Overclock.net › Forums › Cooling › Water Cooling › Confused on how to connect
New Posts  All Forums:Forum Nav:

Confused on how to connect - Page 2

post #11 of 16
Snerps setup is the same as mine,only difference is Tline/Res. And suicide mayne,your crazypc link is a tline,you just route the tubing on either side,and then a tube to the top of the case.
My System
(13 items)
 
  
CPUMotherboardOSKeyboard
AMD Athlon Xp2900 Abit Nf7 Xandros/XP Home Z-Board 
PowerCaseMouse
Antec SmartPower 500W Elegance X-Raider+Ratpadz 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardOSKeyboard
AMD Athlon Xp2900 Abit Nf7 Xandros/XP Home Z-Board 
PowerCaseMouse
Antec SmartPower 500W Elegance X-Raider+Ratpadz 
  hide details  
Reply
post #12 of 16
Alright....PUMP-->RADIATOR-->PRIMARY GPU-->SECONDARY GPU-->T-LINE-->PUMP. Having the T-line between the gpu blocks would restrict your flow too much. If you insist on tubing it that way, use Y fittings...they don't restrict flow as much. Also, sinve you are using 68's, i would reccommend DangerDen NV-68s,,,they woud rectify the flow problem between the vidcards and they are highly efficient.

EDIT: Use a t-line, not a res. They are cheaper and IMO easier to bleed since they do it on the fly. After you first start your setup, leave your T-line elevated and uncovered for @ least 48 ours top bleed the system (while the pump is running of course). http://www.pimprig.com has a great T line makup in their guides that i use myself. Never had a bleeding/filling/spillag problem with it. and it looks really clean, and since i have a mid-tower, it doesn;t eat up the space of a res.
The Overmind
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 920 Gigabyte GA-EX58-UD5 EVGA GTX 280 SLI G.Skill 6GB DDR3 1600MHz 
Hard DriveOptical DriveOSMonitor
Maxtor 500GB SATA, Seagate 1TB, 60GB OCZ Vertex 2 Generic Asus Multiformat Windows 7 RC1 Dell 3007WFP-HC 
KeyboardPowerCaseMouse
Saitek Eclipse Silverstone Decathalon 1000 Watt Antec 900 Microsoft Sidewinder 
Mouse Pad
Spongebob Squarepants Bitch! 
  hide details  
Reply
The Overmind
(13 items)
 
  
CPUMotherboardGraphicsRAM
i7 920 Gigabyte GA-EX58-UD5 EVGA GTX 280 SLI G.Skill 6GB DDR3 1600MHz 
Hard DriveOptical DriveOSMonitor
Maxtor 500GB SATA, Seagate 1TB, 60GB OCZ Vertex 2 Generic Asus Multiformat Windows 7 RC1 Dell 3007WFP-HC 
KeyboardPowerCaseMouse
Saitek Eclipse Silverstone Decathalon 1000 Watt Antec 900 Microsoft Sidewinder 
Mouse Pad
Spongebob Squarepants Bitch! 
  hide details  
Reply
post #13 of 16
Thread Starter 
so a t-Line is like a Res? where u put water? where can i see T-Line products
My System
(13 items)
 
  
CPUMotherboardOSPower
AMD Athlon 4000+ DFI Lanparty SLI-D Windows XP Pro x64 PC Power & Cooling 510 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardOSPower
AMD Athlon 4000+ DFI Lanparty SLI-D Windows XP Pro x64 PC Power & Cooling 510 
  hide details  
Reply
post #14 of 16
Place the T line on the pumps inlet,That allows for easier filling and bleeding.

As far as order of components the "Best" set up is one where you have the least tubing and the least amount of bends,avoid the hype of rad placment,It will only result in a max of 0.5c lower temps and that can not increase performance even 1Mhz..A chip at 37c can not overclock any better then if it was at 37.5c . . So just set it up as eaily and efficiently based on tubing issues.

Also Using Y Fittings reduces flow and should be avoided.And I hope you are using a dual 120mm rad because that will handle 2 GPU and 1 CPU ,I know this from experence running 2 Xeon 2.4 @ 3675 each and a 6800 ultra.
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
1055T @ 3808 ( 272x14) MSI 890CXM-G65 HD5770 8 gigs Crucial 
Hard DriveOSMonitorKeyboard
Kingston SSD 64g XP Pro Viewsonic 19 inch Lcd Memorex 
PowerMouse
ThermalTake 850 Modular Logitech 
  hide details  
Reply
My System
(13 items)
 
  
CPUMotherboardGraphicsRAM
1055T @ 3808 ( 272x14) MSI 890CXM-G65 HD5770 8 gigs Crucial 
Hard DriveOSMonitorKeyboard
Kingston SSD 64g XP Pro Viewsonic 19 inch Lcd Memorex 
PowerMouse
ThermalTake 850 Modular Logitech 
  hide details  
Reply
post #15 of 16
you should take the Ts out because they will slow the flow down.
post #16 of 16
I would think it best to have two seperate loops or at least two rads your gonna have alot of heat in your loop.
LUCKY
(13 items)
 
  
CPUGraphicsHard DriveOS
I5 3570 4890 1 TB WD Windows 7 
MonitorKeyboardPowerCase
Dell 2407 Saitek Eclipse OCZ Powerstream 850 Custom (build log in sig) 
Mouse
MX518 
  hide details  
Reply
LUCKY
(13 items)
 
  
CPUGraphicsHard DriveOS
I5 3570 4890 1 TB WD Windows 7 
MonitorKeyboardPowerCase
Dell 2407 Saitek Eclipse OCZ Powerstream 850 Custom (build log in sig) 
Mouse
MX518 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › Confused on how to connect