[Official] Corsair Graphite Club - Page 98

I should be getting the case by this coming Friday, I will make sure I take pics and post them here, so keep an eye out.

My 600T and HX850 comes in on Tuesday. Smack dab in the middle of my finals week.
Don't matter as I have yet to select a P67 board and memory for my 2600K.
Edited by FullMetalZero - 4/30/11 at 9:46pm

I have a Problem. I just Put my setup together. and my Northbridge on my Asus Formula IV is super hot. and The HW monitor isnt reading any type of TEMPs. at all. Im using the 1090T???

Can anyone help? Turned off ACC and Core Unlocker too... Still nothing...

Was there a problem with 1090Ts and Crosshair Formula IVs?

Darn that evil dust!

DUST! I say this to you, Stop being so darned evil!!!!

Sad news about your connector. You know, those are replaceable. Remove the entire controller/connector board and look for a jack on the 'net. I'm sure you should be able to find one. Desolder the broken one and solder on a new one. Use a good solder-sucker and it should be no problem. At the same time you can find the MOSFET that is likely used to alter the speed of the fans. The odds are good it's shorted. I bet you can find it on the 'net too, perhaps at the same place. If not, give me the number off of the package and I'll try and find a sub for you (you can likely find one yourself, but you may have to look through a few datasheets). You can use the same solder sucker to remove it from the pcb.

I'm really surprised Corsair wouldn't have the entire front panel board available as a part. Have you emailed them? Maybe Corsair George can let us know?

Spent the entire weekend so far building a new desk, tearing apart three computer setups and rearranging them, and helping another friend move in. Dog tired......

I grabbed one of those NZXT 200mm fans like the ones you are using. I hope to get a little better flow through the case. I'm looking into adding some blue LEDs to it, but I'm not sure I can.

@longroadtrip

That's a great job you did on that mod.

@tsxboy

When I saw that picture, it was classic Mike Myers in Wayne's World: "Shwing!".
Edited by Mergatroid - 5/1/11 at 2:25am

I have the same setup and it works fine. Download speedfan and see your temps there.

I did encounter a problem where temp 3 says i have -128 c which is im guessing somekind of bug so on speedfan i just hid it. Also download the 4.44 beta works better imo

erm shouldent be a problem afaik could rma the board..

I just bought a 600t special edition white off newegg along with a H60, I was curious to know if the built in fan controller would work with any other fans beside the stock ones? I thought I read somewhere that the fan controller only works with the corsair stock fans, but has the option for up to four fans.

Thanks in advance

I just ordered the 600T SE from NewEgg as well and I can tell you that the case's built in fan controller does work with other brands of fans. But you can only control up to 4 fans in total, at only about 15w each. Which limits you greatly on the fans you can use. Always before you buy check how many watts the fan draws. Or do what I am doing and get an after market fan controller.

I am getting one that fits in a 5.25 drive bay. It has 5 channels and can go up to 60w per channel which raises the choice of fans you can use greatly. Here is a link to the fan controller I am getting.

http://www.frozencpu.com/products/77...?tl=g34c17s286

-Flash

-No Flash




Mad that The Thermaltake frio would seat over my Dominator Gts. And Made me run to Microcenter to buy a H60 to try it out since it was 50 bucks with my friend employee Discount. Mad because temps suck.



My DDR2 4gb 1066 Dominator came in the Mail today. Addition to my other 4gb 1066 Dominator with the old Airflow fan... This is my Guest computer. Needs another 600T SE... Cable is Ugly...

Should I run 2 Coolermaster Sickleflow 2000RPM Black and Red top exhaust and Red Cathodes along the Bottom? I need Opinions.






Thats temps when I just started the computer up within 15minutes (AT IDLE browsing Overclock.net) and Snapped some pictures. Kinda disappointed from the Temps with my other boards and 965BE and 555BE.... Especially with the H60 Push and Pull Setup...


This is Overclocked to 3.7ghz with Turbo on Auto. Dont know if its going to turbo any higher or what. I kinda dont get it... All I did was raise the FSB and Multiplier. Didnt mess with Voltage... Ran a OCCT LIN Test for 2 hours last night CPU temp was at 69C and Cpu Core Temps never rose above 57c... This is overclocked...

H60?
Motherboard NB and SB Heat????

People with Asus Crosshair Formula IV. Are you able to touch your NB and SB Heatsinks without saying "OUCH thats HOT" Because Mine, I cant even leave my finger on there for more than 5 seconds without it starting to Burn...


Please any Input would be greatly appreciated... I dont want to RMA my Board. If you have any Idea's please let me know. I just bought this board on March 13th. I think its the New batch with the Fixed NB and SB standoffs on the Heatsink being Uneven. All you CHF4's 1090T owners please Chime in thanks.
Edited by tsxboy - 5/1/11 at 1:16pm

Hey man I just did a Side By side Snapshot. Mine is way higher temps than yours.. Did you fixed you Standoffs on the NB and SB? did you reapply some Thermal Grease? Let me know.. Kinda weird. because we do have the Same setup.