Overclock.net › Forums › Intel › Intel Motherboards › * The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club *
New Posts  All Forums:Forum Nav:

* The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club * - Page 103

post #1021 of 3829
Quote:
Originally Posted by dr_dx View Post
NoGuru,

Just FYI the EK only fits rev1. Your best bet is to do what you already did - change the TIM. I suppose there might be an aftermarket chipset cooler that can use 1/2" barbs that might fit the screw pattern.

Since GB reduced the phases down to 16 in the rev2, the layout is different and the EK doesn't fit it. I believe EK mentions this on their website. I suppose if there is enough demand, they may make one for the rev2.
Oh snap, i haven't had time to look at there site. I knew that the one block only fit Rev 1. but just asumed they would make one for Rev 2. That's why they say never asume anything. +rep

@ Alinwere, make sure the blocks are not loose as well, that will stop it from booting.
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
post #1022 of 3829
here is a quick run with out mem tweaking. I will post template in my next post. CPUZ link below shows minimum windows bootable voltage.



Edited by dr_dx - 10/16/10 at 10:59pm
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
post #1023 of 3829
Quote:
Originally Posted by dr_dx View Post
here is a quick run with out mem tweaking - remember this is 12 cores. I will post template in next post. CPUZ link below shows minimum windows bootable voltage.

Nice, but I'm not sure I would say 3 runs is stable.
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
The HedgeHog
(15 items)
 
  
CPUMotherboardGraphicsRAM
3770K Z77-UP7 MSI GTX 680 Twin 4 Gig G.Skill Trident X 2600's and some Dom's Hypers 
Hard DriveCoolingOSMonitor
Yes, lots of them. LN2  The smallest one I can get! Samsung 2333 HD 23" 
PowerCaseMouseMouse Pad
Corisar 1200 AX=1.21 jigawatts Fractal Design/Dimastech G5 Rocketfish 
  hide details  
Reply
post #1024 of 3829
Quote:
Originally Posted by NoGuru View Post
Nice, but I'm not sure I would say 3 runs is stable.
Call it what you want, it's working 100% for me. I have some better RAM on the way; we'll see what happens with it.



Remember: This is 6 cores - not 4.

Code:
GIGABYTE GA-X58A-UD7 rev2

MB Intelligent Tweaker(M.I.T.)

> Advanced Frequency Settings [Press Enter]

CPU Clock Ratio............................:25 
CPU Frequency ........................(GHz):4.5 
> Advanced CPU Core Features [Press Enter]

Intel(R) Turbo Boost Tech..................:Disabled 
CPU Cores Enabled..........................:All 
CPU Multi Threading........................:Enabled 
CPU Enhanced Halt (C1E)....................:Disabled 
C3/C6/C7 State Support.....................:Disabled 
CPU Thermal Monitor........................:Disabled 
CPU EIST Function..........................:Disabled 
Bi-Directional PROCHOT.....................:Disabled 

QPI Clock Ratio............................:x36 
QPI Link Speed........................(GHz):6.48 
Uncore Clock Ratio.........................:Auto [x20] 
Uncore Frequency......................(MHz):3600 
>>>>> Standard Clock Control
Base Clock(BCLK) Control...................:Enabled 
BCLK Frequency(MHz)........................:180 
Extreme Memory Profile(X.M.P.).............:Disabled 
System Memory Multiplier (SPD).............:8 
Memory Frequency(MHz)......................:1440 
PCI Express Frequency(MHz).................:Auto
>>>>> Advanced Clock Control
CPU Clock Drive (mV).......................:800 
PCI Express Clock Drive (mV)...............:900 
CPU Clock Skew (ps)........................:0 
IOH Clock Skew (ps)........................:0 

> Advanced Memory Settings [Press Enter]

Extreme Memory Profile(X.M.P.).............:Disabled 
System Memory Multiplier (SPD).............:8 
Memory Frequency(MHz)......................:1440 
Performance Enhance........................:Standard 
DRAM Timing Selectable (SPD)...............:Auto 
Profile DDR Voltage........................: 
Profile QPI Voltage........................: 
Channel Interleaving.......................: 
Rank Interleaving..........................: 
>>>>> Channel A, B, & C
> Channel A, B, & C Timing Settings [Press Enter]

>>>>> Channel A, B, & C Standard Timing Control
Cas Latency Time...........................: 
tRCD.......................................: 
tRP........................................: 
tRAS.......................................: 
>>>>> Channel A, B, & C Advanced Timing Control
tRC........................................: 
tRRD ......................................: 
tWTR ......................................: 
tWR........................................: 
tWTP.......................................: 
tWL........................................: 
tRFC.......................................: 
tRTP.......................................: 
tFAW.......................................: 
Command Rate (CMD) ........................: 
>>>>> Channel A, B, & C Misc Timing Control
B2B CAS Delay..............................: 
Round Trip Latency.........................: 

