Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
New Posts  All Forums:Forum Nav:

[Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET - Page 244

post #2431 of 10697
Quote:
Originally Posted by munaim1;14537860 
they are all on deafult I pressume?

What I want you to try is, decrease the PLL voltage to around 1.7/1.71v and test for stability and record what happens, then I want you to increase the PLL voltage to around 1.89v and again see what happens. The objective is to see whether or not your chip like high PLL or low PLL voltage, then we'll take it from there.

Could the problem be that I have spread spectrum enabled? I disabled it and am testing now. I'm positive I did not mess with those voltages when I was stable before, but I can try after this test.
post #2432 of 10697
Quote:
Originally Posted by fuloran1 View Post
Could the problem be that I have spread spectrum enabled? I disabled it and am testing now. I'm positive I did not mess with those voltages when I was stable before, but I can try after this test.
You know it could be.. I leave it off since on our board it slows blclk down and that's probably not healthy.
x99 Liquidx
(17 items)
 
Sandy z77 Pro
(11 items)
 
 
CPUMotherboardGraphicsRAM
Intel i7-6800k| 4.2Ghz | 1.291v ASRock x99 Professional Fatal1ty / 3.1 EVGA Titan X | EK-FC Copper | EK Backplate 32Gb Corsair Vengeance RGB DDR4 3467Mhz 
Hard DriveHard DriveHard DriveHard Drive
Samsung 850 PRO 512GB Samsung 850 EVO 500GB WD Red 3TB 2.5in HGST 500GB 
CoolingCoolingCoolingCooling
XSPC Rasa Dual Bay Reservoir | D5 XSPC RX360 Radiator EK Supremacy EVO | Red XSPC Photon 270 Reservoir 
CoolingOSMonitorPower
Alphacool UT60 280MM Radiator Windows 10 Pro x64 2 x Dell U2515H @ 75Hz Seasonic 1250XM 
Case
Corsair Graphite 780T 
CPUMotherboardGraphicsRAM
Intel Core i7 2700k | 48x | 1.328v Asrock Fatal1ty z77 Professional Asus DCUII GTX 670 | 2GB | 1254Mhz | 3.48Ghz  8GB Mushkin BL DDR3 | 2133Mhz | 1.5v 
Hard DriveHard DriveCoolingOS
Samsung 830 128GB  3x Seagate NL35 400GB 7200rpm XSPC Rasa Raystorm Extreme RX360 D5 Windows 10 Pro 
MonitorPowerCase
LG 23" 1080p IPS Corsair AX750 80+ Gold NZXT Source 210 Elite 
  hide details  
Reply
x99 Liquidx
(17 items)
 
Sandy z77 Pro
(11 items)
 
 
CPUMotherboardGraphicsRAM
Intel i7-6800k| 4.2Ghz | 1.291v ASRock x99 Professional Fatal1ty / 3.1 EVGA Titan X | EK-FC Copper | EK Backplate 32Gb Corsair Vengeance RGB DDR4 3467Mhz 
Hard DriveHard DriveHard DriveHard Drive
Samsung 850 PRO 512GB Samsung 850 EVO 500GB WD Red 3TB 2.5in HGST 500GB 
CoolingCoolingCoolingCooling
XSPC Rasa Dual Bay Reservoir | D5 XSPC RX360 Radiator EK Supremacy EVO | Red XSPC Photon 270 Reservoir 
CoolingOSMonitorPower
Alphacool UT60 280MM Radiator Windows 10 Pro x64 2 x Dell U2515H @ 75Hz Seasonic 1250XM 
Case
Corsair Graphite 780T 
CPUMotherboardGraphicsRAM
Intel Core i7 2700k | 48x | 1.328v Asrock Fatal1ty z77 Professional Asus DCUII GTX 670 | 2GB | 1254Mhz | 3.48Ghz  8GB Mushkin BL DDR3 | 2133Mhz | 1.5v 
Hard DriveHard DriveCoolingOS
Samsung 830 128GB  3x Seagate NL35 400GB 7200rpm XSPC Rasa Raystorm Extreme RX360 D5 Windows 10 Pro 
MonitorPowerCase
LG 23" 1080p IPS Corsair AX750 80+ Gold NZXT Source 210 Elite 
  hide details  
Reply
post #2433 of 10697
Quote:
Originally Posted by CloudX View Post
You know it could be.. I leave it off since on our board it slows blclk down and that's probably not healthy.
Exactly, I just noticed that my speed is an even 4500 where it was like 4489 or something before. My bus speed used to be 98...
post #2434 of 10697
Thread Starter 
Quote:
Originally Posted by fuloran1 View Post
Exactly, I just noticed that my speed is an even 4500 where it was like 4489 or something before. My bus speed used to be 98...
damn it forgot about spread spectrum, yeah it should be disabled for you, Asus afaik like's spread spectrum but it seems like the other's don't. Disable Spread spectrum and retest and also try what I recommended before.

