Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Cooler Master ATCS 840 Owners Club
New Posts  All Forums:Forum Nav:

[Official] Cooler Master ATCS 840 Owners Club - Page 425

post #4241 of 4392
I 'm not an expert, but I guess I have the case long enough for contributing! I' a little tired, but I'll try to make sense LOL.

On my old setup, I had the 2 x 230mm installed and I had the "front" (closest to power button) rpm-limited via resistor to reduce the short cycling effect.

Now, I have the 3 x 120mm red LED fans on top, and just below, I have the two fans of my H100i in pull (had no choice)...
One of those RED 120mm died on me yesterday, dunno if if was caused by anything special or just random failure. It's the "front" (closest to power button) one that failed...so I unplugged it...temperatures don't seem to be affected....I'll leave it there for now, as it's a PITA to take out.


If you look at my pictures a few pages back, you'll see that I installed an extra 120mm in a CM bay, right under the CD/DVD drive.... it's already dusty, so it pulls good and brings fresh air right close to my rad...

Think of it this way...even if "the top portion of the case" short cycles a little, your SEIDON's RAD might benefit, depends on how close to the front it's installed. You can use the fan duct and the bottom 120mms for more intake front the bottom /back sides, to negate the effects of the short-cycling...

For the half-and-down portion of the case, there is already plenty of fans (I use the fan duct for exhaust)...you can also use the AIR DUCT with fan set as INTAKE, which I was doing when I had 2 x 560TI's...my cards were kept really cool....
I really wish I could use some sort of harmless smoke to "figure visually" the airflow and figure what's best...

Anyway, as I'm overclocking with Haswell 4770k and apparently more cooling was needed, I'd rather keep my rig like in the pic, the CPU temps being my main concern...

I recently added a 120mm at the bottom of the case, not shown on the pic...
Next step is to get rid of the single 560TI and grab 2 X 760s or 770s in SLI....then I'll be more concerned about airflow in the lower-half portion...I think I'll be alright!


Edited by delavan - 9/24/13 at 12:35pm
post #4242 of 4392
Quote:
Originally Posted by delavan View Post


Spunky, it's very hard to do (the sheet metal is flimsy). Your best bet would be to bring it to a specialized sheet metal shop, where they use laser cutting or plasma cutting equipment......like the places where they manufacture stainless steel commercial kitchen counters....

you could also buy/borrow a dremel tool and use small cutting disks (would take quite a few disks and put some EYE PROTECTION!!!!!!!) that would be a little crappy to do, but wouldn bend. then you could use another attachment to sand the edges..anyway, with window kits come a rubber trim that would "cover" the small defaults...

A sheet metal shop might be the deal if not too expensive. You could also look for a hand tool (not the power version) called a sheet metal nibbler. Should handle the thin aluminum easily, but you'll want to practice how it handles corners.

[/quote]Penicilyn,

Make sure all case screws are tight. also, you might want to reduce fan speed, as too much airflow/vibration tends to "reverberate". The case is very big as you know and the side panels are somewhat flimsy. you might want to think about installing sticky acoustic insulation on the side panels to "dampen" everything.[/quote]

Yes, start with all the screws. Somewhere in these threads someone mentioned one or more fans actaully rattling in its mount. You could remove the sides one at a time to see if that's where the rattle is coming from. The idea of the acoustic insulation has always bothered me because it seems like it would also act as thermal insulation and keep more heat in the case. The aluminum sides are radiating at least some heat out of the case. I think you could just add stiffeners to the side panel(s) to kill any panel vibration. Say 1/2" aluminum angle bars. Adhere with silicone caulk or if you don't mind the look use pop rivets.
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
post #4243 of 4392

Sleep deprivation lead to mistaken post...sorry guys.

 

~Kat


Edited by oldAMDnew2Intel - 9/27/13 at 6:57am
i7WorkStation
(27 items)
 
   
  hide details  
Reply
i7WorkStation
(27 items)
 
   
  hide details  
Reply
post #4244 of 4392
I have an EX360 radiator up top in push pull fan config and I am going to add an AX120 radiator to my loop - I was thinking of putting it at the bottom, replacing the fan there that I currently have blowing air into the case.

