Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
New Posts  All Forums:Forum Nav:

[Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET - Page 703

post #7021 of 10699
Quote:
Originally Posted by kevindd992002 View Post

I just need to confirm, what are your voltages now while stress testing? VCCIO, VDIMM, and PLL. Sorry, I don't seem to understand some parts of your answer above.
Well, mine passed Memtest for around 24 hours at 1.5V. Does that mean I do not have to worry?

You might be able to do rated timings if you go ahead and increase the voltage. relaxing the timings working suggests something was stressed too much. my settings are as follows(from memory, might be off a point or two, ill post a screen shot of my bios if successful)

ill be attempting to back off of some of the bus voltages soon as this stress testing finishes.



mult: 45
pll overvoltage: enabled

LLC = High
VRM Frequency is manually set at 350
Phase Control: Extreme
Cpu Overcurrent: 140%
vcore offset: +0.035v
Dram Voltage: 1.55
VCCSA = 0.925v
VCCIO = 1.2 (i took one step off as my mobo overvolts slightly, so 1.2 minus one)
CPU PLL Voltage: 1.7
cpu spread spectrum: Enabled

C1E/Speedstep Enabled, C3/C6 Disabled

Dont worry too much for your dimms, 1.55v is well within 5%, in fact you could do 1.575, most things in the electronics world are +-5% for rated values
Edited by ryuji - 1/30/12 at 7:36am
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
post #7022 of 10699
Quote:
Originally Posted by ryuji View Post

You might be able to do rated timings if you go ahead and increase the voltage. relaxing the timings working suggests something was stressed too much. my settings are as follows(from memory, might be off a point or two, ill post a screen shot of my bios if successful)
ill be attempting to back off of some of the bus voltages soon as this stress testing finishes.
mult: 45
pll overvoltage: enabled
LLC = High
VRM Frequency is manually set at 350
Phase Control: Extreme
Cpu Overcurrent: 140%
vcore offset: +0.035v
Dram Voltage: 1.55
VCCSA = 0.925v
VCCIO = 1.2 (i took one step off as my mobo overvolts slightly, so 1.2 minus one)
CPU PLL Voltage: 1.7
cpu spread spectrum: Enabled
C1E/Speedstep Enabled, C3/C6 Disabled
Dont worry too much for your dimms, 1.55v is well within 5%, in fact you could do 1.575, most things in the electronics world are +-5% for rated values

Well, at 1.2 VCCIO and 1.65 VDIMM my modules still cannot run at CAS6 rated latency 1600MHz. I think CAS6 is really very low of a latency for 1600MHz 8GB (4x2GB) anyway. It is expected for the system to not boot with those settings even though you increase all voltages relating to the IMC. Well, my question is that will I have problems running them at 1.5V 1600MHz?

People keep saying to run your RAM modules at stock initially when overclocking your CPU. I agree to this if you are using 2-RAM module kits alone. It will be different with 4-RAM modules (2 kits) because timings should be more relaxed. I think this information should be included in the OP of this thread as a NOTE to users following the guide. Just a suggestion.
Edited by kevindd992002 - 1/30/12 at 7:50am
post #7023 of 10699
Quote:
Originally Posted by kevindd992002 View Post

Well, at 1.2 VCCIO and 1.65 VDIMM my modules still cannot run at CAS6 rated latency 1600MHz. I think CAS6 is really very low of a latency for 1600MHz 8GB (4x2GB) anyway. It is expected for the system to not boot with those settings even though you increase all voltages relating to the IMC. Well, my question is that will I have problems running them at 1.5V 1600MHz?
People keep saying to run your RAM modules at stock initially when overclocking your CPU. I agree to this if you are using 2-RAM module kits alone. It will be different with 4-RAM modules (2 kits) because timings should be more relaxed. I think this information should be included in the OP of this thread as a NOTE to users following the guide. Just a suggestion.

I am using c7(1600) corsair vengeance. Works xmp or manual style. I bumped it a notch just to be safe. I did not see any cas6 that was reasonably priced. Have you tried using the xmp?
    
