Overclock.net › Forums › Intel › Intel Motherboards › [Official] --The Asus P6X58D Premium & E Thread--
New Posts  All Forums:Forum Nav:

[Official] --The Asus P6X58D Premium & E Thread-- - Page 214

post #2131 of 6325
Stable 3.8Ghz HT on i7 930 using xmisery's i7 920@3.8Ghz template. Contrary to other 930 owners, I was able to use a lower VCore. I also enabled Intel Vt-x for VirtualBox. Stability tested using LinX configuration described below. FYI, I was able to OC to 4.2Ghz and 4.0 stable on air but my temps were high. The difference between 3.8 and 4.0 was about 8C and more voltage. Noctua NH-U12P HSF is not performing as well as I expected. I may try remounting with different thermal compound this weekend.



3.8 is the sweet spot for the CPU I have.

i7 930 D0 batch# 3939C198 ordered from Newegg 3 days ago, shipped from CA warehouse

Update
=====
5/29: Increased CPU Voltage 1 notch; decreased IOH Voltage. Now passing ~10 hours of LinX tests

Changes are in red.

Quote:
Originally Posted by xmisery View Post
NOTE: These settings were stable for me and should be for you as well. However, not all i7's are created equal, so YMMV. That said, these settings were tested against LinX - / Problem size: 25854 / Memory to use: 5120 / Times to run: 20. If you guys see some additional tweaks or changes to make this even better, please share.

**************************************
Running 3.80GHz w/ HyperThreading (Stable)
**************************************

Code:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[181]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1451MHz]
UCLK Frequency.........................[2903MHz]
QPI Link Data Rate.....................[Auto]

CPU Voltage Control....................[Manual]
CPU Voltage............................[1.16875 1.14375]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.20000]
IOH Voltage............................[1.14 1.12]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]

Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]

C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled Enabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]

Edited by mgutz - 5/29/10 at 9:36am
WinuxMac
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @ 3.8Ghz, 1.14v Asus P6X58D-E MSI N260GTX OC Corsair Dominator 6GB DDR3 1600 
OSKeyboardPowerCase
Win7 x64, SL 10.6.3, Ubuntu 10.04 Filco Tenkeyless, Cherry Brown Corsair 750W CM HAF 922 + side 20cm fan 
  hide details  
Reply
WinuxMac
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @ 3.8Ghz, 1.14v Asus P6X58D-E MSI N260GTX OC Corsair Dominator 6GB DDR3 1600 
OSKeyboardPowerCase
Win7 x64, SL 10.6.3, Ubuntu 10.04 Filco Tenkeyless, Cherry Brown Corsair 750W CM HAF 922 + side 20cm fan 
  hide details  
Reply
post #2132 of 6325
Quote:
Originally Posted by CPT Ethanolic View Post
Running at idle, I'm noticing that core 1 is always 3-4 degrees higher than the rest (right now = 42, 38, 38, 36). Is this normal? I see it was also the highest peak temp on the overnight Prime95.
Mine is the same. remounting made no change. although my is more like 5-7 degrees diff
1st WC Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @4.5Ghz 1.39v P6X58D Premium Radeon 5850 @850/1200 Cosair Dom 3x2Gb 1600 7-7-7-20 @1290 6-6-6-18 
Hard DriveOptical DriveOSMonitor
Kingston SSD 64Gb V Series ASUS DVDRW Win7 Ultimate x64 Samsung 2233B 
PowerCase
OCZ 600W CM 932 
  hide details  
Reply
1st WC Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @4.5Ghz 1.39v P6X58D Premium Radeon 5850 @850/1200 Cosair Dom 3x2Gb 1600 7-7-7-20 @1290 6-6-6-18 
Hard DriveOptical DriveOSMonitor
Kingston SSD 64Gb V Series ASUS DVDRW Win7 Ultimate x64 Samsung 2233B 
PowerCase
OCZ 600W CM 932 
  hide details  
Reply
post #2133 of 6325
Quote:
Originally Posted by Atlasprime View Post
Hey folks. First round of OC'ing here and its looking... ok...
Im at least able to boot into windows now. Im using Misery's 3.8 as a base.