I was wondering what would be the best order in this new setup? I have the reservoir/pump in a dual drive bay, the outlet then goes to the CPU, then GPU, then radiator at case top, and back to reservoir. In the new setup, should I do reservoir/pump to CPU to 120mm radiator at the bottom, to GPU, to 360 radiator at top, back to reservoir?

Also, I am not sure about airflow config. I have the 360 radiator exhausting out. The front case fan in and the rear fan exhausting out. Should I keep these the same when adding the 120mm radiator? And should the 120mm radiator pull config fan also exhaust out I assume since I don't want to bring warm air to the other radiator? Any opinions on the best setup for this case? I prefer to keep all the radiators inside.
My System
(17 items)
 
  
CPUMotherboardGraphicsRAM
Ryzen R7 1700x Asrock X370 Taichi EVGA GTX 1080 Ti Founder Edition with Hybrid Co... 16 GB DDR4 G.skill Flare X 3200 
Hard DriveHard DriveHard DriveOptical Drive
512GB Samsung 840 Pro 3 TB Western Digital Black 3 TB Toshiba LG WH14NS40 Blu-ray Writer 
CoolingCoolingOSMonitor
NZXT Kraken X52 Gentle Typhoon AP-15 Windows 10 Samsung KU6300 40 inch 4k HDTV 
KeyboardPowerCaseMouse
Cooler Master MasterKeys Pro L RGB with Cherry ... EVGA Supernova 1000 P2 Phanteks Enthoo Luxe Tempered Glass Edition Logitech G900 Chaos Spectrum 
Mouse Pad
Razer Scarab 
  hide details  
Reply
My System
(17 items)
 
  
CPUMotherboardGraphicsRAM
Ryzen R7 1700x Asrock X370 Taichi EVGA GTX 1080 Ti Founder Edition with Hybrid Co... 16 GB DDR4 G.skill Flare X 3200 
Hard DriveHard DriveHard DriveOptical Drive
512GB Samsung 840 Pro 3 TB Western Digital Black 3 TB Toshiba LG WH14NS40 Blu-ray Writer 
CoolingCoolingOSMonitor
NZXT Kraken X52 Gentle Typhoon AP-15 Windows 10 Samsung KU6300 40 inch 4k HDTV 
KeyboardPowerCaseMouse
Cooler Master MasterKeys Pro L RGB with Cherry ... EVGA Supernova 1000 P2 Phanteks Enthoo Luxe Tempered Glass Edition Logitech G900 Chaos Spectrum 
Mouse Pad
Razer Scarab 
  hide details  
Reply
post #4245 of 4392
Hey, new to oc.net - I've been a proud owner of the ATCS 840 for quite some time! biggrin.gif

But now the front 230mm intake fan started to develop an annoying noise.
What replacement fan can you recommend? I'd prefer it to be on the more silent side.

Thanks thumb.gif
post #4246 of 4392
Quote:
Originally Posted by tivtag View Post

the ATCS 840 front 230mm intake fan started to develop an annoying noise. What replacement fan can you recommend? I'd prefer it to be on the more silent side. Thanks thumb.gif

Tivtag, when I bought the case I figured that those 230mm fans might be hard to replace someday and I bought two spares from CM. First choice would be to see if CM still has spares. There aren't too many 200-230mm fans out there to choose from. You'd have to measure and see what combinations of smaller fans would fit in the space (and you might need to make some brackets). Noctuas are really quiet.

The case came with brackets to replace the two top 230s with three 120s (I think). You could do that and move one of the 230s to the front. And then you'd have a spare.

In some old threads there was a discussion of the top 230s making noise when new it turned out the be loose mounting brackets. So check for some mounting vibration. There are also disussions out there (maybe not on OC) about lubricating fan bearings and that might be worth a try if the alternative is to scrap the fan.

Old Guy
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
post #4247 of 4392
Quote:
Originally Posted by Old Guy View Post

Tivtag, when I bought the case I figured that those 230mm fans might be hard to replace someday and I bought two spares from CM..

