Overclock.net › Forums › Intel › Intel Motherboards › Gigabyte EP45-UD3 Series Owners Guide
New Posts  All Forums:Forum Nav:

Gigabyte EP45-UD3 Series Owners Guide - Page 1610

post #16091 of 21186
Quote:
Originally Posted by mistargill View Post
my 4.0ghz setting. Is there anything I can improve on? I've been hearing mixed opinion about llc but what are your guys thoughts?

Code:
******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.05GHz...........................[ 450 x 9.0]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 450 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ] 
PCI Express Clock Drive.........................[ 900mv ] 
CPU Clock Skew..................................[ 0ps 
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ Auto ]
System Memory Multipler.........................[ 2.66D ] 
Memory Frequency 1066...........................[ 1200 ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]

******Advanced Timing Control******

tRRD[3].........................................[ 3 ]
tWTR[3].........................................[ 3 ]
tWR[6]..........................................[ 6 ]
tRFC[54]........................................[ 52 ]
tRTP[3].........................................[ 3 ]
Command Rate (cmd)[0]...........................[ 2 ]

******Channel A Timing Settings****** 

Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ OC-1200 ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings****** 

Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ OC-1200 ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled] [Disabled]
CPU Vcore [ 1.15 ]...................[ 1.350v ] [1.400v]
CPU Termination [ 1.20 ]...................[ 1.30 ]
CPU PLL [ 1.50 ]...................[ 1.45 ]
CPU Reference [ 0.760 ]...................[ 0.848 ]

MCH Core [ 1.100 ]...................[ 1.30 ]
MCH Reference [ 0.760 ]...................[ 0.863 ] 
MCH/DRAM Refernce [ 0.900 ]...................[ Normal ]
ICH I/O [ 1.500 ]...................[ 1.500 ]
ICH Core [ 1.100 ]...................[ 1.100 ]

DRAM Voltage [ 1.800 ]...................[ 2.10ov ]
DRAM Termination [ 0.900 ]...................[ Normal]
Channel A Ref [ 0.900 ]...................[ Normal ]
Channel B Ref [ 0.900 ]...................[ Normal ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled  ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
llc disabled is fine for 4ghz but once you start going up to 4.25 4.32 ect your going to need much more voltage... 4.25 with llc disabled you will need about 1.47500v . so if you wanted to run 4.5ghz you would need about 1.6v lol.
llc is fine just dont run linx for your chips sake.
post #16092 of 21186
Thread Starter 
Looks good Dilyn. How are the temps now?
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
post #16093 of 21186
Quote:
Originally Posted by freakb18c1 View Post
edited that MIT give it a shot ! if this i don't work im stumped
freakb18c1

Thanks for helping me out the below settings you posted definitely on the right track they let me boot up at and get into windows @ 4.0 finally. Just not stable yet keeps going BSD on me

The
CPU Reference [ 0.760 ]...................[ ] < set 0.745 @ 1.20vtt and
MCH Reference [ 0.760 ]...................[ ] < set 0.800 @ 1.200 vtt
settings is what had me screwed up didn't understand what you meant there so i had these settings wrong from the start once someone set me straight on what i needed to do it booted right up


Can you or anyone please help me find the settings i need to get it stable ?


Code:
******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Turbo    ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.5GHz............................[ 500 x 8.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 800mv   ]
PCI Express Clock Drive.........................[ 800mv   ]
CPU Clock Skew..................................[ 50ps     ]
MCH Clock Skew..................................[ 100ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Turbo    ]
Extreme Memory Profile (X.M.P)..................[ Disabled ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1200     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ Auto        ]
tWTR[4].........................................[ Auto        ]
tWR[13].........................................[ Auto        ]
tRFC[68] .......................................[ Auto        ] 
tRTP[4].........................................[ Auto        ]
Command Rate (cmd)[0]...........................[ Auto        ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 8]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ auto       ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto       ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ oc1200]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 8]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto        ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto        ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto        ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto        ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ oc1200]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.1875  ]...................[ 1.4875v   ]
CPU Termination   [ 1.20    ]...................[ 1.360   ]
CPU PLL           [ 1.50    ]...................[ 1.50   ]
CPU Reference     [ 0.760   ]...................[ ] < set 0.745 @ 1.20vtt
 