> Channel A, B, & C Turnaround Setting [Press Enter]

>>>>> Channel A, B, & C Reads Followed By Reads
Different DIMMs............................: 
Different Ranks............................: 
On The Same Rank...........................: 
>>>>> Channel A, B, & C Writes Followed By Writes
Different DIMMs............................: 
Different Ranks............................: 
On The Same Rank...........................: 

> Advanced Voltage Settings [Press Enter]

>>> CPU
LoadLine Calibration.......................:L2 
CPU Vcore..................................:1.43125 
xDynamic Vcore(DVID).......................:0.0000 
QPI/VTT Voltage............................:Auto 
CPU PLL....................................:Auto 
>>> MCH/ICH
PCIE.......................................:Auto 
QPI PLL....................................:Auto 
IOH Core...................................:Normal 
ICH I/O....................................:Auto 
ICH Core...................................:Auto 
>>> Dram
DRAM Voltage...............................:1.5 
DRAM Termination...........................:Auto 
Ch-A Data VRef.............................:Auto 
Ch-B Data VRef.............................:Auto 
Ch-C Data VRef.............................:Auto 
Ch-A Address VRef..........................:Auto 
Ch-B Address VRef..........................:Auto 
Ch-C Address VRef..........................:Auto 

> Miscellaneous Settings [Press Enter]

Isochronous Support........................:Enabled 
Virtualization Technology..................:Enabled


GOOC Lean Mode.............................:ON
GOOC extreme clock.........................:Enabled
GOOC extreme temp..........................:Disabled 

Edited by dr_dx - 10/16/10 at 11:00pm
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
post #1025 of 3829
screen shot attached. After new mem comes, will work on tweaking it some more.

Hopefully this qualifies me for the owner's club...


Code:
GIGABYTE GA-X58A-UD7 rev2 6core 4.6Ghz

MB Intelligent Tweaker(M.I.T.)

> Advanced Frequency Settings [Press Enter]

CPU Clock Ratio............................:23 
CPU Frequency ........................(GHz):4.6 
> Advanced CPU Core Features [Press Enter]

Intel(R) Turbo Boost Tech..................:Disabled 
CPU Cores Enabled..........................:All 
CPU Multi Threading........................:Enabled 
CPU Enhanced Halt (C1E)....................:Disabled 
C3/C6/C7 State Support.....................:Disabled 
CPU Thermal Monitor........................:Disabled 
CPU EIST Function..........................:Disabled 
Bi-Directional PROCHOT.....................:Disabled 

QPI Clock Ratio............................:x36 
QPI Link Speed........................(GHz):7.2 
Uncore Clock Ratio.........................:Auto [x19] 
Uncore Frequency......................(MHz):3800 
>>>>> Standard Clock Control
Base Clock(BCLK) Control...................:Enabled 
BCLK Frequency(MHz)........................:200 
Extreme Memory Profile(X.M.P.).............:Disabled 
System Memory Multiplier (SPD).............:8 
Memory Frequency(MHz)......................:1600 
PCI Express Frequency(MHz).................:100
>>>>> Advanced Clock Control
CPU Clock Drive (mV).......................:800 
PCI Express Clock Drive (mV)...............:900 
CPU Clock Skew (ps)........................:0 
IOH Clock Skew (ps)........................:0 

> Advanced Memory Settings [Press Enter]

Extreme Memory Profile(X.M.P.).............:Disabled 
System Memory Multiplier (SPD).............:8 
Memory Frequency(MHz)......................:1600 
Performance Enhance........................:Standard 
DRAM Timing Selectable (SPD)...............:Auto 
Profile DDR Voltage........................: 
Profile QPI Voltage........................: 
Channel Interleaving.......................: 
Rank Interleaving..........................: 
>>>>> Channel A, B, & C
> Channel A, B, & C Timing Settings [Press Enter]

>>>>> Channel A, B, & C Standard Timing Control
Cas Latency Time...........................: 
tRCD.......................................: 
tRP........................................: 
tRAS.......................................: 
>>>>> Channel A, B, & C Advanced Timing Control
tRC........................................: 
tRRD ......................................: 
tWTR ......................................: 
tWR........................................: 
tWTP.......................................: 
tWL........................................: 
tRFC.......................................: 
tRTP.......................................: 
tFAW.......................................: 
Command Rate (CMD) ........................: 
>>>>> Channel A, B, & C Misc Timing Control
B2B CAS Delay..............................: 
Round Trip Latency.........................: 

