Overclock.net › Forums › Intel › Intel Motherboards › [Official] --The Asus P6X58D Premium & E Thread--
New Posts  All Forums:Forum Nav:

[Official] --The Asus P6X58D Premium & E Thread-- - Page 152

post #1511 of 6378
Need a hand here.

Trying to install Win7 on a new RAID0 set of 3 drives. Created the raid set ok in the marvel configuration but Windows says it can't install windows on this disk. I thought you didn't need raid drivers for win 7.

Bios is 0703. Do I need drivers? I don't have a floppy drive!
Black n Blue
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i7 930 4.0GHz@1.27v HT on (3001A135) Asus P6X58D Premium 8800GT x 2 in SLi plus GT240 12Gb Corsair Dominator C8 with Corsair Airflow fan 
Hard DriveOptical DriveOSMonitor
2x Intel 80GB SSD Raid0 + 3x Samsung F3 1TB Raid0 Pioneer BD-RW Win7 Ultimate 64 Samsung 24" 2494 + 2x Acer 22" 
KeyboardPowerCaseMouse
G15 Corsair 1000HX HAF 932 Custom Paint G3 
  hide details  
Reply
Black n Blue
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i7 930 4.0GHz@1.27v HT on (3001A135) Asus P6X58D Premium 8800GT x 2 in SLi plus GT240 12Gb Corsair Dominator C8 with Corsair Airflow fan 
Hard DriveOptical DriveOSMonitor
2x Intel 80GB SSD Raid0 + 3x Samsung F3 1TB Raid0 Pioneer BD-RW Win7 Ultimate 64 Samsung 24" 2494 + 2x Acer 22" 
KeyboardPowerCaseMouse
G15 Corsair 1000HX HAF 932 Custom Paint G3 
  hide details  
Reply
post #1512 of 6378
Guys, i just did xMisery's Overclocking 3.61ghz Stable Guide. Its stable.
But my ram is still not running at 1600mhz, and i want it to run at the timings it should run at.
Any help guys? What should i change?
I tried setting the CPU ratio setting to 17.0 then upping the BCLK Freq. to the point the DRAM Freq is at 1603mhz. upped the CPU voltage a fraction, and the DRAM Bus voltage to 1.66.

But it BSOD...

Quote:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[172]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1379MHz]
UCLK Frequency.........................[2758MHz]
QPI Link Data Rate.....................[Auto]

CPU Voltage Control....................[Manual]
CPU Voltage............................[1.11875]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.20625]
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]

Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]

C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
Any ideas?

P.s i changed the DRAM timings to
[7]
[7]
[7]
[20]
auto auto auto etc.

But idk if that had anything to do with the BSOD....
Alpha Blue Wolf
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel Core i7 920 D0 @ 3.8ghz Asus P6X58D Premium ATI XFX Radeon HD 5870 Corsair Domi. GT 6GB CMG6GX3M3A1600C7 @ 7-7-7-20 
Hard DriveOptical DriveOSMonitor
1TB Seagate 7200rpm 32MB 22x LG DVD Super Multi DVD+/-RW Windows 7 Home Premium 64 - Bit 23"HDTV Samsung SyncMaster + 26"AOC Monitor 
KeyboardPowerCaseMouse
Razer Lycosa Gaming Keyboard - Backlit Corsair 950W TX Antec Nine Hundred Two + 2 Extra Fans Razer Deather Adder V2 3500DPI 
  hide details  
Reply
Alpha Blue Wolf
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel Core i7 920 D0 @ 3.8ghz Asus P6X58D Premium ATI XFX Radeon HD 5870 Corsair Domi. GT 6GB CMG6GX3M3A1600C7 @ 7-7-7-20 
Hard DriveOptical DriveOSMonitor
1TB Seagate 7200rpm 32MB 22x LG DVD Super Multi DVD+/-RW Windows 7 Home Premium 64 - Bit 23"HDTV Samsung SyncMaster + 26"AOC Monitor 
KeyboardPowerCaseMouse
Razer Lycosa Gaming Keyboard - Backlit Corsair 950W TX Antec Nine Hundred Two + 2 Extra Fans Razer Deather Adder V2 3500DPI 
  hide details  
Reply
post #1513 of 6378
Hey Guys,

