Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
New Posts  All Forums:Forum Nav:

[Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET - Page 582

post #5811 of 10702
Here are the results for manual voltage and LLC at ultra high and high:
High:
500
Ultra high:
500

To me it seems like setting it to high works a lot better, a bit more vdroop but the voltage is much more constant. Next thing to do is to keep it at high and start finding the right offset, correct?

Edit:

Quote:
Originally Posted by stevman17 View Post

338
Count me in. My first time OC'ing, and it was a blast.

Oh now you make my chip look bad, darn it! biggrin.gif

Great OC mate thumb.gif
Edited by Tuxi - 12/3/11 at 10:55am
post #5812 of 10702
Thread Starter 
Quote:
Originally Posted by Tuxi View Post

Here are the results for manual voltage and LLC at ultra high and high:
High:
500
Ultra high:
500

To me it seems like setting it to high works a lot better, a bit more vdroop but the voltage is much more constant. Next thing to do is to keep it at high and start finding the right offset, correct?

Ultra high does indeed seem the best one to reduce vdroop, however, high LLC will enable you to to have a higher idle voltage, but that might not be necessary unless you start experiencing idle bsods.

For now I would recommend that you leave it on Ultra high, and set the vcore to offset. please use cpu-z instead, post a screenshot of idle voltage and load voltage.

More importantly disable C3 and C6 report, enable C1E and Speedstep. That alone should tackle the idle bsods if you get them. If you do get idle bsods later on, then the next thing would be to reduce the LLC to high and increase the offset amount to allow for a more higher idle voltage but as I mentioned it's not necessary right now. smile.gif
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #5813 of 10702
i feel your club is discrimitory I can't OC an i3 but its still sandybridge frown.gif
post #5814 of 10702
Thread Starter 
Quote:
Originally Posted by TheSandman View Post

i feel your club is discrimitory I can't OC an i3 but its still sandybridge frown.gif

Overclock that baby to 4ghz+ and I'll add a section for all other SB smile.gif

That sound good? tongue.gif
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #5815 of 10702
Quote:
Originally Posted by munaim1 View Post

Ultra high does indeed seem the best one to reduce vdroop, however, high LLC will enable you to to have a higher idle voltage, but that might not be necessary unless you start experiencing idle bsods.
For now I would recommend that you leave it on Ultra high, and set the vcore to offset. please use cpu-z instead, post a screenshot of idle voltage and load voltage.
More importantly disable C3 and C6 report, enable C1E and Speedstep. That alone should tackle the idle bsods if you get them. If you do get idle bsods later on, then the next thing would be to reduce the LLC to high and increase the offset amount to allow for a more higher idle voltage but as I mentioned it's not necessary right now. smile.gif

Here's a pic with LLC at ultra high and offset -0.70. Idle and load:289

Edit: And I actually did drop the C3 C6 off and left C1E and speedstep on today, haven't gotten any BSODs yet.

I was only using the HWMonitor so you guys could see the vCore fluctuation.
post #5816 of 10702
Thread Starter 
Quote:
Originally Posted by Tuxi View Post

Quote:
Originally Posted by munaim1 View Post

Ultra high does indeed seem the best one to reduce vdroop, however, high LLC will enable you to to have a higher idle voltage, but that might not be necessary unless you start experiencing idle bsods.
For now I would recommend that you leave it on Ultra high, and set the vcore to offset. please use cpu-z instead, post a screenshot of idle voltage and load voltage.
More importantly disable C3 and C6 report, enable C1E and Speedstep. That alone should tackle the idle bsods if you get them. If you do get idle bsods later on, then the next thing would be to reduce the LLC to high and increase the offset amount to allow for a more higher idle voltage but as I mentioned it's not necessary right now. smile.gif

Here's a pic with LLC at ultra high and offset -0.70. Idle and load:289

Edit: And I actually did drop the C3 C6 off and left C1E and speedstep on today, haven't gotten any BSODs yet.

I was only using the HWMonitor so you guys could see the vCore fluctuation.

thinking.gif that is quite low lol, do the same for High LLC and obviously increase the offset value and post screenshot again. smile.gif
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #5817 of 10702
Quote:
Originally Posted by munaim1 View Post

thinking.gif that is quite low lol, do the same for High LLC and obviously increase the offset value and post screenshot again. smile.gif

After monitoring the CPU-Z for a while I realized my vCore jumps between 0.89-1.05V all the time. It doesn't just settle down. poke.gif

Edit: Nevermind, I think think the computer wasn't fully idle since now its between 0.88-0.90V, no bumps to 1.0V
post #5818 of 10702
Thread Starter 
Quote:
Originally Posted by Tuxi View Post

Quote:
Originally Posted by munaim1 View Post

thinking.gif that is quite low lol, do the same for High LLC and obviously increase the offset value and post screenshot again. smile.gif

After monitoring the CPU-Z for a while I realized my vCore jumps between 0.89-1.05V all the time. It doesn't just settle down. poke.gif

Edit: Nevermind, I think think the computer wasn't fully idle since now its between 0.88-0.90V, no bumps to 1.0V

Yeah that's normal, have you done the same for LLC high?
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
post #5819 of 10702
Quote:
Originally Posted by munaim1 View Post

Yeah that's normal, have you done the same for LLC high?

There you go. I think I'll leave Prime95 Blend running overnight to see how it works. Load vCore jumps between 1.248-1.264V and idle between 0.920-0.936V.
289
post #5820 of 10702
Thread Starter 
Quote:
Originally Posted by Tuxi View Post

Quote:
Originally Posted by munaim1 View Post

Yeah that's normal, have you done the same for LLC high?

There you go. I think I'll leave Prime95 Blend running overnight to see how it works. Load vCore jumps between 1.248-1.264V and idle between 0.920-0.936V.
289

Looks better, atleast it doesn't drop below 0.900 like Ultra high does. Hopefully that works for you, remember when using Offset disable C3 and C6 and enable both C1E and Speedstep.

Good luck and hopefully it passes a 12hour blend smile.gif
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
it looks alive
(17 items)
 
Sandy Transformed
(69 photos)
 
CPUMotherboardGraphicsRAM
i5 2500K [5ghz 1.44v 24/7] Asus Maximus IV Extreme SLI GTX 460 @ 920/1840/4100 [1.11v] 4GB Dominator GT @ 2133mhz CL8 [1.65v] 
Hard DriveHard DriveCoolingOS
Intel X25-M G2 80GB 3x Samsung F3 500GB RAID 0 EK Supreme HF Full Copper Windows 7 Ultimate 64bit 
MonitorPowerCaseAudio
LG42SL9500 42" 1080p [Surround Soon] XFX XXX Edition 650w Xigmatec Elysium JVC HA-RX700 [foam mod] 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
  • [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET