCooling
westdigital black WDC WD5001AALS-00E3A (465 GB) samsung f3r HE103SJ (931 GB) TSSTcorp CD/DVDW SH-S183L Noctua NH-D14 
OSMonitorKeyboardPower
Microshaft Winblows 7.2 x64 (Daz) 19inch Acer AL1916 compaq coolermaster silentpro 700w 
CaseMouseAudio
antec 1200 logitech onboard 
  hide details  
Reply
post #10396 of 11269
Hi All, have not been here for a while.
I've been running my M2N32-SLI Deluxe with a Phenom II 945 for a lil while now.
It's been running on 4GB of Corsair (2*2048MB) PN:CM2X2048-6400C5 in DIMM Slots A1 and A2.
Recently one of the memory stick died and system wouldn't post so I ran it with only 2GB in DIMM slot A1 for a few days.

So this brought me to do a lil upgrade and went ahead and got me two kits of G.SKILL PN: F2-8500CL5D-4GBPK to bring the system to a total of 8GB with all mem slots populated. Had to do a couple tweaks in BIOS, nothing mayor. I'm running Windows 7 Ultima x64 by the way.

The thing is that I've always had a problem with this MB when trying to run memory in slots B1, or B2. Below are the different ways I've tried to get this thing going.

Single Slot Populated
A1: POST OK, Windows Boots and Runs OK.
B1: NO POST, NO BEEP CODES, NOTHING.
A2: POST OK, Windows Boots and Runs OK.
B2: NO POST, NO BEEP CODES, NOTHING.

Two Slots Populated
A1+B1: NO POST, NO BEEP CODES, NOTHING.
A2+B2: NO POST, NO BEEP CODES, NOTHING.
B1+B2: NO POST, NO BEEP CODES, NOTHING.
A1+A2: POST OK, Windows Boots and Runs OK.

I have not been able to get it working, ever. I'm just trying to figure out if anyone can shed some light into what might be the problem or if it's simply that my motherboard had CH_B DIMM slots dead. I've tried every possible way with just a stick in slot B1 for example to get it working and it will never POST. Resetting BIOS, presetting memory timmings and all that stuff, but I'm stuck with 4GB I guess unless anyone has any info/idea that can help me out.
BlackHawk
(15 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 945 ASUS SABERTOOTH 990FX/GEN3 R2.0 EVGA 550 Ti Crucial Ballistix 8GB (2 x 4GB) DDR3 SDRAM 
Hard DriveHard DriveOptical DriveCooling
Western Digital 160GB 10K RPM (OS) WESTERN DIGITAL 2TB NAS ASUS 24X SATA DVD Burner Zalman 
OSMonitorKeyboardPower
Windows 8 Pro x64 Sony 3D PS3 24" LCD x2 Logitech Wireless S510 Ultra 550W 
CaseMouse
Thermaltake Shark Black Logitech Wireless 
  hide details  
Reply
BlackHawk
(15 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 945 ASUS SABERTOOTH 990FX/GEN3 R2.0 EVGA 550 Ti Crucial Ballistix 8GB (2 x 4GB) DDR3 SDRAM 
Hard DriveHard DriveOptical DriveCooling
Western Digital 160GB 10K RPM (OS) WESTERN DIGITAL 2TB NAS ASUS 24X SATA DVD Burner Zalman 
OSMonitorKeyboardPower
Windows 8 Pro x64 Sony 3D PS3 24" LCD x2 Logitech Wireless S510 Ultra 550W 
CaseMouse
Thermaltake Shark Black Logitech Wireless 
  hide details  
Reply
post #10397 of 11269
Quote:
Originally Posted by drkidd22 View Post

