Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Corsair Graphite Club [780T/760T/730T/600T/380T/230T]
New Posts  All Forums:Forum Nav:

[Official] Corsair Graphite Club [780T/760T/730T/600T/380T/230T] - Page 570

post #5691 of 18197
Exactly like this,
http://www.youtube.com/watch?v=lI7CpHLkJoo
post #5692 of 18197
Quote:
Originally Posted by jl114 View Post

Exactly like this,
http://www.youtube.com/watch?v=lI7CpHLkJoo

that sounds like an optical drive whine, not a fan.. but i could be wrong, have you tried starting the PC with no power to your CD drive? these fans dont have the RPMs to make that type of noise to my knowledge =/
post #5693 of 18197
Quote:
Originally Posted by jl114 View Post

Exactly like this,
http://www.youtube.com/watch?v=lI7CpHLkJoo

That sound happens when u take off the front grill. The only way of getting rid of that sound is either to cut a whole in the mesh of the case or put the front grill back on.
post #5694 of 18197
I'm planning on getting a 600t sometime within the next couple of months and I have an H100. I've been looking through the thread and it seems like most people are having trouble getting a push pull config to work in this case.

Would it possibly work with the two 120mm fans on the top of the case (under the mesh), case, then the rad and then two 120mm 12mm slim fans like these: http://ncix.ca/products/?sku=67371&vpn=SY1212SL12H&manufacture=Scythe

since it barely doesn't fit with two 120mm 25mm fans on the bottom what if you used two 12mm thick fans instead?
post #5695 of 18197
Jl114 see my post # 5103
post #5696 of 18197
Quote:
Originally Posted by Fatality_ View Post

I'm planning on getting a 600t sometime within the next couple of months and I have an H100. I've been looking through the thread and it seems like most people are having trouble getting a push pull config to work in this case.
Would it possibly work with the two 120mm fans on the top of the case (under the mesh), case, then the rad and then two 120mm 12mm slim fans like these: http://ncix.ca/products/?sku=67371&vpn=SY1212SL12H&manufacture=Scythe
since it barely doesn't fit with two 120mm 25mm fans on the bottom what if you used two 12mm thick fans instead?

I have this setup right now, but it is all depending on which motherboard you have. Some MOBOs require that you cut the fan shrouds to fit them in there, others require that you cut the tabs off of your CPU 8pin power connector.

I had to actually offset one fan so that it could give clearance to the heatpipe from my VRMs.
 
The Lil Llano
(12 items)
 
 
CPUMotherboardGraphicsRAM
Intel I7-3930k C-2 ASrock Extreme9 X79 EVGA GTX570 HD Muskin Redline 993997 
Hard DriveHard DriveOptical DriveCooling
OCZ Agility 3 Dell Constilation 7200rpm 6gbps LITE-ON 20X DVD±R DVD Burner Black SATA Model i... Corsair H100 
CoolingCoolingCoolingOS
Coolermaster Excalibur (x4) Coolermaster Turbine (x4) Bitfenix 200mm Spectre Pro  Windows 7 Ultimate 
MonitorMonitorKeyboardPower
24" Sammy 23" Asus Logitech G15 Coolermaster Silent Pro 1300w 
CaseMouseMouse PadAudio
Corsair 600t Logitech MX518 Razer Vespula Dual Sided  Creative 3d Game Blaster 
CPUMotherboardGraphicsRAM
AMD A4-3300 Llano ASRock A55M-HVS FM1 AMD A55 AMD Radeon HD 6410D G.SKILL Ripjaws X Series 
Hard DriveOptical DriveCoolingOS
Western Digital Caviar Blue WD5000AAKS SAMSUNG 22X DVD Burner SATA Model SH-222BB/BEBE Stock Windows XP 
KeyboardPowerCaseMouse
Logitech K400 275w APEX DM-318 Black Steel Micro ATX Logitech K400 
  hide details  
Reply
 
The Lil Llano
(12 items)
 
 
CPUMotherboardGraphicsRAM
Intel I7-3930k C-2 ASrock Extreme9 X79 EVGA GTX570 HD Muskin Redline 993997 
Hard DriveHard DriveOptical DriveCooling
OCZ Agility 3 Dell Constilation 7200rpm 6gbps LITE-ON 20X DVD±R DVD Burner Black SATA Model i... Corsair H100 
CoolingCoolingCoolingOS
Coolermaster Excalibur (x4) Coolermaster Turbine (x4) Bitfenix 200mm Spectre Pro  Windows 7 Ultimate 
MonitorMonitorKeyboardPower
24" Sammy 23" Asus Logitech G15 Coolermaster Silent Pro 1300w 
CaseMouseMouse PadAudio
Corsair 600t Logitech MX518 Razer Vespula Dual Sided  Creative 3d Game Blaster 
CPUMotherboardGraphicsRAM
AMD A4-3300 Llano ASRock A55M-HVS FM1 AMD A55 AMD Radeon HD 6410D G.SKILL Ripjaws X Series 
Hard DriveOptical DriveCoolingOS
Western Digital Caviar Blue WD5000AAKS SAMSUNG 22X DVD Burner SATA Model SH-222BB/BEBE Stock Windows XP 
KeyboardPowerCaseMouse
Logitech K400 275w APEX DM-318 Black Steel Micro ATX Logitech K400 
  hide details  
Reply
post #5697 of 18197
Quote:
Originally Posted by Fatality_ View Post