I recently tried Xmisery's settings below to overclock my 920 to 3.8. Since the majority of my work is encoding blu-rays to mkv i figured maybe it was time to decrease the encoding times and increase the FPS on ripbot264 and finish my quest of encoding my 150 blu-rays from my collection. From regular stock speeds i saw a huge increase in FPS but I kept getting x264_x86, _x64.exe errors after a few successful encodes. No Reboots, No BSODs. My Temps at full load were about 69-74 degrees and Half Load came to a cool 55-58 degrees. The guys at Doom9 suggested that it may have been some encoding software issues so i ended re-installing my entire Windows OS and afterwards I encoded 2 movies with no problems and then the problem came back. Basically just app crashes. I reverted back to my normal 2.6 stock speeds for now until i can get some advice on how to fix this. I was thinking about bumping up the wattage on the CPU but wanted to get some advice first before i do this. Just to be safe.

At Stock speeds i have no problems with the encodes.


These are my specs below:
Antec 900 Case (4 Fans)
i7 920 (Stock)
Artic Cooling Freezer Pro Rev 2
P6X58D
Corsair Dominator 6GB 1600
ATI 5770HD
Corsair 750 WATT PS
1.5T WD
640GB Black WD
Blu-Ray Drive


Thanks!




Quote:
Originally Posted by xmisery View Post
***************************************
Running 3.80GHz w/o HyperThreading (Stable)
***************************************

Code:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[181]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1451MHz]
UCLK Frequency.........................[2903MHz]
QPI Link Data Rate.....................[Auto]

CPU Voltage Control....................[Manual]
CPU Voltage............................[1.15625]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.20000]
IOH Voltage............................[1.12]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]

Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]

C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
**************************************
Running 3.80GHz w/ HyperThreading (Stable)
**************************************

Code:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[181]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1451MHz]
UCLK Frequency.........................[2903MHz]
QPI Link Data Rate.....................[Auto]

CPU Voltage Control....................[Manual]
CPU Voltage............................[1.16875]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.20000]
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]

Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]

C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
NOTE: .
My I7 920
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel I7 920 D0 - Testing @ 4.0GHZ Asus P6X58D HD5770 Corsair Dominator 6GB 
Hard DriveOSMonitorKeyboard
WD Black 640GB and 1.5TB Windows 7 Ultimate 64bit Acer 23" 1080P Dell 
PowerCaseMouse
Corsair 750 Watt Antec 900 Dell 
  hide details  
Reply
My I7 920
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel I7 920 D0 - Testing @ 4.0GHZ Asus P6X58D HD5770 Corsair Dominator 6GB 
Hard DriveOSMonitorKeyboard
WD Black 640GB and 1.5TB Windows 7 Ultimate 64bit Acer 23" 1080P Dell 
PowerCaseMouse
Corsair 750 Watt Antec 900 Dell 
  hide details  
Reply
post #1514 of 6378
Quote:
Originally Posted by paleblue View Post
Need a hand here.

Trying to install Win7 on a new RAID0 set of 3 drives. Created the raid set ok in the marvel configuration but Windows says it can't install windows on this disk. I thought you didn't need raid drivers for win 7.