Current VCore is 1.3
Current QPI/DRAM is 1.275

Getting a 1D stop after only 2 minutes or so :-(

Trying 1.325 Vcore now. Any suggestions. Im also using the 930. seems i shouldve gone with the 920 :-(


Anyone with a 930 and at 4.0 can you hook me up with some bios settings? Would be greatly appreciative.
Check out my settings on previous page (page 209). 930 seems to need more vcore. I'd also look at upping you QPI/DRAM.

For my 4.5 my QPI is just under the vcore

Going above 3.8Ghz usually requires you to modify other voltages. Have you done that yet or are you still sitting on AUTO for everything but vcore and QPI/DRAM?
Edited by xDelx - 5/27/10 at 8:13pm
1st WC Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @4.5Ghz 1.39v P6X58D Premium Radeon 5850 @850/1200 Cosair Dom 3x2Gb 1600 7-7-7-20 @1290 6-6-6-18 
Hard DriveOptical DriveOSMonitor
Kingston SSD 64Gb V Series ASUS DVDRW Win7 Ultimate x64 Samsung 2233B 
PowerCase
OCZ 600W CM 932 
  hide details  
Reply
1st WC Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 D0 @4.5Ghz 1.39v P6X58D Premium Radeon 5850 @850/1200 Cosair Dom 3x2Gb 1600 7-7-7-20 @1290 6-6-6-18 
Hard DriveOptical DriveOSMonitor
Kingston SSD 64Gb V Series ASUS DVDRW Win7 Ultimate x64 Samsung 2233B 
PowerCase
OCZ 600W CM 932 
  hide details  
Reply
post #2134 of 6325
My settings are below. I needed a bit more voltage to get there, but 3.8 GHz is the sweet spot on my chip as well. I stability tested with Linx, OCCT and a 30 hour run on Prime. I tried 4.0 and 4.2, but they both increased heat and required more voltage than I cared to deal with. This chip hit 4.42 but I did not want to attempt to make it stable since it didnt post until I put 1.39 volts to it. I idle at approximately 29C and hit 60C at load, so I am happy with where I am sitting. The chip is batch number 3951A723 and I bought it from Newegg about 3 weeks ago.


Originally made by xmisery:

**************************************
Running 3.80GHz w/ HyperThreading (Stable)
**************************************

Code:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[181]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1451MHz]
UCLK Frequency.........................[2903MHz]
QPI Link Data Rate.....................[Auto]

CPU Voltage Control....................[Manual]
CPU Voltage............................[1.16875] 1.200
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.20000] 1.21875
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]

Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]

C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]

Edited by rattlerskin - 5/27/10 at 9:34pm
Black Beast
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 3770k Gigabyte Z77X-UP5-TH MSI HD7970OC (2xCFX) 2x4GB G.Skill Sniper 1600 MHz 
Hard DriveHard DriveOptical DriveCooling
1 TB WD Caviar Black SATA III 256 GB Samsung 840 Pro Asus Blu Ray Burner Corsair H100i 
OSMonitorPowerCase
Win 7 Home Premium 64 bit Crossover 1440p 27" Corsair HX850 CM HAF 932 
  hide details  
Reply
Black Beast
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 3770k Gigabyte Z77X-UP5-TH MSI HD7970OC (2xCFX) 2x4GB G.Skill Sniper 1600 MHz 
Hard DriveHard DriveOptical DriveCooling
1 TB WD Caviar Black SATA III 256 GB Samsung 840 Pro Asus Blu Ray Burner Corsair H100i 
OSMonitorPowerCase
Win 7 Home Premium 64 bit Crossover 1440p 27" Corsair HX850 CM HAF 932 
  hide details  
Reply
post #2135 of 6325
I am currently running 4.0 with misery settings with a vcore of 1.325 and a qpi a few tenths behind. It stable enough to use for regulsr stuff and lite gaming but bsoded last night after sbout 45 minutes. I dont want to go hier then 1.35 and im not sure if i even need to boost my qpi while i go up in vcore. If this does not work i guess i will have to leave the four ghz club
post #2136 of 6325
Quote:
Originally Posted by CPT Ethanolic View Post
As Medred said below, you can get HT stable at 4.0. I just haven't had enough time, nor inclination, to mess with it.