> Channel A, B, & C Turnaround Setting [Press Enter]

>>>>> Channel A, B, & C Reads Followed By Reads
Different DIMMs............................: 
Different Ranks............................: 
On The Same Rank...........................: 
>>>>> Channel A, B, & C Writes Followed By Writes
Different DIMMs............................: 
Different Ranks............................: 
On The Same Rank...........................: 

> Advanced Voltage Settings [Press Enter]

>>> CPU
LoadLine Calibration.......................:L2 
CPU Vcore..................................:1.4875 
xDynamic Vcore(DVID).......................:0.0000 
QPI/VTT Voltage............................:1.495 
CPU PLL....................................:Auto 
>>> MCH/ICH
PCIE.......................................:Auto 
QPI PLL....................................:Auto 
IOH Core...................................:Normal 
ICH I/O....................................:Auto 
ICH Core...................................:Auto 
>>> Dram
DRAM Voltage...............................:1.5 
DRAM Termination...........................:Auto 
Ch-A Data VRef.............................:Auto 
Ch-B Data VRef.............................:Auto 
Ch-C Data VRef.............................:Auto 
Ch-A Address VRef..........................:Auto 
Ch-B Address VRef..........................:Auto 
Ch-C Address VRef..........................:Auto 

> Miscellaneous Settings [Press Enter]

Isochronous Support........................:Enabled 
Virtualization Technology..................:Disabled


GOOC Lean Mode.............................:ON
GOOC extreme clock.........................:Enabled
GOOC extreme temp..........................:Disabled 



Edited by dr_dx - 10/16/10 at 11:01pm
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
MVF
(4 items)
 
  
CPUMotherboardGraphicsRAM
i7-3770K MAXIMUS V FORMULA AMD Radeon HD 7900 Series G Skill Trident X 2x8Gb DDR3 2400 
  hide details  
Reply
post #1026 of 3829
Hey guys, I have Rev. 1.0 Full board block from EK for sale here if anyone is interested!
http://www.overclock.net/cooling-pro...ull-board.html

It's the EK FB UD7 Nickel/Plexi.

@ Alienware, you need to tighten the screws in HARD, and even then it is still a kinda loose fit. You will see once you remove your block, I bet there is no contact with your paste.

I contacted EK about this and they didn't believe me or thought I was doing it wrong, since that time I've noticed SEVERAL people say the same thing. Some use more paste than normal, others sand down the spacers a bit, either way it is not a really tight fit unless you screw it down hard and even then it may not be.

This is probably not your issue though, I started mine with no contact and the board started fine. So for now you should put back on your stock heatpipe and see if the board starts, if it does not you have other issues and may need to update the BIOS with a 920, or something else may be wrong such as a short in your case or something.

Be sure you have the memory in the white slots, and that you are using a known compatible PSU for this board.
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
post #1027 of 3829
Quote:
Originally Posted by lsdmeasap View Post
Hey guys, I have Rev. 1.0 Full board block from EK for sale here if anyone is interested!
...
So, shall we assume that you give up your legendary rev.1 UD7?
My System
(14 items)
 
  
CPUMotherboardGraphicsRAM
I7 960 GA-X58A-UD7 rev.1 (NB wc) 2x Sapphire HD7970 (wc) 3x 4GB Dominator GT 2000CL9 @1866CL8 
Hard DriveCoolingOSMonitor
INTEL X-25M 160GB / BARRACUDA XT 2TB CPU-370 (wc) Windows 7 64bit Ultimate LG 2486L-PF 
KeyboardPowerCaseMouse
Logitech G15 Enermax Revolution85+ 1250w COSMOS Pure Razor 
  hide details  
Reply
My System
(14 items)
 
  
CPUMotherboardGraphicsRAM
I7 960 GA-X58A-UD7 rev.1 (NB wc) 2x Sapphire HD7970 (wc) 3x 4GB Dominator GT 2000CL9 @1866CL8 
Hard DriveCoolingOSMonitor
INTEL X-25M 160GB / BARRACUDA XT 2TB CPU-370 (wc) Windows 7 64bit Ultimate LG 2486L-PF 
KeyboardPowerCaseMouse
Logitech G15 Enermax Revolution85+ 1250w COSMOS Pure Razor 
  hide details  
Reply
post #1028 of 3829
Hey Guys, just how efficient is the (included) waterblock for cooling the NB on the UD7 rev 2 board over air cooling it? Is there a huge difference? the reason I ask is because of the fins on the block...
Edited by LaZyBoneS - 10/16/10 at 4:10am
Beats The TV
(13 items)
 