Bios is 0703. Do I need drivers? I don't have a floppy drive!
whats hds are you trying to raid 0 ? 3x1tb ?

i tryed to do my 2x1.5tb bit 2tb is the max but for some reason i had to do them as like there where single driver 1.3X each and it worked

when setting up raid it tells you if its a bootable drive is it says no then you cant use it you have to make it smaller volume
My System
(15 items)
 
  
CPUMotherboardGraphicsGraphics
i7 3770K ASUS Maximus V Gene HD 7970 HD 7970 
RAMCoolingMonitorPower
Team Xtreem LV 16GB (2 x 8GB) H20 CROSSOVER 27Q LED-P 27" Enermax 1050W Revolution 85+ 
Case
Danger Den Torture Rack 
  hide details  
Reply
My System
(15 items)
 
  
CPUMotherboardGraphicsGraphics
i7 3770K ASUS Maximus V Gene HD 7970 HD 7970 
RAMCoolingMonitorPower
Team Xtreem LV 16GB (2 x 8GB) H20 CROSSOVER 27Q LED-P 27" Enermax 1050W Revolution 85+ 
Case
Danger Den Torture Rack 
  hide details  
Reply
post #1515 of 6378
Quick question.

Can I use the OC settings for the 920 to overclock my 930 on the motherboard?

I haven't found a good place to start OCing with this setup and am very inexperienced. I just want a 3.8ghz or so OC.

Thanks
post #1516 of 6378
Well I managed to clock the 920 back to 3.8 again and i ran the IBT test for 20 passes on very high settings. Appcrash just like Ripbot264 after 12 passes.

See Below






I think i'm going to run the test again on standard and see if it passes.

You guys think i should bump up the voltage a bit and about how much?
Edited by theshadow1234 - 4/2/10 at 10:31am
My I7 920
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel I7 920 D0 - Testing @ 4.0GHZ Asus P6X58D HD5770 Corsair Dominator 6GB 
Hard DriveOSMonitorKeyboard
WD Black 640GB and 1.5TB Windows 7 Ultimate 64bit Acer 23" 1080P Dell 
PowerCaseMouse
Corsair 750 Watt Antec 900 Dell 
  hide details  
Reply
My I7 920
(13 items)
 
  
CPUMotherboardGraphicsRAM
Intel I7 920 D0 - Testing @ 4.0GHZ Asus P6X58D HD5770 Corsair Dominator 6GB 
Hard DriveOSMonitorKeyboard
WD Black 640GB and 1.5TB Windows 7 Ultimate 64bit Acer 23" 1080P Dell 
PowerCaseMouse
Corsair 750 Watt Antec 900 Dell 
  hide details  
Reply
post #1517 of 6378
Quote:
Originally Posted by DOM. View Post
whats hds are you trying to raid 0 ? 3x1tb ?

i tryed to do my 2x1.5tb bit 2tb is the max but for some reason i had to do them as like there where single driver 1.3X each and it worked

when setting up raid it tells you if its a bootable drive is it says no then you cant use it you have to make it smaller volume
I was just trying to load windows to run some stress tests using the 3 1TB raid 0 set - after it's all good I'll move my two SSDs over from my current machine and make them the boot volume.

Yes the problem was that such a large volume isnt bootable. I made a 70GB vol and that worked fine. The problem now is that win7 won't allow me to have a 2.7 TB vol. It splits it to a max of 2 TB. Is there a way around that? I'd like a larger volume really.
Black n Blue
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i7 930 4.0GHz@1.27v HT on (3001A135) Asus P6X58D Premium 8800GT x 2 in SLi plus GT240 12Gb Corsair Dominator C8 with Corsair Airflow fan 
Hard DriveOptical DriveOSMonitor
2x Intel 80GB SSD Raid0 + 3x Samsung F3 1TB Raid0 Pioneer BD-RW Win7 Ultimate 64 Samsung 24" 2494 + 2x Acer 22" 
KeyboardPowerCaseMouse
G15 Corsair 1000HX HAF 932 Custom Paint G3 
  hide details  
Reply
Black n Blue
(13 items)
 
  
CPUMotherboardGraphicsRAM
Core i7 930 4.0GHz@1.27v HT on (3001A135) Asus P6X58D Premium 8800GT x 2 in SLi plus GT240 12Gb Corsair Dominator C8 with Corsair Airflow fan 
Hard DriveOptical DriveOSMonitor
2x Intel 80GB SSD Raid0 + 3x Samsung F3 1TB Raid0 Pioneer BD-RW Win7 Ultimate 64 Samsung 24" 2494 + 2x Acer 22" 
KeyboardPowerCaseMouse
G15 Corsair 1000HX HAF 932 Custom Paint G3 
  hide details  
Reply
post #1518 of 6378
Quote:
Originally Posted by izzman View Post
Quick question.

