Overclock.net › Forums › Cooling › Water Cooling › [Official] Antec Kühler H2O 620 & 920 Owners Club
New Posts  All Forums:Forum Nav:

[Official] Antec Kühler H2O 620 & 920 Owners Club - Page 366

Poll Results: Which Antec cooler do you own?

 
  • 54% (152)
    Antec Kühler H2O 620
  • 45% (129)
    Antec Kühler H2O 920
281 Total Votes  
post #3651 of 6063
Quote:
Originally Posted by Totally Dubbed View Post

3 pin WILL work, but the program won't be able to control it.
I suggest you stay on stock fans as they perform very well - however if you want a quieter PC (you be the judge of the noise levels) then think of changing fans thumb.gif

Hmm i don't OC my CPU , i think at it's " Silence " mode ( was it Silence mod ? ) i think i will do fine , i saw it at max mod blinksmiley.gif Mother of god...i thought our car radiator fan is noisy.....

I have 2 ideas , will either one work ?

1) What if i do this , i have one of my fan ( not Antect stock but my 3pin LED fan ) plug into my Mobo , have my Mobo control it instead , while the other stock Antec fan plug into the 4 pin PWM connector on the pump. The program still will work right ? But it only controls one fan , but i wonder will cooling efficiency still be any good if so thinking.gif

OR

2) I saw one of this an Arctic Cooling Arctic F PWM Fan 120mm , they are very cheap and their are PWM , they should work with the program then right ? But originally the fans can go up to 2200 RPM , but this are only 1350 RPM , can they work with the program ? And i think i can go full out with this fans , since 1350 RPM won't produce much noise , my 140mm Xigmatek fans are running at full 1100 rpm , 4 piece not to mention , are still quite quiet biggrin.gif I heard Arctic Cooling fans are pretty good too thumb.gif

http://www.arctic.ac/en/p/cooling/case-fans/73/arctic-f-pwm.html
Quote:
Originally Posted by plywood99 View Post

Version 4 changed a few things, mainly with the pump / block itself.
The block now uses a center inlet, dual side outlet. Older versions used a side to side inlet outlet.
Center inlet should be good for a couple degrees improvement.
Also the pump has been improved for better pressure and flow.
I'm very tempted to get a V4 and mod it, just to compare with my old one.

Here is a link to the official press release.

http://www.asetek.com/press-room/news/366-asetekr-releases-fourth-generation-of-patented-all-in-one-liquid-coolers.html

Yuppers the itch to upgrade is really getting... uhm... itchy tongue.gif

Lazy to scroll up and read everything through again lol , but are you guys talking about Antec 920 or Asetek ones ? ( I know Asetek make for Antec ) if it's Antec how you tell it's V4 ? But my country only recently brought in this Antec coolers , they never exist back in 2011
Edited by Gh0sT-NoVa - 2/17/13 at 6:57am
post #3652 of 6063
Thread Starter 
Quote:
Originally Posted by Gh0sT-NoVa View Post

Hmm i don't OC my CPU , i think at it's " Silence " mode ( was it Silence mod ? ) i think i will do fine , i saw it at max mod blinksmiley.gif Mother of god...i thought our car radiator fan is noisy.....

I have 2 ideas , will either one work ?
1

I suggest sticking to stock antec fans. They are great fans on idle/low load.
Get the Antec 920 in, then worry about fans rolleyes.gif
post #3653 of 6063
Quote:
Originally Posted by Totally Dubbed View Post

I suggest sticking to stock antec fans. They are great fans on idle/low load.
Get the Antec 920 in, then worry about fans rolleyes.gif

Yeah i guess your right , i been thinking i though , might just save my money and use the stock ones , since it's black too can't complain , it matches my full black build too thumb.gif

And i know where to install my Xigmatek fan instead , on my HDD cage since i originally had thought of installing fans there biggrin.gif
Quote:
Originally Posted by plywood99 View Post

Version 4 changed a few things, mainly with the pump / block itself.
The block now uses a center inlet, dual side outlet. Older versions used a side to side inlet outlet.
Center inlet should be good for a couple degrees improvement.
Also the pump has been improved for better pressure and flow.
I'm very tempted to get a V4 and mod it, just to compare with my old one.

Here is a link to the official press release.

http://www.asetek.com/press-room/news/366-asetekr-releases-fourth-generation-of-patented-all-in-one-liquid-coolers.html

About this , did he meant for Antec or Asetek only?
post #3654 of 6063
i just picked a antec25 kuhler 620 h2o used but it did not come with any of the brakets for a intel board i have the screws but no brakets. i was wounder if any one had some that they could part with. i cant find any on the net to buy. thx. i run a 775 mother board. thx all its all set now i have one coming. thx.
Edited by thedoc77 - 2/19/13 at 3:09pm
post #3655 of 6063
Update: As I had said I would, I put my 212+ back in to see what kind of temps I'd be getting with it. It is mounted with one Coolermaster Blademaster (R4) fan in push config. Idle temps were ~3-4c lower than with the 920 but temps hit 93 when I ran p95. To refresh your memory, my max temp with the 920 was 89c. Room temp was a bit warmer today, ~70F compared to the previous 65. No other variables have changed (like case airflow).

I'll report back once I get my new 920.
Edited by 8bitG33k - 2/17/13 at 10:06pm
post #3656 of 6063
Quote:
Originally Posted by thedoc77 View Post

i just picked a antec25 kuhler 620 h2o used but it did not come with any of the brakets for a intel board i have the screws but no brakets. i was wounder if any one had some that they could part with. i cant find any on the net to buy. thx. i run a 775 mother board.