Hi All, have not been here for a while.
I've been running my M2N32-SLI Deluxe with a Phenom II 945 for a lil while now.
It's been running on 4GB of Corsair (2*2048MB) PN:CM2X2048-6400C5 in DIMM Slots A1 and A2.
Recently one of the memory stick died and system wouldn't post so I ran it with only 2GB in DIMM slot A1 for a few days.
So this brought me to do a lil upgrade and went ahead and got me two kits of G.SKILL PN: F2-8500CL5D-4GBPK to bring the system to a total of 8GB with all mem slots populated. Had to do a couple tweaks in BIOS, nothing mayor. I'm running Windows 7 Ultima x64 by the way.
The thing is that I've always had a problem with this MB when trying to run memory in slots B1, or B2. Below are the different ways I've tried to get this thing going.
Single Slot Populated
A1: POST OK, Windows Boots and Runs OK.
B1: NO POST, NO BEEP CODES, NOTHING.
A2: POST OK, Windows Boots and Runs OK.
B2: NO POST, NO BEEP CODES, NOTHING.
Two Slots Populated
A1+B1: NO POST, NO BEEP CODES, NOTHING.
A2+B2: NO POST, NO BEEP CODES, NOTHING.
B1+B2: NO POST, NO BEEP CODES, NOTHING.
A1+A2: POST OK, Windows Boots and Runs OK.
I have not been able to get it working, ever. I'm just trying to figure out if anyone can shed some light into what might be the problem or if it's simply that my motherboard had CH_B DIMM slots dead. I've tried every possible way with just a stick in slot B1 for example to get it working and it will never POST. Resetting BIOS, presetting memory timmings and all that stuff, but I'm stuck with 4GB I guess unless anyone has any info/idea that can help me out.

I don't have any first hand experience with 1066 in our bards but. I think I know what's going on here. assuming that B1+B2 worked just fine prior to upgrade, 1066 RAM is limited to only 2 slots on our boards. If you want to get all your slots populated, you will have to have A1 populated to get into the BIOS. Once you are in there, set the ram to operate at 800 and set your DIMM voltage to it's correct operating settings. After you set this up, you should be able to boot with all your ram in the motherboard assuming that you don't have any bad slots. If everything goes well, you can actually OC your ram up towards 1066.
My 5year old Mobo
(14 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 970BE ASUS M2N32 SLI-Deluxe EVGA 570 GTX SC Edition 4GB Corsair XMS DDR2 800 
Hard DriveOptical DriveCoolingOS
160gb Intel 320 SSD LG Super multi combo Dirve XSPC Raystorm  Windows Seven 
MonitorKeyboardPowerCase
ASUS VW266H Black 25.5" 2ms Logitech G15 (First Gen) Enermax Infinity 720w NZXT Switch 810 
Mouse
Logitech G5 
  hide details  
Reply
My 5year old Mobo
(14 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 970BE ASUS M2N32 SLI-Deluxe EVGA 570 GTX SC Edition 4GB Corsair XMS DDR2 800 
Hard DriveOptical DriveCoolingOS
160gb Intel 320 SSD LG Super multi combo Dirve XSPC Raystorm  Windows Seven 
MonitorKeyboardPowerCase
ASUS VW266H Black 25.5" 2ms Logitech G15 (First Gen) Enermax Infinity 720w NZXT Switch 810 
Mouse
Logitech G5 
  hide details  
Reply
post #10398 of 11269
Nah, It's not only with the 1066 that I see this problem.
I also have four 512MB Corsair DDR2 800MHz (CM2X512A-6400) and the system won't POST with those as well when all slots are populated.
I have done the same testing with the 512MB sticks and with same result. The MB won't even POST with the good 2048MB Corsair Stick I have when it's installed in slot B1 by itself.

Here is my CPU-Z Validation.
2434253.png
Edited by drkidd22 - 7/9/12 at 7:34pm
BlackHawk
(15 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 945 ASUS SABERTOOTH 990FX/GEN3 R2.0 EVGA 550 Ti Crucial Ballistix 8GB (2 x 4GB) DDR3 SDRAM 
Hard DriveHard DriveOptical DriveCooling
Western Digital 160GB 10K RPM (OS) WESTERN DIGITAL 2TB NAS ASUS 24X SATA DVD Burner Zalman 
OSMonitorKeyboardPower
Windows 8 Pro x64 Sony 3D PS3 24" LCD x2 Logitech Wireless S510 Ultra 550W 
CaseMouse
Thermaltake Shark Black Logitech Wireless 
  hide details  
Reply
BlackHawk
(15 items)
 
