Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Case Labs Owners Club
New Posts  All Forums:Forum Nav:

[Official] Case Labs Owners Club - Page 1414

post #14131 of 22275
Quote:
Originally Posted by TheCautiousOne View Post

I am not here to make it easy wink.gif

Just to give you a hard time.

TCO
Why did you go from soft tubing to Copper in your log?

I'm using 1/2" soft because I can buy it local for short money.
Quote:
Originally Posted by rioja View Post

Great! So it is 2.75'', right?

This is why you made offset? UT60 has 5.66'' width, so half width is 2.83". It was a liitle wider.

Exactly plus, I wanted to use as much of the factory cut out.
post #14132 of 22275
Quote:
Originally Posted by kgtuning View Post

I'm using 1/2" soft because I can buy it local for short money.

But don't you have copper now?

TCO
     
CPUMotherboardGraphicsGraphics
I7 5930K @ 4.5Ghz Asus Rampage V  GTX 980  GTX 980 
RAMRAMHard DriveHard Drive
Corsair Dominator Platinum 2666mhz DDR4 4 Gb Q... Dominator Light Bar Kits x 2 Crucial 240 SSD  Seagate 7200 Rpm Baracuda 
Hard DriveHard DriveHard DriveCooling
Seagate 7200 Rpm Baracuda Crucial M500 512 SSD Crucial M500 480 SSD EK 480mm Coolstream XTX x 2 
CoolingCoolingCoolingCooling
Tons of Fittings Supremacy Evo Copper EK  XSPC 240mm Radiator V3 x 2 Swiftech MCP35X PMW Pump DDC x 2 
CoolingCoolingCoolingCooling
EK Rampage V Mosfet WaterBlock Original CSQ NB Eloops B12 - 2 1300rpm  Phobia 8way 4pin Fan Controller x 2 Ek Single Link CSQ Bridge x 2 
CoolingCoolingCoolingCooling
Bitspower Z Tank (Clear) 250mm x 2 980 WaterBlocks x 2 Ek DDC Pump Top (Acrylic) x 2 Primochill 3/8" x 1/2" OD Clear Tubing 
CoolingCoolingOSMonitor
Bitspower 12mm Acyrlic Tubing 19" x 4  XSPC 3/8" x 1/2" Compression Fittings x 12 Windows 7 Professional 64 Bit Crossover 324K 
MonitorPowerCaseOther
Qnix 2710 Perfect Pixel 1440p  EVGA 1300 G2 CaseLabs SMA8 Darkside 12" Led Lighting  
CPUMotherboardGraphicsRAM
i7 7700k Asus Strix Z270i Gaming GALAX 980TI HOF Corsair Dominator Platinum DDR4 2400  
Hard DriveCoolingCoolingCooling
Crucial 512 SSD EK Supremacy EVO White Bitspower 150ml Reservoir POM White x 2 Swiftech 18w DDC x 2 
CoolingCoolingCoolingCooling
Bitspower 980ti HOF Waterblock (Clear)  EK SE 240mm Slim Radiator EK XE 240mm Radiator x 2 EK DDC Plexi top x 2  
OSKeyboardPowerCase
Windows 7 Professional NEX Moba White Pro EVGA 650 G2 Caselabs S3 
  hide details  
Reply
     
CPUMotherboardGraphicsGraphics
I7 5930K @ 4.5Ghz Asus Rampage V  GTX 980  GTX 980 
RAMRAMHard DriveHard Drive
Corsair Dominator Platinum 2666mhz DDR4 4 Gb Q... Dominator Light Bar Kits x 2 Crucial 240 SSD  Seagate 7200 Rpm Baracuda 
Hard DriveHard DriveHard DriveCooling
Seagate 7200 Rpm Baracuda Crucial M500 512 SSD Crucial M500 480 SSD EK 480mm Coolstream XTX x 2 
CoolingCoolingCoolingCooling
Tons of Fittings Supremacy Evo Copper EK  XSPC 240mm Radiator V3 x 2 Swiftech MCP35X PMW Pump DDC x 2 
CoolingCoolingCoolingCooling
EK Rampage V Mosfet WaterBlock Original CSQ NB Eloops B12 - 2 1300rpm  Phobia 8way 4pin Fan Controller x 2 Ek Single Link CSQ Bridge x 2 
CoolingCoolingCoolingCooling
Bitspower Z Tank (Clear) 250mm x 2 980 WaterBlocks x 2 Ek DDC Pump Top (Acrylic) x 2 Primochill 3/8" x 1/2" OD Clear Tubing 
CoolingCoolingOSMonitor
Bitspower 12mm Acyrlic Tubing 19" x 4  XSPC 3/8" x 1/2" Compression Fittings x 12 Windows 7 Professional 64 Bit Crossover 324K 
MonitorPowerCaseOther
Qnix 2710 Perfect Pixel 1440p  EVGA 1300 G2 CaseLabs SMA8 Darkside 12" Led Lighting  
CPUMotherboardGraphicsRAM
i7 7700k Asus Strix Z270i Gaming GALAX 980TI HOF Corsair Dominator Platinum DDR4 2400  
Hard DriveCoolingCoolingCooling
Crucial 512 SSD EK Supremacy EVO White Bitspower 150ml Reservoir POM White x 2 Swiftech 18w DDC x 2 
CoolingCoolingCoolingCooling
Bitspower 980ti HOF Waterblock (Clear)  EK SE 240mm Slim Radiator EK XE 240mm Radiator x 2 EK DDC Plexi top x 2  
OSKeyboardPowerCase
Windows 7 Professional NEX Moba White Pro EVGA 650 G2 Caselabs S3 
  hide details  
Reply
post #14133 of 22275
Quote:
Originally Posted by TheCautiousOne View Post