The little metal thingies that go into the backplate? Antec is usually pretty good with sending replacements, I'd send an email/ open a support ticket. The two times I have dealt with Antec Customer Service I have been very impressed.
post #3657 of 6063
Upgrading my 620 to a 920, are the mounting systems interchangeable or will I have to disassemble and swap?
Mighty-iTX
(12 items)
 
One foot in..
(17 items)
 
mATX
(12 items)
 
CPUMotherboardGraphicsRAM
i7-4770K M7-Impact Strix GTX980 Samsung 
Hard DriveCoolingOSMonitor
Crucial M4 256 Glacer 240L W8.1 K272HUL 
KeyboardPowerCaseMouse
Saitek Seasonic X-650 Prodigy MX518 
CPUMotherboardGraphicsGraphics
4770K/45/43 Maximus VI Extreme R290X R290X 
RAMHard DriveHard DriveOptical Drive
Samsung Crucial M4 64GB RAIDR LSSWM 
CoolingOSMonitorKeyboard
Cooler Master Glacer 7 Ultimate 64 SyncMaster Eclipse 
PowerCaseMouseMouse Pad
XFX 1050 BE 600T Silver MX518 Desk 
CPUMotherboardGraphicsRAM
i5-4330 Z87 Gryphon GTX690 G.Skill RipJawsX 
Hard DriveCoolingOSMonitor
WD Blacks Hyper 212 W8.1 ACER 
KeyboardPowerCaseMouse
Logitech Ultra X3 1000w Corsair 230T Orange Razer 
  hide details  
Reply
Mighty-iTX
(12 items)
 
One foot in..
(17 items)
 
mATX
(12 items)
 
CPUMotherboardGraphicsRAM
i7-4770K M7-Impact Strix GTX980 Samsung 
Hard DriveCoolingOSMonitor
Crucial M4 256 Glacer 240L W8.1 K272HUL 
KeyboardPowerCaseMouse
Saitek Seasonic X-650 Prodigy MX518 
CPUMotherboardGraphicsGraphics
4770K/45/43 Maximus VI Extreme R290X R290X 
RAMHard DriveHard DriveOptical Drive
Samsung Crucial M4 64GB RAIDR LSSWM 
CoolingOSMonitorKeyboard
Cooler Master Glacer 7 Ultimate 64 SyncMaster Eclipse 
PowerCaseMouseMouse Pad
XFX 1050 BE 600T Silver MX518 Desk 
CPUMotherboardGraphicsRAM
i5-4330 Z87 Gryphon GTX690 G.Skill RipJawsX 
Hard DriveCoolingOSMonitor
WD Blacks Hyper 212 W8.1 ACER 
KeyboardPowerCaseMouse
Logitech Ultra X3 1000w Corsair 230T Orange Razer 
  hide details  
Reply
post #3658 of 6063
Thread Starter 
Quote:
Originally Posted by grunion View Post

Upgrading my 620 to a 920, are the mounting systems interchangeable or will I have to disassemble and swap?

The mounts are identical.
But I don't get what you're changing here? Or should I say I don't understand the question.
Quote:
Originally Posted by 8bitG33k View Post

Update: As I had said I would, I put my 212+ back in to see what kind of temps I'd be getting with it. It is mounted with one Coolermaster Blademaster (R4) fan in push config. Idle temps were ~3-4c lower than with the 920 but temps hit 93 when I ran p95. To refresh your memory, my max temp with the 920 was 89c. Room temp was a bit warmer today, ~70F compared to the previous 65. No other variables have changed (like case airflow).

Cheers for the update man!
post #3659 of 6063
Quote:
Originally Posted by thedoc77 View Post

i just picked a antec25 kuhler 620 h2o used but it did not come with any of the brakets for a intel board i have the screws but no brakets. i was wounder if any one had some that they could part with. i cant find any on the net to buy. thx. i run a 775 mother board.

I have the intel bracket handy, Where abouts are you bro ?
My Basic Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD FX-6100 Asus Sabertooth 990FX XFX Radeon HD 7770 GSkill Ripjawsx 
Optical DriveOptical DriveCoolingCooling
IHas iHas 140 MM Fan x3 Antec kuhler 620 
KeyboardPowerCaseMouse
Stock Packard Bell atm lol XFX 650W XXX Edition Semi-Modular Lian li K62 ThermalTake Azurues 
Mouse Pad
Currently none 
  hide details  
Reply
My Basic Rig
(13 items)
 
  
CPUMotherboardGraphicsRAM
AMD FX-6100 Asus Sabertooth 990FX XFX Radeon HD 7770 GSkill Ripjawsx 
Optical DriveOptical DriveCoolingCooling
IHas iHas 140 MM Fan x3 Antec kuhler 620 
KeyboardPowerCaseMouse
Stock Packard Bell atm lol XFX 650W XXX Edition Semi-Modular Lian li K62 ThermalTake Azurues 
Mouse Pad
Currently none 
  hide details  
Reply
post #3660 of 6063
Quote:
Originally Posted by Falmod View Post

I have the intel bracket handy, Where abouts are you bro ?

Is that what he means, the backplate? Or the inserts? Since he was using plural I asssumed he meant the screw inserts or possibly the Tension Clips. Since he also said Intel though, he may have meant the backplate.

backplate...




backplate metal inserts:



and then the ---> Tension clips <---
Edited by 8bitG33k - 2/18/13 at 2:35pm
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › [Official] Antec Kühler H2O 620 & 920 Owners Club