CPUMotherboardGraphicsRAM
i5-2500k Asus Maximus gene-z/gen3 Gigabyte 6950 HD OC Corsair Vengeance 16 gig 8x2 CL7 
Hard DriveCoolingOSMonitor
Adata 120gig Sata 3 AS510s3 Noctua 2011 SE NP-D14  Microsoft Windows 7 (Home Premium) 64bit 55 inch Samsung 3d Tv 
MonitorPowerCaseMouse
27 inch Gateway  OCZ ZT Series 750W Fully-Modular 80PLUS Bronze  Rosewill Thor V2 Logitech Performance Gaming Mouse (wireless) 
Mouse PadAudio
rocketfish Onkyo tx-nr1008 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
i5-2500k Asus Maximus gene-z/gen3 Gigabyte 6950 HD OC Corsair Vengeance 16 gig 8x2 CL7 
Hard DriveCoolingOSMonitor
Adata 120gig Sata 3 AS510s3 Noctua 2011 SE NP-D14  Microsoft Windows 7 (Home Premium) 64bit 55 inch Samsung 3d Tv 
MonitorPowerCaseMouse
27 inch Gateway  OCZ ZT Series 750W Fully-Modular 80PLUS Bronze  Rosewill Thor V2 Logitech Performance Gaming Mouse (wireless) 
Mouse PadAudio
rocketfish Onkyo tx-nr1008 
  hide details  
Reply
post #7024 of 10699
Quote:
Originally Posted by kevindd992002 View Post

Well, at 1.2 VCCIO and 1.65 VDIMM my modules still cannot run at CAS6 rated latency 1600MHz. I think CAS6 is really very low of a latency for 1600MHz 8GB (4x2GB) anyway. It is expected for the system to not boot with those settings even though you increase all voltages relating to the IMC. Well, my question is that will I have problems running them at 1.5V 1600MHz?
People keep saying to run your RAM modules at stock initially when overclocking your CPU. I agree to this if you are using 2-RAM module kits alone. It will be different with 4-RAM modules (2 kits) because timings should be more relaxed. I think this information should be included in the OP of this thread as a NOTE to users following the guide. Just a suggestion.

You have nothing to worry about. The folks that say to run ram at stock are only saying you shouldnt overclock your dimms while trying to overclock your cpu. That way you can scientifically deduce exactly where your problem is. In fact some people advocate running ram at 1333 on SB as that is the reference speed for the chip

Once you find your stable cpu overclock it is expected that you go nuts and see what you can get on your ram, however



Well, i found a stable operating point. Here is my submission: time to start fine tuning my pll/vccio voltages

169


heres some interesting behavior i noticed reviewing my temperature chart: my memory sensor seems to drift over the course of 20 minutes from 50C to 60C but its finally stable with all four dimms installed wheee.gif
457
Temps are a bit warm, but my computer runs dead silent =)

Trying bringing VCCIO all the way back down to 1.1v. i got a feeling the memory voltage is what did it, not the IO



Nobody has any insight on this? trying to decide if its worth giving my 2600k another shot before i throw it in the trash (Click to show)
Quote:
Originally Posted by ryuji View Post

... my 2600k seemed to scale better with voltage.
and on that note, if anyone has experience with this and how to resolve the issue:
my debugging/part swapping lead me to think the IMC died or was faulty even tho all my bus voltages were at intel nominal values and the cpu voltage at 1.35v manual ultra high LLC 4.6 ghz but i believe was good at high LLC
behavior i had was this: the system was fine stable as a rock for 4 or so months, then in the middle of my nephew playing fallout 3 i got a BSOD who's code was related to memory, i ignored it as just a fluke but within a few hours i got many more BSOD's which lead to massive filesystem corruption and 'Memory Managment' related BSOD's about half the time. i tried going 100% stock to no results, eventually the cpu wouldnt post at my 1600 mhz memory oc and had to run at 1333. memtest would work fine for all tests that fit inside cpu cache, and on the fade test, it would mess up hard enough to fully scramble the screen/freeze memtest
I recall stepping each bus voltage up a few steps, and memory voltage a few steps individually and collectively. gave up and bought my 2500k and ssd instead of a new 2600k(glad i spent the cash on ssd instead of 2mb cache)
i think back when i fooled around with it i was able to bench etc at 1.425v 4.8 ghz on that cpu with HT turned on

Edited by ryuji - 1/30/12 at 11:32am
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
post #7025 of 10699
Quote:
Originally Posted by ryuji View Post

Quote:
Originally Posted by kevindd992002 View Post

Well, at 1.2 VCCIO and 1.65 VDIMM my modules still cannot run at CAS6 rated latency 1600MHz. I think CAS6 is really very low of a latency for 1600MHz 8GB (4x2GB) anyway. It is expected for the system to not boot with those settings even though you increase all voltages relating to the IMC. Well, my question is that will I have problems running them at 1.5V 1600MHz?
People keep saying to run your RAM modules at stock initially when overclocking your CPU. I agree to this if you are using 2-RAM module kits alone. It will be different with 4-RAM modules (2 kits) because timings should be more relaxed. I think this information should be included in the OP of this thread as a NOTE to users following the guide. Just a suggestion.