  
CPUMotherboardGraphicsRAM
I7 965 extreme @4.2Ghz GA-X58A-UD7 rev2 evga GTX 295 dual pcb ver Corsair Dominator GT 2000 6g 
Hard DriveOptical DriveOSMonitor
OCZ vertex 2 SSD's 60g x 2 Asus DVD RW Win 7 64bit Ultimate Samsung 2493HM 24" 
KeyboardPowerCaseMouse
Logitech G15 corsair 1200w Coolermaster HAF X Logitech G9 
  hide details  
Reply
Beats The TV
(13 items)
 
  
CPUMotherboardGraphicsRAM
I7 965 extreme @4.2Ghz GA-X58A-UD7 rev2 evga GTX 295 dual pcb ver Corsair Dominator GT 2000 6g 
Hard DriveOptical DriveOSMonitor
OCZ vertex 2 SSD's 60g x 2 Asus DVD RW Win 7 64bit Ultimate Samsung 2493HM 24" 
KeyboardPowerCaseMouse
Logitech G15 corsair 1200w Coolermaster HAF X Logitech G9 
  hide details  
Reply
post #1029 of 3829
Quote:
Originally Posted by ElGreco View Post
So, shall we assume that you give up your legendary rev.1 UD7?
Na, just sold one is all. Still have another
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
Intel i7 980X EE ES Gigabyte GA-X58A-UD7 GIGABYTE GV-R587SO-1GD SOC 1GB GDDR5 Mushkin 998826 Ridgeback / 998966 Radioactive 
OSMonitorPower
Vista Business x64 SP2 Asus Designo MS238H 23" LED NZXT HALE90 750W 80+ GOLD 
  hide details  
Reply
post #1030 of 3829
Quote:
Originally Posted by dr_dx View Post
...remember this is 12 cores....
Quote:
Originally Posted by dr_dx View Post
...Remember: This is 12 cores...
Quote:
Originally Posted by dr_dx View Post
Code:
...12core...
dr_dx, what are you trying to say and/or prove with the multiple "12 cores" statements? Also, your BIOS posting template is altered and not completely filled out.
Edited by MacG32 - 10/16/10 at 1:55am
Under The Radar
(17 items)
 
  
CPUMotherboardGraphicsRAM
AMD - Ryzen 7 1800X Gigabyte - GA-AX370-Gaming K7 Gigabyte - GeForce GTX 1080 Ti 11GB FE G.Skill - Flare X 32GB (4 x 8GB) DDR4-3200 
Hard DriveHard DriveOptical DriveCooling
Samsung - 850 Pro 512GB 2.5" SSD Western Digital - Black 6TB 3.5" 7200RPM HDD Asus - BW-12B1ST/BLK/G/AS Blu-Ray/DVD/CD Writer Corsair - H115i 104.7 CFM Liquid CPU Cooler 
OSMonitorMonitorKeyboard
Microsoft - Windows 10 Pro OEM 64-bit Acer - GN246HL 24" 1080p 144Hz Acer - G246HLAbd 24" 1080p 60Hz Ducky - Shine 4 
PowerCaseMouseMouse Pad
EVGA - SuperNOVA P2 650W 80+ Platinum Certified... Corsair - Vengeance C70 (Black) ATX Mid Tower Cooler Master - Xornet Fellowes - Microban 
Audio
2 x Realtek - ALC1220 2 - 7.1 Channel High Defi... 
  hide details  
Reply
Under The Radar
(17 items)
 
  
CPUMotherboardGraphicsRAM
AMD - Ryzen 7 1800X Gigabyte - GA-AX370-Gaming K7 Gigabyte - GeForce GTX 1080 Ti 11GB FE G.Skill - Flare X 32GB (4 x 8GB) DDR4-3200 
Hard DriveHard DriveOptical DriveCooling
Samsung - 850 Pro 512GB 2.5" SSD Western Digital - Black 6TB 3.5" 7200RPM HDD Asus - BW-12B1ST/BLK/G/AS Blu-Ray/DVD/CD Writer Corsair - H115i 104.7 CFM Liquid CPU Cooler 
OSMonitorMonitorKeyboard
Microsoft - Windows 10 Pro OEM 64-bit Acer - GN246HL 24" 1080p 144Hz Acer - G246HLAbd 24" 1080p 60Hz Ducky - Shine 4 
PowerCaseMouseMouse Pad
EVGA - SuperNOVA P2 650W 80+ Platinum Certified... Corsair - Vengeance C70 (Black) ATX Mid Tower Cooler Master - Xornet Fellowes - Microban 
Audio
2 x Realtek - ALC1220 2 - 7.1 Channel High Defi... 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › * The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club *