  
CPUMotherboardGraphicsRAM
Phenom II X4 945 ASUS SABERTOOTH 990FX/GEN3 R2.0 EVGA 550 Ti Crucial Ballistix 8GB (2 x 4GB) DDR3 SDRAM 
Hard DriveHard DriveOptical DriveCooling
Western Digital 160GB 10K RPM (OS) WESTERN DIGITAL 2TB NAS ASUS 24X SATA DVD Burner Zalman 
OSMonitorKeyboardPower
Windows 8 Pro x64 Sony 3D PS3 24" LCD x2 Logitech Wireless S510 Ultra 550W 
CaseMouse
Thermaltake Shark Black Logitech Wireless 
  hide details  
Reply
post #10399 of 11269
Quote:
Originally Posted by N2Gaming View Post

Hey from one M2N lov3r to another I will tell you this.
Try another OS install w/new drivers. Sounds to me like Malware or Virus shinanagans at it's best.

Lol I was pretty stupid not to format the drive straight away.

It now works wonders, even with the old RAM smile.gif

I'm currently looking for a cheap e-series processor, as I need something that will eat less power than this Opteron... 103W TDP O__O
   
AGP bencher
(14 items)
 
CPUMotherboardGraphicsRAM
Phenom X6 1055T ASUS M4A89GTD Pro/USB3 Sapphire HD 6950 2GB Kingston HyperX DDR3-2000 
Hard DriveHard DriveCoolingCooling
Seagate 7200.12 Samsung SpinPoint F3 EK Supreme HF EK CoolStream XT360 
CoolingCoolingOSMonitor
Alpahcool Coolplex Pro 10LT Phobya DC12-400 Windows 7 Ultimate & Fedora 17 LG IPS235V 
MonitorKeyboardPowerCase
LG E2250V Logitech G11 NOX Sonar 780W (Kingwin 750W 80+) Lian Li PC-A05NB 
MouseAudio
Logitech G9 ASUS Xonar DX 
CPUMotherboardGraphicsRAM
AMD A10-5700 Gigabyte F2A75M-HD2 Radeon 7660D G.SKILL Ares 2133 CL9 
Hard DriveCoolingOSOS
Hitachi 5K750 Noctua NH-L9a Fedora 18 Windows 7 x64 
MonitorKeyboardPowerCase
AUO B156HW01 Logitech MK220  PicoPSU-80-WI-25V AIO Aluminium Handmade 
Other
TP-LINK 150 N/G/B 
CPUCPUCPUMotherboard
Core2Duo E6400 Core2Quad Q6600 Pentium Dual Core E5200 AsRock 4COREDUAL-SATA2 R2.0 
GraphicsRAMHard DriveOptical Drive
A dumpload of ancient AGP cards Kingston Value DDR2-667 CL4 2T @CL3 1T Seagate 160GB 7200.10 LG IDE DVD-ROM 
CoolingCoolingOSMonitor
Ghettomade CPU waterblock 49cc 2stroke engine copper radiator WinXP SP2 32bit ProView 17" 
PowerCase
Tacens Radix V 550W Ghetto aluminium bench 
  hide details  
Reply
   
AGP bencher
(14 items)
 