MCH Core          [ 1.100   ]...................[ 1.46v   ] 
MCH Reference     [ 0.760   ]...................[ ] < set 0.800 @ 1.200 vtt
MCH/DRAM Refernce [ 0.900   ]...................[ normal   ]
ICH I/O           [ 1.500   ]...................[ 1.59   ]
ICH Core          [ 1.100   ]...................[ 1.2   ] 
 
DRAM Voltage      [ 1.800   ]...................[ 2.18 ] 
DRAM Termination  [ 0.900   ]...................[ normal   ]
Channel A Ref     [ 0.900   ]...................[ normal   ]
Channel B Ref     [ 0.900   ]...................[ normal   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
PC
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel-Core 2 Quad-Q8400 Revision-R0 VID-1.2875v Gigabyte EP45-UD3P Rev.1.0 F11C-Bios Nvidia 9800-GT (2x2GB) G.SKILL PC2-9600 DDR2-1200 
Hard DriveOSMonitorPower
WD-Raptor & Maxtor Windows-7 Ultimate-64Bit Dell-2408WFP Corsair-TX650W 
Case
Antec-902 
  hide details  
Reply
PC
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel-Core 2 Quad-Q8400 Revision-R0 VID-1.2875v Gigabyte EP45-UD3P Rev.1.0 F11C-Bios Nvidia 9800-GT (2x2GB) G.SKILL PC2-9600 DDR2-1200 
Hard DriveOSMonitorPower
WD-Raptor & Maxtor Windows-7 Ultimate-64Bit Dell-2408WFP Corsair-TX650W 
Case
Antec-902 
  hide details  
Reply
post #16094 of 21186
hey id give it some high ass voltage just to see if its even possible. you have a cool chip so if you dont mind the high volts... shoot 1.500v if its not stable...... id go for a nice 3.6 oc..
post #16095 of 21186
so basically for Vtt Cpu ref and Mph ref. I just have to set them all of em to

1.2 / 0.785/ 0.800 first than Only touch vtt from then on?
Maestro(Flexin')
(13 items)
 
  
CPUMotherboardGraphicsRAM
q9650@ 4ghz testing Rampage Formula MSI gtx 480 - 850/1700/1950 1.050v Mushkin Blackline 1066 4x2 (8gb) 
Hard DriveOptical DriveOSMonitor
Seagate 1.5tb, Spinpoint 1tb, Spinpoint 2tb Asus DRW-2014L1T DVD burner Win7 x64 Acer P243W 24 inch 
KeyboardPowerCaseMouse
Saitek Eclipse Antec Signature 850W CM STORM SNIPER G500 
Mouse Pad
black one with cushy 
  hide details  
Reply
Maestro(Flexin')
(13 items)
 
  
CPUMotherboardGraphicsRAM
q9650@ 4ghz testing Rampage Formula MSI gtx 480 - 850/1700/1950 1.050v Mushkin Blackline 1066 4x2 (8gb) 
Hard DriveOptical DriveOSMonitor
Seagate 1.5tb, Spinpoint 1tb, Spinpoint 2tb Asus DRW-2014L1T DVD burner Win7 x64 Acer P243W 24 inch 
KeyboardPowerCaseMouse
Saitek Eclipse Antec Signature 850W CM STORM SNIPER G500 
Mouse Pad
black one with cushy 
  hide details  
Reply
post #16096 of 21186
Quote:
Originally Posted by mistargill View Post
so basically for Vtt Cpu ref and Mph ref. I just have to set them all of em to

1.2 / 0.785/ 0.800 first than Only touch vtt from then on?
yes you set 1.20 first then adjust the cpu / mch ref then you can kick up the cpu termination
post #16097 of 21186
Quote:
Originally Posted by NoGuru View Post
Looks good Dilyn. How are the temps now?
The difference is still huge, but the temps dropped three C all around.