Turned out I've still had the 230mm fans I've removed from the top way back then. (I'm not using any top mounted fans)
Replacing the front fan was very easy and now I am back to having a silent PC. Thanks! biggrin.gif
post #4248 of 4392
Tivtag, I'm glad that worked out. Isn't it funny what you find that you forgot about when you look in boxes and closets, etc.!
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
post #4249 of 4392
Wow, there are posts in this thread? Cool, I'm in thumb.gif ! I have two of these. One is going to be passed to my wife to use with my old ASUS Rampage Extreme (The originator) LGA775, Q9550s, 8GB of OCZ Reaper, Kingwin 1220Watt Mach1 PSU, 2x 80GB Velociraptors, 2x 500GB ED Blues, and an ASUS HD7870. The Case is going to get my ASUS Rampage IV Extreme Black Edition LGA2011, I'm looking forward to this build!

So does anyone think CM screwed up discontinuing this case instead of just doing minor updates?
    
CPUMotherboardGraphicsRAM
P4 HT 3.06 Abit IC7Max3 HIS IceQ HD4670 2 GB Corsair (Forgot) 
Hard DriveOptical DriveOSMonitor
500 gb Samsung Sony Windows 7 Pro 32bit Asus 20" 
KeyboardPowerCaseMouse
Yellow and black Aero 750watt Wavemaster Microsoft Sidewinder 
Mouse Pad
Bumble Bee print 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
P4 HT 3.06 Abit IC7Max3 HIS IceQ HD4670 2 GB Corsair (Forgot) 
Hard DriveOptical DriveOSMonitor
500 gb Samsung Sony Windows 7 Pro 32bit Asus 20" 
KeyboardPowerCaseMouse
Yellow and black Aero 750watt Wavemaster Microsoft Sidewinder 
Mouse Pad
Bumble Bee print 
  hide details  
Reply
post #4250 of 4392
Quote:
Originally Posted by Werewolf486 View Post

So does anyone think CM screwed up discontinuing this case instead of just doing minor updates?

I dunno. I know I'm so old *I'm a dinosaur. By maybe al us desktop types are dinosaurs. Maybe so much of the world is going to phones and tablets that there is no cost reovery in developing a new tower case that seven people in the whole world will buy.
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
Evolving Plan
(35 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Xeon W3680 Westmere-EP Gigabyte GA-X58A-UD3R (Rev. 2) PNY (Nvidia) Quadro 2000 1GB PNY (Nvidia) Quadro 400 for 3rd monitor 
RAMHard DriveHard DriveHard Drive
Mushkin Silverline (6 x 4)=24 GB DDR3 1333 C(OS): 120GB OCZ Vertex 3 - MAX IOPS Edition, S... D(Data): two WD RE4 1TB 3.0Gb/s (RAID 1)  Two WD RE4 1TB 3.0Gb/s to be used in hot swap b... 
Hard DriveHard DriveHard DriveOptical Drive
WD Blue 500AZLX 500GB, in hot swap bay. Used t... Two PATA legacy drives mounted between PSU (rea... LaCie D2 Quadra 1TB e-SATA 3.0 Gb/s (for immedi... Sony Optiarc AD-7261S-OB 
CoolingCoolingCoolingCooling
Case stock fans: one 230mm front intake, two 23... CM External GPU Duct & CM 120mm Ex. Fan Noctua NF-P14 FLX 140mm (addl. bottom case intake) Noctua NF-P14 FLX 140mm (addl. rear case exhaust) 
CoolingCoolingCoolingCooling
Prolimatech Megahalems Rev. B. CPU heat sink Noctua NF-P12 1300R 120mm push fan on CPU heat ... Scythe Kaze Master Pro 6 channel fan controller 70mm fan on i-Star hot swap HDD cage (disconnec... 
OSMonitorMonitorMonitor
Windows 7 Professional 64 bit HP Pavilion 23xi HP Pavillion 27xi (1) HP Pavillion 27xi (2) 
KeyboardPowerCaseMouse
Logitech K330 Wireless w/mouse Seasonic Platinum-860 80 Plus 860 Watts ... CM ATCS 840 (minor mods) Logitech K330 wireless 
Mouse PadAudioOtherOther
Some freebee with an advert on it Cyber Acoustics CA-1001WB 5.25" Drive Bay for now  i-Star USA three bay, 3.5" hot swap cage (in tw... Drive A: Internal FDD w/ multi card readers & 1... 
OtherOtherOther
Startech USB 2.0. 7 port PCI Card 8GB Verbatim Flash Drive. Internal system docu... Netgear N900 Router 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Computer Cases
Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Cooler Master ATCS 840 Owners Club