CPUMotherboardGraphicsRAM
Phenom X6 1055T ASUS M4A89GTD Pro/USB3 Sapphire HD 6950 2GB Kingston HyperX DDR3-2000 
Hard DriveHard DriveCoolingCooling
Seagate 7200.12 Samsung SpinPoint F3 EK Supreme HF EK CoolStream XT360 
CoolingCoolingOSMonitor
Alpahcool Coolplex Pro 10LT Phobya DC12-400 Windows 7 Ultimate & Fedora 17 LG IPS235V 
MonitorKeyboardPowerCase
LG E2250V Logitech G11 NOX Sonar 780W (Kingwin 750W 80+) Lian Li PC-A05NB 
MouseAudio
Logitech G9 ASUS Xonar DX 
CPUMotherboardGraphicsRAM
AMD A10-5700 Gigabyte F2A75M-HD2 Radeon 7660D G.SKILL Ares 2133 CL9 
Hard DriveCoolingOSOS
Hitachi 5K750 Noctua NH-L9a Fedora 18 Windows 7 x64 
MonitorKeyboardPowerCase
AUO B156HW01 Logitech MK220  PicoPSU-80-WI-25V AIO Aluminium Handmade 
Other
TP-LINK 150 N/G/B 
CPUCPUCPUMotherboard
Core2Duo E6400 Core2Quad Q6600 Pentium Dual Core E5200 AsRock 4COREDUAL-SATA2 R2.0 
GraphicsRAMHard DriveOptical Drive
A dumpload of ancient AGP cards Kingston Value DDR2-667 CL4 2T @CL3 1T Seagate 160GB 7200.10 LG IDE DVD-ROM 
CoolingCoolingOSMonitor
Ghettomade CPU waterblock 49cc 2stroke engine copper radiator WinXP SP2 32bit ProView 17" 
PowerCase
Tacens Radix V 550W Ghetto aluminium bench 
  hide details  
Reply
post #10400 of 11269
Thread Starter 
Quote:
Originally Posted by drkidd22 View Post

Nah, It's not only with the 1066 that I see this problem.
I also have four 512MB Corsair DDR2 800MHz (CM2X512A-6400) and the system won't POST with those as well when all slots are populated.
I have done the same testing with the 512MB sticks and with same result. The MB won't even POST with the good 2048MB Corsair Stick I have when it's installed in slot B1 by itself.

Here is my CPU-Z Validation.
2434253.png

Disable SLI Ram settings and make sure the command rate is set at 2T not 1T and you should be able to use all 4 slots fully populated.

Edit: You may need to loosen the ram timings but I doubt it and or bump up the voltage on the ram a tad. 2.1+ volts is where I always run 4 sticks.
Edited by N2Gaming - 7/10/12 at 9:12am
Black N Blue Baby
(13 items)
 
CPUMotherboardGraphicsRAM
Ph II X4 955 BE (C3) @ 3.5GHz MSI NF980-G65 2x MSI Cyclone GTX 460 1GB +1x MSI 460 768MB PhysX 8GB Crucial Ballistix Tracer BL2KIT25664TN1337 
Hard DriveOptical DriveOSMonitor
6x1TB Samsung F3 Spinpoint RAID 0+1 LG 20x DVD Lightscribe Burner Win7 Ult x64 / XP Pro x64 Samsung LN-S4095D 1080P 40" LCD TV 
KeyboardPowerCaseMouse
G15 + Microsoft Wireless Desktop Elite Corsair HX1000w Mod'd Antec Nine Hundred G9x & Microsoft Wireless IntelliMouse Explore 2.0 
Mouse Pad
Big Black Pad 
  hide details  
Reply
Black N Blue Baby
(13 items)
 
CPUMotherboardGraphicsRAM
Ph II X4 955 BE (C3) @ 3.5GHz MSI NF980-G65 2x MSI Cyclone GTX 460 1GB +1x MSI 460 768MB PhysX 8GB Crucial Ballistix Tracer BL2KIT25664TN1337 
Hard DriveOptical DriveOSMonitor
6x1TB Samsung F3 Spinpoint RAID 0+1 LG 20x DVD Lightscribe Burner Win7 Ult x64 / XP Pro x64 Samsung LN-S4095D 1080P 40" LCD TV 
KeyboardPowerCaseMouse
G15 + Microsoft Wireless Desktop Elite Corsair HX1000w Mod'd Antec Nine Hundred G9x & Microsoft Wireless IntelliMouse Explore 2.0 
Mouse Pad
Big Black Pad 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: AMD Motherboards
Overclock.net › Forums › AMD › AMD Motherboards › [Official] ASUS M2N-SLI and M2N32-SLI Club!