Who wants pics of the final? It looks pretty good for my first lap job.
Sandy Goodness
(17 items)
 
Sandy Mininess
(14 items)
 
Simply the best
(13 items)
 
CPUMotherboardGraphicsRAM
Intel i5 2500k @ 3.7GHz Gigabyte GA-Z68XP-UD4 EVGA GeForce GTX 760 2GB G.SKILL Ripjaws 16GB 4x4GB 2133MHz 
Hard DriveHard DriveHard DriveCooling
60GB OCZ Vertex 3 60GB OCZ Vertex 3 2x 1TB Western Digital Caviar Black (RAID 0) XSPC Rasa RX360 (CPU) 
OSOSMonitorKeyboard
Windows 8 x64 Professional ArchLinux x64 Dell UltraSharp U2312HM Das S Professional 
PowerCaseMouseAudio
Seasonic X650 Coolermaster HAF X Razer Naga Asus Xonar Essence STX 
CPUMotherboardGraphicsRAM
Something slow and mobile No idea The best Leaking 
Hard DriveOptical DriveOSMonitor
Not nearly enough for my CP It's removable! Linux - ta best!!!1!!! Bigger than yours 
KeyboardPowerCaseMouse
Mine has twenty eight keys A battery derrr Fat and blocky They scare elephants 
Mouse Pad
Useless 
  hide details  
Reply
Sandy Goodness
(17 items)
 
Sandy Mininess
(14 items)
 
Simply the best
(13 items)
 
CPUMotherboardGraphicsRAM
Intel i5 2500k @ 3.7GHz Gigabyte GA-Z68XP-UD4 EVGA GeForce GTX 760 2GB G.SKILL Ripjaws 16GB 4x4GB 2133MHz 
Hard DriveHard DriveHard DriveCooling
60GB OCZ Vertex 3 60GB OCZ Vertex 3 2x 1TB Western Digital Caviar Black (RAID 0) XSPC Rasa RX360 (CPU) 
OSOSMonitorKeyboard
Windows 8 x64 Professional ArchLinux x64 Dell UltraSharp U2312HM Das S Professional 
PowerCaseMouseAudio
Seasonic X650 Coolermaster HAF X Razer Naga Asus Xonar Essence STX 
CPUMotherboardGraphicsRAM
Something slow and mobile No idea The best Leaking 
Hard DriveOptical DriveOSMonitor
Not nearly enough for my CP It's removable! Linux - ta best!!!1!!! Bigger than yours 
KeyboardPowerCaseMouse
Mine has twenty eight keys A battery derrr Fat and blocky They scare elephants 
Mouse Pad
Useless 
  hide details  
Reply
post #16098 of 21186
Thread Starter 
Quote:
Originally Posted by Dilyn View Post
The difference is still huge, but the temps dropped three C all around.

Who wants pics of the final? It looks pretty good for my first lap job.
That sounds about right. I usually get 3-4 on most laps. Post the pic!
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
post #16099 of 21186
56k beware (so says Freak).
It's only 1024x768







I have more, but I'm pretty sure that you guys don't wanna see the whole thing

More of the beauty:






If only I could've used my web cam. The pics would've been ten times better.
Sandy Goodness
(17 items)
 
Sandy Mininess
(14 items)
 
Simply the best
(13 items)
 
CPUMotherboardGraphicsRAM
Intel i5 2500k @ 3.7GHz Gigabyte GA-Z68XP-UD4 EVGA GeForce GTX 760 2GB G.SKILL Ripjaws 16GB 4x4GB 2133MHz 
Hard DriveHard DriveHard DriveCooling
60GB OCZ Vertex 3 60GB OCZ Vertex 3 2x 1TB Western Digital Caviar Black (RAID 0) XSPC Rasa RX360 (CPU) 
OSOSMonitorKeyboard
Windows 8 x64 Professional ArchLinux x64 Dell UltraSharp U2312HM Das S Professional 
PowerCaseMouseAudio
Seasonic X650 Coolermaster HAF X Razer Naga Asus Xonar Essence STX 
CPUMotherboardGraphicsRAM
Something slow and mobile No idea The best Leaking 
Hard DriveOptical DriveOSMonitor
Not nearly enough for my CP It's removable! Linux - ta best!!!1!!! Bigger than yours 
KeyboardPowerCaseMouse
Mine has twenty eight keys A battery derrr Fat and blocky They scare elephants 
Mouse Pad
Useless 
  hide details  
Reply
Sandy Goodness
(17 items)
 