You have nothing to worry about. The folks that say to run ram at stock are only saying you shouldnt overclock your dimms while trying to overclock your cpu. That way you can scientifically deduce exactly where your problem is. In fact some people advocate running ram at 1333 on SB as that is the reference speed for the chip

Once you find your stable cpu overclock it is expected that you go nuts and see what you can get on your ram, however



Well, i found a stable operating point. Here is my submission: time to start fine tuning my pll/vccio voltages

I hid your picture in a spoiler to save space. -shad0wfax (Click to show)

169

 



heres some interesting behavior i noticed reviewing my temperature chart: my memory sensor seems to drift over the course of 20 minutes from 50C to 60C but its finally stable with all four dimms installed wheee.gif
I hid your picture in a spoiler to save space -shad0wfax (Click to show)

457

 


Temps are a bit warm, but my computer runs dead silent =)

Trying bringing VCCIO all the way back down to 1.1v. i got a feeling the memory voltage is what did it, not the IO



Nobody has any insight on this? trying to decide if its worth giving my 2600k another shot before i throw it in the trash (Click to show)
Quote:
Originally Posted by ryuji View Post

... my 2600k seemed to scale better with voltage.
and on that note, if anyone has experience with this and how to resolve the issue:
my debugging/part swapping lead me to think the IMC died or was faulty even tho all my bus voltages were at intel nominal values and the cpu voltage at 1.35v manual ultra high LLC 4.6 ghz but i believe was good at high LLC
behavior i had was this: the system was fine stable as a rock for 4 or so months, then in the middle of my nephew playing fallout 3 i got a BSOD who's code was related to memory, i ignored it as just a fluke but within a few hours i got many more BSOD's which lead to massive filesystem corruption and 'Memory Managment' related BSOD's about half the time. i tried going 100% stock to no results, eventually the cpu wouldnt post at my 1600 mhz memory oc and had to run at 1333. memtest would work fine for all tests that fit inside cpu cache, and on the fade test, it would mess up hard enough to fully scramble the screen/freeze memtest
I recall stepping each bus voltage up a few steps, and memory voltage a few steps individually and collectively. gave up and bought my 2500k and ssd instead of a new 2600k(glad i spent the cash on ssd instead of 2mb cache)
i think back when i fooled around with it i was able to bench etc at 1.425v 4.8 ghz on that cpu with HT turned on


I agree about the RAM. The reason people say not to mess with RAM settings is as stated above: It's easier to change one variable at a time, get stable, and then work on the second variable than it is to change two variables at once and try to stabilize both. If you try to OC your RAM and CPU simultaneously on a new system you could be chasing your tail for weeks before you get lucky and stumble onto a stable OC that you like for both. :)

 

As for your temperatures, I think that there's nothing wrong with them at all, especially if you're on air and running a quiet system.

B2
(8 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core i7-5930K Haswell-E 6-Core 3.5GHz LGA... EVGA X99 Classified (151-HE-E999-KR) LGA 2011-v... EVGA 04G-P4-3975-KR GeForce GTX 970 SSC ACX 2.0... EVGA 04G-P4-3975-KR GeForce GTX 970 SSC ACX 2.0... 
RAMHard DriveCoolingCase
G.SKILL Ripjaws 4 series 16GB (4 x 4GB) 288-Pin... SAMSUNG 850 EVO MZ-75E1T0B/AM 2.5" 1TB SATA III... CORSAIR Hydro Series H100i Extreme Performance ... Phanteks Enthoo Luxe Series PH-ES614L_BK Black ... 
  hide details  
Reply
B2
(8 items)
 
  
CPUMotherboardGraphicsGraphics
Intel Core i7-5930K Haswell-E 6-Core 3.5GHz LGA... EVGA X99 Classified (151-HE-E999-KR) LGA 2011-v... EVGA 04G-P4-3975-KR GeForce GTX 970 SSC ACX 2.0... EVGA 04G-P4-3975-KR GeForce GTX 970 SSC ACX 2.0... 
RAMHard DriveCoolingCase
G.SKILL Ripjaws 4 series 16GB (4 x 4GB) 288-Pin... SAMSUNG 850 EVO MZ-75E1T0B/AM 2.5" 1TB SATA III... CORSAIR Hydro Series H100i Extreme Performance ... Phanteks Enthoo Luxe Series PH-ES614L_BK Black ... 
  hide details  
Reply
post #7026 of 10699

This is happening to my 2500K now, I think it's dying =/
post #7027 of 10699
Quote:
Originally Posted by shad0wfax View Post

As for your temperatures, I think that there's nothing wrong with them at all, especially if you're on air and running a quiet system.
Actually, im running dual independent water cooling loops but im running low speed Yate Loon 120mm fans at 7v so my temperatures are a little bit more like air cooling, instead of water cooling. But you cant hear it running at 4.5 ghz and with one of the hotter graphics cards around wink.gif
Quote:
Originally Posted by piskooooo View Post

This is happening to my 2500K now, I think it's dying =/

Tell me if you come up with any solutions. As much as i dont wish this upon someone else, The saying of 'misery loves company' comes to mind sad-smiley-002.gif
Edited by ryuji - 1/30/12 at 1:01pm
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
post #7028 of 10699
Hey guys. I was turned onto this club today:) Last night I ran prime95 on custom blend(7 out of 8 gigs used)@4.7Ghz. Cooler is a Silver Arrow with 2 SanAce 1011's and ICD7 paste:) I have 3 pics of the run..the only problem is I did this before reading about the club entry rules. If I need to I can rerun the test's with RealTemp. I used HWMonitor frown.gif let me know If I need to rerun the test. here are pics.