Can I use the OC settings for the 920 to overclock my 930 on the motherboard?

I haven't found a good place to start OCing with this setup and am very inexperienced. I just want a 3.8ghz or so OC.

Thanks
Set you cpu Ratio to 21 and then in essence..yes you can
Main Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 @ 4.2GHz 1.33V Asus P6X58D Ex 5870 Lightning G-Skill Trident (1600MHz) 7-7-7-20 
Hard DriveOptical DriveOSMonitor
80Gb Intel X25-M gen2 + 1Tb samsung F1 Samsung Blu-Ray Windows 7 64 bit Lg 27" Flatron "m2762d" 
KeyboardPowerCaseMouse
Microsoft/Razor Corsair HX 850 Antec 1200 Razor Death Adder 4000Dpi 
Mouse Pad
Roccat Sota 
  hide details  
Reply
Main Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 @ 4.2GHz 1.33V Asus P6X58D Ex 5870 Lightning G-Skill Trident (1600MHz) 7-7-7-20 
Hard DriveOptical DriveOSMonitor
80Gb Intel X25-M gen2 + 1Tb samsung F1 Samsung Blu-Ray Windows 7 64 bit Lg 27" Flatron "m2762d" 
KeyboardPowerCaseMouse
Microsoft/Razor Corsair HX 850 Antec 1200 Razor Death Adder 4000Dpi 
Mouse Pad
Roccat Sota 
  hide details  
Reply
post #1519 of 6378
I have managed to OC my i7 930 D0 in P6X58D Premium @ 3.8Ghz, 4.0Ghz and 4.2Ghz using BCLK 200 (x19, x20 and x21) but the voltages at which I managed to get stable are way higher than those posted by xmisery and others. What is the reason for my CPU to need a higher voltage for the same level of OC?
My CPU Batch is 3001A501, I wonder if that matters. What do you reckon?
I would like to try OC'ing my CPU further but at these vCore voltage levels I just don't feel comfortable doing that.
My Turbo V for 4.0Ghz


and for 4.2Ghz



Any help in getting my OC to run at lower voltages (VCore and QPI/DRAM) or comments from anyone with the same CPU would be much appreciated.
Edited by perkeo - 4/2/10 at 2:51pm
    
CPUMotherboardGraphicsRAM
i7 930 2.8Ghz OC @ 4.00Ghz - Batch 3001A510 ASUS P6X58D Premium Radeon HD 5770 Vapor-X Corsair TR3X6GB1600C8D 3 x 2GB 1600Mhz 8-8-8-24 
Hard DriveOptical DriveOSMonitor
WD Raptor 74GB x 2 in RAID 0 LG Blue Ray reader & burner Windows 7 x64 Samsung SyncMaster P2370 
KeyboardPowerCaseMouse
Logitech Corsair HX850W Thermaltake Armor+ VH6000BWS Logitech 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
i7 930 2.8Ghz OC @ 4.00Ghz - Batch 3001A510 ASUS P6X58D Premium Radeon HD 5770 Vapor-X Corsair TR3X6GB1600C8D 3 x 2GB 1600Mhz 8-8-8-24 
Hard DriveOptical DriveOSMonitor
WD Raptor 74GB x 2 in RAID 0 LG Blue Ray reader & burner Windows 7 x64 Samsung SyncMaster P2370 
KeyboardPowerCaseMouse
Logitech Corsair HX850W Thermaltake Armor+ VH6000BWS Logitech 
  hide details  
Reply
post #1520 of 6378
Quote:
Originally Posted by Jamos169 View Post
Set you cpu Ratio to 21 and then in essence..yes you can

Thank you!
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › [Official] --The Asus P6X58D Premium & E Thread--