I'm planning on getting a 600t sometime within the next couple of months and I have an H100. I've been looking through the thread and it seems like most people are having trouble getting a push pull config to work in this case.
Would it possibly work with the two 120mm fans on the top of the case (under the mesh), case, then the rad and then two 120mm 12mm slim fans like these: http://ncix.ca/products/?sku=67371&vpn=SY1212SL12H&manufacture=Scythe
since it barely doesn't fit with two 120mm 25mm fans on the bottom what if you used two 12mm thick fans instead?

Just buy really good quality fans so that it won't make a huge difference in temps without the push/pull configuration. Tom Logan over at Overclock3D says the difference is only a few degrees. Most people just run the fans under the mesh and don't have any temp issues. It'll also look cleaner without the fans pushing air as it won't look cluttered.
The Fortress
(17 items)
 
Black Mamba
(14 items)
 
The Black Pearl
(25 items)
 
CPUMotherboardGraphicsRAM
Intel Core i3 4130 Gigabyte B85M-D3H Sapphire HD6950 1GB 8 GB of Corsair Vengeance lp  
Hard DriveCoolingOSMonitor
Samsung 840 Evo 120GB Intel Stock Cooler Windows 8.1 64 Bit LG 24EN43VS-B 
KeyboardPowerCaseMouse
Logitech K350 Seasonic G-Series 550W  Silverstone PS07B Logitech M510 
Mouse PadAudio
Corsair MM200 Compact Harmon Kardon 2.1 Audio 
  hide details  
Reply
The Fortress
(17 items)
 
Black Mamba
(14 items)
 
The Black Pearl
(25 items)
 
CPUMotherboardGraphicsRAM
Intel Core i3 4130 Gigabyte B85M-D3H Sapphire HD6950 1GB 8 GB of Corsair Vengeance lp  
Hard DriveCoolingOSMonitor
Samsung 840 Evo 120GB Intel Stock Cooler Windows 8.1 64 Bit LG 24EN43VS-B 
KeyboardPowerCaseMouse
Logitech K350 Seasonic G-Series 550W  Silverstone PS07B Logitech M510 
Mouse PadAudio
Corsair MM200 Compact Harmon Kardon 2.1 Audio 
  hide details  
Reply
post #5698 of 18197
Here's my rig. Yes there is some work yet to do on it:

700
post #5699 of 18197
Quote:
Originally Posted by rctrucker View Post

I have this setup right now, but it is all depending on which motherboard you have. Some MOBOs require that you cut the fan shrouds to fit them in there, others require that you cut the tabs off of your CPU 8pin power connector.
I had to actually offset one fan so that it could give clearance to the heatpipe from my VRMs.
Quote:
Originally Posted by Branish View Post

Just buy really good quality fans so that it won't make a huge difference in temps without the push/pull configuration. Tom Logan over at Overclock3D says the difference is only a few degrees. Most people just run the fans under the mesh and don't have any temp issues. It'll also look cleaner without the fans pushing air as it won't look cluttered.

I could just get a couple Noctua NF-P12-1300, Put them on the top and have them exhaust to have a pull only configuration.

Do you guys know if the 650D suffers with this problems as well? Because the cases are similarly priced so I could go with either one but I do really like the look of this one so I am leaning towards getting it.
post #5700 of 18197
Quote:
Originally Posted by dustin88 View Post

that sounds like an optical drive whine, not a fan.. but i could be wrong, have you tried starting the PC with no power to your CD drive? these fans dont have the RPMs to make that type of noise to my knowledge =/

I wish that was the case! Unfortunately I unplugged the fan and it is definitely the culprit of all the noise the tower is making.
Quote:
Originally Posted by franky100 View Post

That sound happens when u take off the front grill. The only way of getting rid of that sound is either to cut a whole in the mesh of the case or put the front grill back on.

Putting the front mesh definitely mutes it a little but at max settings, it is just too unbearable for me.
Quote:
Originally Posted by AirStink View Post

Jl114 see my post # 5103

That is what I was looking to do, long screw with 1-2 nuts inbetween the fan + mesh for spacing, and I guess securing it with another nut would work. What screws did you use? 5mm?
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Computer Cases
Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Corsair Graphite Club [780T/760T/730T/600T/380T/230T]