337

337



And for giggles.

371

Thanks.
Gizmoto
(18 items)
 
They beat me:(
(15 items)
 
Home Server V1.0
(17 items)
 
CPUMotherboardGraphicsRAM
AMD Phenom II x6 1040t @2.7Ghz ASRock 880GM-LE FX  AMD Radeon HD 4250 integrated graphics Micro Center(ADATA) 8Gb (2x4) 1333 
Hard DriveHard DriveHard DriveHard Drive
Western Digital Caviar Blue 640Gb Samsung SpinPoint F4 2Tb Seagate Barracuda 7200.9 ST3500641AS-RK 500Gb Seagate Barracuda 7200.9 ST3500641AS-RK 500Gb 
Optical DriveOptical DriveCoolingOS
ASUS 24X DVD Burner ASUS 24X DVD Burner Stock AMD Cooler Windows 7 Home Premium 64 bit 
OSOSPowerCase
Linux Mint (VM) Linux Ubuntu (VM) Inland ILG-500R2 500w PSU DiabloTek Evo Mid-tower Case 
Other
Inland IL internal card reader 
  hide details  
Reply
Gizmoto
(18 items)
 
They beat me:(
(15 items)
 
Home Server V1.0
(17 items)
 
CPUMotherboardGraphicsRAM
AMD Phenom II x6 1040t @2.7Ghz ASRock 880GM-LE FX  AMD Radeon HD 4250 integrated graphics Micro Center(ADATA) 8Gb (2x4) 1333 
Hard DriveHard DriveHard DriveHard Drive
Western Digital Caviar Blue 640Gb Samsung SpinPoint F4 2Tb Seagate Barracuda 7200.9 ST3500641AS-RK 500Gb Seagate Barracuda 7200.9 ST3500641AS-RK 500Gb 
Optical DriveOptical DriveCoolingOS
ASUS 24X DVD Burner ASUS 24X DVD Burner Stock AMD Cooler Windows 7 Home Premium 64 bit 
OSOSPowerCase
Linux Mint (VM) Linux Ubuntu (VM) Inland ILG-500R2 500w PSU DiabloTek Evo Mid-tower Case 
Other
Inland IL internal card reader 
  hide details  
Reply
post #7029 of 10699
Comparing the time between "Starting Workers" in prime95's main thread with the time at which "Test 20" completed suggests it's been running for 12hrs, you might get away with it lol wink.gif
post #7030 of 10699
So i dropped my pll voltage as low as it would post at and i got down to 1.4v. stress testing at 1.4v pll and 1.08v VCCIO... seems like my cpu likes low voltages A LOT.

Is it worth undervolting VCCSA too?

should probably after done with all the i/o voltages take another look at dram/VCORE, maybe they will go lower


just a point of interest:
lowering my i/o voltages seem to be lessening the demand on the cpu regulators as my regulators are running nearly 5 degs cooler then before
Edited by ryuji - 1/30/12 at 7:38pm
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
Desktop
(12 items)
 
Router/Server
(6 items)
 
 
CPUMotherboardGraphicsRAM
2600k@4.7 Ghz Asus Sabertooth P67 Sapphire HD5870 4x4gb Corsair Vengeance 
Hard DriveOptical DriveCoolingMonitor
120 GB OCZ Vertex 3 Bluray RW drive Silent dual loop water cooling gpu+cpu 2x ASUS VE247H (23.6 inch LED) 
PowerCaseMouseAudio
Antec Truepower Quattro 1KW Thermaltake Armor Razer Naga Epic Asus Xonar D2X, 5.1 channel tube amp 
CPUMotherboardRAMHard Drive
E8400 Rampage Formula Mushkin DDR2 3x WD Caviar Black 1TB 64mb cache 
CoolingOS
Silent water cooling 1x120mm radiator, chipset+... Gentoo Linux 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Intel CPUs
  • [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET
Overclock.net › Forums › Intel › Intel CPUs › [Official] The Sandy Stable Club **Guides, Voltages, Temps & BIOS Templates** Inc SPREADSHEET