Overclock.net › Forums › Case Mods & Cases › Other Hardware Mods › Cables and Sleeving › Cable Sleeving Gallery & Discussion
New Posts  All Forums:Forum Nav:

Cable Sleeving Gallery & Discussion - Page 1373

post #13721 of 13725
do you not have a wire you can dismantle to get the pin out for it?
post #13722 of 13725
Quote:
Originally Posted by Craigk19 View Post

do you not have a wire you can dismantle to get the pin out for it?

No, Theirs no six pcie in any of my PSU boxes. The only one I have is the 6+2 version. I can't really see how it's wired since their sleeved & heatshrink is basically superglue to the wires.
post #13723 of 13725

The nine 8pin VGA outlets on that PSU have the same SQU-RND-RND-RND configuration as a GPU/PCIE and none of them doubles as an EPS outlet, so it would be perverse for the wires not to be 1x1.

 

If that is the case, looking at the outlets with the PSU fan on the bottom and the lug of each outlet below the pins, the wires, left to right, top to bottom, would be 12V-12V-12V-Grd/Grd-Grd-Grd-Grd, so the PSU end of a 6pin GPU cable would be 12V-12V-12V-Nil/Grd-Grd-Grd-Nil.

 

If your EPS cable for that PSU is 1x1, with the wire arrangement above the lug Grd-Grd-Grd-Grd/12V-12V-12V-12V - seeing as the CPUZ outlets have the SQU-RND-RND-SQU configuration of an EPS motherboard socket - that would be an even stronger indication that this was so.

 

If you have a PSU tester - which anyone building a cable set ought to have - you could make up a 1x1 6pin cable and test it.

 

If you have a multimeter it would be enough to confirm the arrangement by testing your 6+2 cable.


Edited by Himo5 - 4/27/17 at 4:21pm
Calimo Min
(22 items)
 
Calimo Mid
(15 items)
 
 
CPUMotherboardRAMHard Drive
Amd A10-5800K Gigabyte F2A85X-UP4 G.Skill F3-2666C11D-8GTXD WD Caviar 1002FAEX-1Tb 
Hard DriveHard DriveHard DriveHard Drive
3TB WD WD30EURS AV-GP, SATA III, IntelliPower Seagate ST400DM000 4TB Barracuda SATA-III - 590... Seagate ST400DM000 4TB Barracuda SATA-III - 590... Seagate ST400DM000 4TB Barracuda SATA-III - 590... 
Hard DriveOptical DriveCoolingCooling
Seagate ST400DM000 4TB Barracuda SATA-III - 590... Optiarc AD-7280S DVD-RW Scythe: Mugen 3 2 off Scythe AP15 Gentle Typhoon Fan 
CoolingOSMonitorKeyboard
1 off Zaward 140mm ZG2-140B Golf PWM Top Fan MS Windows 7 Ultimate w/SP1- 64 Bit Edition Samsung 2333SW Saitek Cyborg C5 
PowerCaseMouseAudio
Corsair TX650 Watt Casecom 5288 Type KM  Gigabyte GM-M6800 Trust SP6210 5.1 w/modded speakers 
OtherOther
Leadtek Winfast DTV1000S DVB-T Tuner card HD600X-LV Optoma projector 
  hide details  
Reply
Calimo Min
(22 items)
 
Calimo Mid
(15 items)
 
 
CPUMotherboardRAMHard Drive
Amd A10-5800K Gigabyte F2A85X-UP4 G.Skill F3-2666C11D-8GTXD WD Caviar 1002FAEX-1Tb 
Hard DriveHard DriveHard DriveHard Drive
3TB WD WD30EURS AV-GP, SATA III, IntelliPower Seagate ST400DM000 4TB Barracuda SATA-III - 590... Seagate ST400DM000 4TB Barracuda SATA-III - 590... Seagate ST400DM000 4TB Barracuda SATA-III - 590... 
Hard DriveOptical DriveCoolingCooling
Seagate ST400DM000 4TB Barracuda SATA-III - 590... Optiarc AD-7280S DVD-RW Scythe: Mugen 3 2 off Scythe AP15 Gentle Typhoon Fan 
CoolingOSMonitorKeyboard
1 off Zaward 140mm ZG2-140B Golf PWM Top Fan MS Windows 7 Ultimate w/SP1- 64 Bit Edition Samsung 2333SW Saitek Cyborg C5 
PowerCaseMouseAudio
Corsair TX650 Watt Casecom 5288 Type KM  Gigabyte GM-M6800 Trust SP6210 5.1 w/modded speakers 
OtherOther
Leadtek Winfast DTV1000S DVB-T Tuner card HD600X-LV Optoma projector 
  hide details  
Reply
post #13724 of 13725
Quote:
Originally Posted by Himo5 View Post

The nine 8pin VGA outlets on that PSU have the same SQU-RND-RND-RND configuration as a GPU/PCIE and none of them doubles as an EPS outlet, so it would be perverse for the wires not to be 1x1.

If that is the case, looking at the outlets with the PSU fan on the bottom and the lug of each outlet below the pins, the wires, left to right, top to bottom, would be 12V-12V-12V-Grd/Grd-Grd-Grd-Grd, so the PSU end of a 6pin GPU cable would be 12V-12V-12V-Nil/Grd-Grd-Grd-Nil.

If your EPS cable for that PSU is 1x1, with the wire arrangement above the lug Grd-Grd-Grd-Grd/12V-12V-12V-12V - seeing as the CPUZ outlets have the SQU-RND-RND-SQU configuration of an EPS motherboard socket - that would be an even stronger indication that this was so.

If you have a PSU tester - which anyone building a cable set ought to have - you could make up a 1x1 6pin cable and test it.

If you have a multimeter it would be enough to confirm the arrangement by testing your 6+2 cable.

I have a older cable from CableMod for P2 series. I'll just use that as a reference(removing the +2 connector & wire). Also icemodz has been helping me. They said none of EVGA GPU cables use double crimp wires. The only cable that uses double crimp wiring is the main ATX cable.
post #13725 of 13725
d8481b3a_GYb8BvA.jpeg
8860d515_r8kIzsc.jpeg
aafffad6_RKNhHcA.jpeg

Heatshrink seem a bit thick, This was just a test before I start my Sata & Molex cables. I have much smaller glue versions of heatshrink.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Cables and Sleeving
Overclock.net › Forums › Case Mods & Cases › Other Hardware Mods › Cables and Sleeving › Cable Sleeving Gallery & Discussion