But don't you have copper now?

TCO

Oops I meant 1/2" soft copper. I was using hard copper but I could bend it well. I really didn't want to have to order metric tubing when I can go to home cheapo and buy rolls right off the shelf.
post #14134 of 22275
Quote:
Originally Posted by Chiobe View Post

Know this is stupid, but it would be nice to get answers, as it takes a while to get the cables.


Easily, unless you plan on doing a crazy routing job, it will most likely be a little tight for the lower or upper cages depending on which spot you mount your psu in, but it should still be able to reach.
Edited by 1Quickchic - 7/8/15 at 1:30pm
post #14135 of 22275
Quote:
Originally Posted by kgtuning View Post

Oops I meant 1/2" soft copper. I was using hard copper but I could bend it well. I really didn't want to have to order metric tubing when I can go to home cheapo and buy rolls right off the shelf.

I went with 8mm ID, 10mm OD half-hard from CopperTubingSales.com. Still more expensive perhaps than home Depot but half the price at McMasterCarr.

But holy wow is it hard biggrin.gif my bender is just a cheap 12" 10mm mini bender off eBay but it takes my whole weight with the bender on the floor to get it turning. Nice bends though!

This'll be going in my Daedalic S8+pedestal build, assuming the case does ever arrive wink.gif
Daedalic
(26 items)
 
Pegasus Server
(13 items)
 
My Girl's Box
(16 items)
 
  hide details  
Reply
Daedalic
(26 items)
 
Pegasus Server
(13 items)
 
My Girl's Box
(16 items)
 
  hide details  
Reply
post #14136 of 22275
Quote:
Originally Posted by Archea47 View Post

I went with 8mm ID, 10mm OD half-hard from CopperTubingSales.com. Still more expensive perhaps than home Depot but half the price at McMasterCarr.

But holy wow is it hard biggrin.gif my bender is just a cheap 12" 10mm mini bender off eBay but it takes my whole weight with the bender on the floor to get it turning. Nice bends though!

This'll be going in my Daedalic S8+pedestal build, assuming the case does ever arrive wink.gif

Honestly I want 1/2" stainless but... the cost is too much for me. I've had zero motivation to finish this thing. One day... lol
post #14137 of 22275
Quote:
Originally Posted by 1Quickchic View Post

Easily, unless you plan on doing a crazy routing job, it will most likely be a little tight for the lower or upper cages depending on which spot you mount your psu in, but it should still be able to reach.

I think he wants to mount cages to the th10's psu side and run the sata data cables from the mb to the hdd/ssds. If he plans to run rads on the bottom and top of the psu chamber that would leave the cage mount to the two middle fans of the psu chamber. Its still ideal to mount them here as that's where you typically see the sata ports on the board (the plane).


psu sata power, they're usually pretty long but it all comes down to the psu it self. You can always custom make your own sata power harness to make it look clean. I've seen this done a few times w/ caged hdd's.
post #14138 of 22275
Quote:
Originally Posted by wermad View Post

I'll get you some #s when i get home later today but I'm sure some might have the answer as well.
Thanks. It seems it will be safest to go with the 70cm cable length option.
So that leaves me with just the spacing between connectors (using HDD Cage Assy), so its less like this:

and more like this:
post #14139 of 22275
Quote:
Originally Posted by Chiobe View Post

Thanks. It seems it will be safest to go with the 70cm cable length option.
So that leaves me with just the spacing between connectors (using HDD Cage Assy), so its less like this:

and more like this:

Ah, ok, you're referring to power, ????
post #14140 of 22275
Quote:
Originally Posted by wermad View Post

Ah, ok, you're referring to power, ????
I thought I said that. Yes power.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Computer Cases
Overclock.net › Forums › Case Mods & Cases › Computer Cases › [Official] Case Labs Owners Club