Honest question for anyone... have any of you seen benchmarks for gaming that show that at over 4.0 Ghz, HT actually enhances things significantly? Everything I read suggested that it's kind of pointless for the extra voltage required.
I would imagine this is true. I dont know of any game other then supreme commander thst would even utilize the extra 4 threads. Ill throw some benches up after work today.
post #2137 of 6325
Quote:
Originally Posted by Atlasprime View Post
I am currently running 4.0 with misery settings with a vcore of 1.325 and a qpi a few tenths behind. It stable enough to use for regulsr stuff and lite gaming but bsoded last night after sbout 45 minutes. I dont want to go hier then 1.35 and im not sure if i even need to boost my qpi while i go up in vcore. If this does not work i guess i will have to leave the four ghz club
Do you have HT turned on? With HT off, you should easily be able to get a stable 4.0 at under 1.3 V core. As pointed out above, I haven't seen any bench marks showing a significant advantage of having HT on and it certainly makes 4.0 tough to get at. With it off, I can get a stable 4.01 at 1.28 V (and could probably drop that more with some toying around).
post #2138 of 6325
with HT off I get to 4.2 changing only CPU Voltage & QPI/DRAM from xmisery's settings to:

CPU Voltage 1.27500
QPI/DRAM 1.30000
Mem timings 8-8-8-24 1T
max core/cpu temps under linx & intelburn test 76c/61c - idle 37c/21c
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 @ 4.0 Ghz Asus P6X58D Premium EVGA GTS 250 X 2 Corsair Dom 1600 1GX3 TR3X3G1600C8D 
Hard DriveOSPowerCase
WD VelociRaptor 300G Win XP 32b Corsair HX1000W CM 690 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 930 @ 4.0 Ghz Asus P6X58D Premium EVGA GTS 250 X 2 Corsair Dom 1600 1GX3 TR3X3G1600C8D 
Hard DriveOSPowerCase
WD VelociRaptor 300G Win XP 32b Corsair HX1000W CM 690 
  hide details  
Reply
post #2139 of 6325
Quote:
Originally Posted by lux View Post
with HT off I get to 4.2 changing only CPU Voltage & QPI/DRAM from xmisery's settings to:

CPU Voltage 1.27500
QPI/DRAM 1.30000
Mem timings 8-8-8-24 1T
max core/cpu temps under linx & intelburn test 76c/61c - idle 37c/21c
Are you running a 920 or 930? If I set Vcore to 1.28, I get BSOD after about 5 minutes in Prime.
post #2140 of 6325
Quick question here that I forgot to add to my post above: What are the names of the settings that I need to modify in the bios to get my timings to 8-8-8-24 from the auto settings of 9-9-9-24? There are a whole bunch of settings there, and I dont know which ones are the correct ones. Also, since my ram is running at 1451 MHz rather than the rated 1600 MHz, is it possible to get my timings to 7-7-7-24 without much headache?
Black Beast
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 3770k Gigabyte Z77X-UP5-TH MSI HD7970OC (2xCFX) 2x4GB G.Skill Sniper 1600 MHz 
Hard DriveHard DriveOptical DriveCooling
1 TB WD Caviar Black SATA III 256 GB Samsung 840 Pro Asus Blu Ray Burner Corsair H100i 
OSMonitorPowerCase
Win 7 Home Premium 64 bit Crossover 1440p 27" Corsair HX850 CM HAF 932 
  hide details  
Reply
Black Beast
(15 items)
 
  
CPUMotherboardGraphicsRAM
i7 3770k Gigabyte Z77X-UP5-TH MSI HD7970OC (2xCFX) 2x4GB G.Skill Sniper 1600 MHz 
Hard DriveHard DriveOptical DriveCooling
1 TB WD Caviar Black SATA III 256 GB Samsung 840 Pro Asus Blu Ray Burner Corsair H100i 
OSMonitorPowerCase
Win 7 Home Premium 64 bit Crossover 1440p 27" Corsair HX850 CM HAF 932 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › [Official] --The Asus P6X58D Premium & E Thread--