Sandy Mininess
(14 items)
 
Simply the best
(13 items)
 
CPUMotherboardGraphicsRAM
Intel i5 2500k @ 3.7GHz Gigabyte GA-Z68XP-UD4 EVGA GeForce GTX 760 2GB G.SKILL Ripjaws 16GB 4x4GB 2133MHz 
Hard DriveHard DriveHard DriveCooling
60GB OCZ Vertex 3 60GB OCZ Vertex 3 2x 1TB Western Digital Caviar Black (RAID 0) XSPC Rasa RX360 (CPU) 
OSOSMonitorKeyboard
Windows 8 x64 Professional ArchLinux x64 Dell UltraSharp U2312HM Das S Professional 
PowerCaseMouseAudio
Seasonic X650 Coolermaster HAF X Razer Naga Asus Xonar Essence STX 
CPUMotherboardGraphicsRAM
Something slow and mobile No idea The best Leaking 
Hard DriveOptical DriveOSMonitor
Not nearly enough for my CP It's removable! Linux - ta best!!!1!!! Bigger than yours 
KeyboardPowerCaseMouse
Mine has twenty eight keys A battery derrr Fat and blocky They scare elephants 
Mouse Pad
Useless 
  hide details  
Reply
post #16100 of 21186
More Cowbell, err Pics.
442
(15 items)
 
Q6600
(14 items)
 
Piece O' Crappola
(13 items)
 
CPUMotherboardGraphicsRAM
Q9550 E0 DFI LanParty LT P35-T2R 2 x HD4670QT512P CF Patriot PVS24G8500ELKN 
CoolingOSMonitorPower
Stock pfsense Acer H233H Antec EarthWatts 430 
CaseAudio
custom onboard 
CPUMotherboardGraphicsRAM
Q6600 B3 Lapped @ 3.4 GA-EP45-UD3R EVGA 9600GSO 384m 96SP 4G (2x2) Patriot Viper PC2-8500 
Hard DriveOptical DriveCoolingOS
80g Maxtor, 320WDC. 320Seagate NEC ND-3550 & LiteOn CM Hyper 212+ w/PP Blademasters XP Pro SP3 
MonitorPowerCase
Acer H233H Rosewill RG630-S12 NZXT BetaEVO 
CPUMotherboardGraphicsRAM
E6420 GA-P35-DS3L GeForce 7300LE 2G PNY PC2-6400 
Hard DriveOptical DriveOSMonitor
80Gig WDC SATA NEC ND3540A Win 7 Ultimate 64bit/XP Pro Acer H233H 
PowerCase
Antec Earthwatts 430 none 
  hide details  
Reply
442
(15 items)
 
Q6600
(14 items)
 
Piece O' Crappola
(13 items)
 
CPUMotherboardGraphicsRAM
Q9550 E0 DFI LanParty LT P35-T2R 2 x HD4670QT512P CF Patriot PVS24G8500ELKN 
CoolingOSMonitorPower
Stock pfsense Acer H233H Antec EarthWatts 430 
CaseAudio
custom onboard 
CPUMotherboardGraphicsRAM
Q6600 B3 Lapped @ 3.4 GA-EP45-UD3R EVGA 9600GSO 384m 96SP 4G (2x2) Patriot Viper PC2-8500 
Hard DriveOptical DriveCoolingOS
80g Maxtor, 320WDC. 320Seagate NEC ND-3550 & LiteOn CM Hyper 212+ w/PP Blademasters XP Pro SP3 
MonitorPowerCase
Acer H233H Rosewill RG630-S12 NZXT BetaEVO 
CPUMotherboardGraphicsRAM
E6420 GA-P35-DS3L GeForce 7300LE 2G PNY PC2-6400 
Hard DriveOptical DriveOSMonitor
80Gig WDC SATA NEC ND3540A Win 7 Ultimate 64bit/XP Pro Acer H233H 
PowerCase
Antec Earthwatts 430 none 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › Gigabyte EP45-UD3 Series Owners Guide