Don't worry bud, we'll get you prime stable again
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #2435 of 10697
Quote:
Originally Posted by munaim1 View Post
damn it forgot about spread spectrum, yeah it should be disabled for you, Asus afaik like's spread spectrum but it seems like the other's don't. Disable Spread spectrum and retest and also try what I recommended before.

Don't worry bud, we'll get you prime stable again
Thanks man, and disabling ss didnt help, ran the 1792 fft and bsod'd after about 8 minutes. I'm gonna try what you said now.

Here is what the test looks like, crossing fingers, but it always fails after 7-10 minutes (this is with the pll at 1.7)


Edited by fuloran1 - 8/10/11 at 6:33pm
post #2436 of 10697
Ok, so now I didnt get a bsod, but a worker failed at 8 minutes. Raised pll to 1.89 and testing.
Edited by fuloran1 - 8/10/11 at 6:44pm
post #2437 of 10697
Thread Starter 
Quote:
Originally Posted by fuloran1 View Post
Ok, so now I didnt get a bsod, but a worker failed at 8 minutes.
that's progress!!! atleast it didn't bsod, now what I want you to do is increase the PLL a notch to around 1.71v and try again.

Just a reminder, now that you have disabled spreadspectrum your BCLK is locked to 100, therefore giving you a higher overclock than what you submitted, im not saying just because of that extra 0.x mhz your vcore may not be enough but remember there is a thin line between stable and not stable, just as a one vcore bump could make all the difference.


Anways try the above and report back.
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #2438 of 10697
Thread Starter 
Spreadsheet Update

I have created a new sheet for BIOS templates, it could be a reference point to other's including oneself and a quick 'copy and paste' whenever required in other threads/posts etc.

Those that have posted their stable systems please spare a few minutes of your time to do this. One more thing, these are the ones im after:
  • Main BIOS page (The advanced settings main page)

  • Full AI tweaker Page including DRAM Timing control

  • CPU Configuration Page


Enjoy
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #2439 of 10697
Quote:
Originally Posted by munaim1 View Post
that's progress!!! atleast it didn't bsod, now what I want you to do is increase the PLL a notch to around 1.71v and try again.

Just a reminder, now that you have disabled spreadspectrum your BCLK is locked to 100, therefore giving you a higher overclock than what you submitted, im not saying just because of that extra 0.x mhz your vcore may not be enough but remember there is a thin line between stable and not stable, just as a one vcore bump could make all the difference.


Anways try the above and report back.
Ok, I cant change it by that small of an increment, next step up was 1.75 from 1.71, then its 1.79 after that. Testing with the 1792 fft (My nemesis!!)

Also, should c1e be on or off?

*edit* another worker failed. Same one. Do the worker correspond to specific cores? If so, I'm beginning to wonder abut that core...It always runs the coolest and that worker is usually significantly behind the others (will be on test 5 when the rest are on say 10) during extended testing.
Edited by fuloran1 - 8/10/11 at 7:02pm
post #2440 of 10697
Quote:
Originally Posted by munaim1 View Post
Spreadsheet Update

I have created a new sheet for BIOS templates, it could be a reference point to other's including oneself and a quick 'copy and paste' whenever required in other threads/posts etc.

Those that have posted their stable systems please spare a few minutes of your time to do this. One more thing, these are the ones im after:
  • Main BIOS page (The advanced settings main page)

  • Full AI tweaker Page including DRAM Timing control

  • CPU Configuration Page


Enjoy
Sounds great!
RyzenWorkStation
(14 items)
 
  
CPUMotherboardGraphicsRAM
Ryzen 7 1700X Asrock X370 Taichi eVGA GTX 1080 Ti 16GB G.SKILL Flare X 
Hard DriveCoolingOSCase
Evo 960 Noctua NH-D15 Windows 10 Define R5 
Mouse
SteelSeries Xai Laser 
  hide details  
Reply
RyzenWorkStation
(14 items)
 
  
CPUMotherboardGraphicsRAM
Ryzen 7 1700X Asrock X370 Taichi eVGA GTX 1080 Ti 16GB G.SKILL Flare X 
Hard DriveCoolingOSCase
Evo 960 Noctua NH-D15 Windows 10 Define R5 
Mouse
SteelSeries Xai Laser 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
  • [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET