Overclock.net › Forums › Intel › Intel Motherboards › * The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club *
New Posts  All Forums:Forum Nav:

* The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club * - Page 367

post #3661 of 3836
Quote:
Originally Posted by TLCH723 View Post


Just out of curiosity, have you stress test your CPU at stock and mentest??

I just ran memtest and no errors were found, only ran 1 pass though.
Quote:
Originally Posted by gofasterstripes View Post

If you have the right BIOS it's should just work. Are you on the last BIOS or the last Beta BIOS (cant check stuff right now)?

I'm currently running F6 BIOS, I tried the two latest beta versions, F7J and F8A, but they wouldn't boot if I changed any overclock settings from auto.
post #3662 of 3836
I have the ud3r and x5650. I have no problem at all with the latest BIOS.
Of course it is different than the ud5.

Try prime95 overnight at stock.
The ratio uncore/memory multiplier is from 1.5x to 2.0x
post #3663 of 3836
@kap62

Here is my BIOS settings for 4GHz and 3200MHz uncore, RAM at stock.

See if anything catches your eye...
post #3664 of 3836
Quote:
Originally Posted by gofasterstripes View Post

@kap62

Here is my BIOS settings for 4GHz and 3200MHz uncore, RAM at stock.

See if anything catches your eye...

Thanks, I noticed a couple differences...

CPUID matches but update revision on mine is 0F instead of 14, not sure that that means anything though

Under advanced clock control:
CPU Clock Drive defaulted to 700mV, you have 800mV
PCI Express Clock Drive defaulted to 700mV, you have 900mV

What are these? Should I raise them?

Other than that, C3/C6/C7 State support defaulted to disabled and you have tighter RAM timings but neither of those should matter.
post #3665 of 3836
You can try adjusting the clock drives, they should certainly be safe for testing. I seem to have set them to ensure the motherboard's stability at 200BClk

Also - you said you have to reset the CMOS to recover - this board shouldn't do that - it has dual BIOS.

EDIT - are you sure your 3.3v battery is good?

EDIT EDIT - Try with all c-states on and turbo off. Set the volts to mine and bring the BCLK up 10 at a time from stock. You may wish to adjust the Uncore ratio....

Good luck, i'll check in tomorrow.
Edited by gofasterstripes - 8/7/16 at 3:28pm
post #3666 of 3836
Quote:
Originally Posted by gofasterstripes View Post

You can try adjusting the clock drives, they should certainly be safe for testing. I seem to have set them to ensure the motherboard's stability at 200BClk

Also - you said you have to reset the CMOS to recover - this board shouldn't do that - it has dual BIOS.

EDIT - are you sure your 3.3v battery is good?

EDIT EDIT - Try with all c-states on and turbo off. Set the volts to mine and bring the BCLK up 10 at a time from stock. You may wish to adjust the Uncore ratio....

Good luck, i'll check in tomorrow.

The CMOS battery metered at 3.166V so it should still be good.

I tried using your settings for the clock drives and it didn't change anything, still wouldn't boot after changing the uncore multiplier. c-states and turbo set like yours didn't change anything either.

When it fails to boot, the debug LED loops between C1 and at least one other value that is too quick to read. Could the looping be keeping the backup BIOS from taking over? I have no idea what they use to determine when the backup BIOS should run. (That is the correct link for my board, got the model and revision off of the board)

EDIT - Tried all settings matching yours, except BCLK at default of 133 and it still wouldn't boot, same C1 loop
Edited by kap62 - 8/7/16 at 4:22pm
post #3667 of 3836
On the UD7 Rev 1 a C1 Debug code is:

[yes that's a R2 manual but I just looked at the R1 as well]

This makes me think we should check the memory situation - maybe try one stick of RAM, ensure your "Performance Enhance" BIOS setting is on standard and manually set your timings. Ensure "Command Rate" is on 2t as well.
Edited by gofasterstripes - 8/8/16 at 12:43am
post #3668 of 3836
Hello guys,ı'm using ga x58a ud7 rev1.0 with i7 930 / 3.6ghz oc
today my xeon e5640 come and i replaced i7 930. but ı have a problem,here is the video https://sendvid.com/jnoveeb6
no bios screen,looping on off. sorry for bad English,can you help me ?

edit:is this cpu deformed ? http://imgur.com/a/yjUFT
Edited by Cyberpunk2077 - 8/8/16 at 9:46am
post #3669 of 3836
Which BIOS are you running?
post #3670 of 3836
Quote:
Originally Posted by gofasterstripes View Post

Which BIOS are you running?
forgot to say, bios f9a
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel Motherboards
Overclock.net › Forums › Intel › Intel Motherboards › * The "Official" Gigabyte GA-X58A-UD3R/UD5/UD7/UD9 Owner's Club *