Overclock.net › Forums › Cooling › Water Cooling › [Official] Antec Kühler H2O 620 & 920 Owners Club
New Posts  All Forums:Forum Nav:

[Official] Antec Kühler H2O 620 & 920 Owners Club - Page 427

Poll Results: Which Antec cooler do you own?

 
  • 54% (153)
    Antec Kühler H2O 620
  • 45% (130)
    Antec Kühler H2O 920
283 Total Votes  
post #4261 of 6068
Thread Starter 
Warning: Spoiler! (Click to show)
Quote:
Originally Posted by M3TAl View Post

Here it is.
In other words as long as the lapping doesn't cause any damage then you still have warranty.

Quote:
Originally Posted by SinatraFan View Post

OK,,,

As I recall, when I first used it on my AMD board with a FX-8150 chip:

1) I removed the fan bracket that was installed on my MSI MOBO.

2) I put the 2 adhesive strips on the rectangular plastic back plate that came with H20

3) Installed the metal nuts into the back plate

4) Installed the back plate to the back side of the MOBO

5) when you assemble the pump fastener ring, make sure the plastic bits are installed correctly, I believe this is where you will run into the alignment problems. because there is 2 plastic pieces that snap together for each screw and they are offset. You have to refer to the manual to determine which way they should be installed. If I recall, the offset should be towards the outside for all 4 corners pushing the screws outward.

6) after assembling the screw clips and you install the screws, then put the metal ring over the pump and from the other side, snap the plastic ring into the metal ring, THIS REQUIRES A BIT OF EFFORT TO DO

7) Then at that point, you should be ready to set the pump on top of the CPU and screw the screws into the back plate I STARTED THE OPPOSITE HOLES FIRST, IT TOOK A BIT OF EFFORT BUT IT WORKED FINE.





Look at this picture from the ANTEC manual. you need to make sure that the clips are installed in such a way that the screws are furthest away from the pump

Clear as mud??? blinksmiley.gif

Hope this helps.

Those two are now included in the OP smile.gif
post #4262 of 6068
TangoDown332, Forumla Z is a beast motherboard, you're good to go thumb.gif.
Quote:
Originally Posted by inedenimadam View Post

Just a heads up...

Microcenter has the 620's on sale for 49.99.

I almost picked a couple up, but I wanted to do a little more reading about using them as GPU cooling units.

I've been looking into this a lot as well, it's typically a 20-30C temp reduction over stock GPU coolers. Also some GPU's require a copper shime between the GPU chip and kuhler cold plate (7950/7970 I believe and some 600 series nvidia cards) because the chip is recessed below some metal surrounding the chip.

Nice TD applaud.gif
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
post #4263 of 6068
Quote:
Originally Posted by M3TAl View Post

TangoDown332, Forumla Z is a beast motherboard, you're good to go thumb.gif.
Quote:
Originally Posted by inedenimadam View Post

Just a heads up...

Microcenter has the 620's on sale for 49.99.

I almost picked a couple up, but I wanted to do a little more reading about using them as GPU cooling units.

I've been looking into this a lot as well, it's typically a 20-30C temp reduction over stock GPU coolers. Also some GPU's require a copper shime between the GPU chip and kuhler cold plate (7950/7970 I believe and some 600 series nvidia cards) because the chip is recessed below some metal surrounding the chip.

Nice TD applaud.gif

Sounds like I will need the shims then mad.gif
At 50 bucks I might give it a shot anyway, but I will still need to figure something out for VRM and Memory.
Blue540
(14 items)
 
x99
(18 items)
 
B.M.O.
(10 items)
 
CPUMotherboardGraphicsGraphics
6800k ASUS X99-A EVGA 980 FTW ACX 2.0 EVGA 980 FTW ACX2.0 
RAMHard DriveHard DriveCooling
Corsair Vengeance CMK32GX4M4B3200C16W Crucial MX100 WD Blue 1TB EK Supremacy EVO 
CoolingCoolingCoolingOS
EK 480 PE EK 240 PE EK D5 Vario Windows 10 
MonitorKeyboardPowerCase
Samsung 49KU7500 (curved 4k) Corsair K65 NZXT Hale 90 V2 1000W Thermaltake X9 
MouseMouse Pad
Logitch G100S X-Trac Ripper 
CPUMotherboardGraphicsRAM
6400k msi A75MA-P33 Sapphire 6670 passive hynix 2 GB dual channel 
Hard DriveOSMonitorKeyboard
WD  windows 8.1 e-machine wireless 
PowerCase
king win 600w custom built 
  hide details  
Reply
Blue540
(14 items)
 
x99
(18 items)
 
B.M.O.
(10 items)
 
CPUMotherboardGraphicsGraphics
6800k ASUS X99-A EVGA 980 FTW ACX 2.0 EVGA 980 FTW ACX2.0 
RAMHard DriveHard DriveCooling
Corsair Vengeance CMK32GX4M4B3200C16W Crucial MX100 WD Blue 1TB EK Supremacy EVO 
CoolingCoolingCoolingOS
EK 480 PE EK 240 PE EK D5 Vario Windows 10 
MonitorKeyboardPowerCase
Samsung 49KU7500 (curved 4k) Corsair K65 NZXT Hale 90 V2 1000W Thermaltake X9 
MouseMouse Pad
Logitch G100S X-Trac Ripper 
CPUMotherboardGraphicsRAM
6400k msi A75MA-P33 Sapphire 6670 passive hynix 2 GB dual channel 
Hard DriveOSMonitorKeyboard
WD  windows 8.1 e-machine wireless 
PowerCase
king win 600w custom built 
  hide details  
Reply
post #4264 of 6068
Quote:
Originally Posted by SinatraFan View Post

OK,,,

As I recall, when I first used it on my AMD board with a FX-8150 chip:

1) I removed the fan bracket that was installed on my MSI MOBO.

2) I put the 2 adhesive strips on the rectangular plastic back plate that came with H20

3) Installed the metal nuts into the back plate

4) Installed the back plate to the back side of the MOBO

5) when you assemble the pump fastener ring, make sure the plastic bits are installed correctly, I believe this is where you will run into the alignment problems. because there is 2 plastic pieces that snap together for each screw and they are offset. You have to refer to the manual to determine which way they should be installed. If I recall, the offset should be towards the outside for all 4 corners pushing the screws outward.

6) after assembling the screw clips and you install the screws, then put the metal ring over the pump and from the other side, snap the plastic ring into the metal ring, THIS REQUIRES A BIT OF EFFORT TO DO

7) Then at that point, you should be ready to set the pump on top of the CPU and screw the screws into the back plate I STARTED THE OPPOSITE HOLES FIRST, IT TOOK A BIT OF EFFORT BUT IT WORKED FINE.





Look at this picture from the ANTEC manual. you need to make sure that the clips are installed in such a way that the screws are furthest away from the pump

Clear as mud??? blinksmiley.gif

Hope this helps.

I own the AMD version of the 920 cooler and I found that with my Athlon II x4 that I had to do away with the plastic parts as they held the screws to far away from the bottom plate.
The plastic upper portion of the thumb screws have a bottom lip that fits right into the slot in the hold down bracket. So if your having trouble getting the screws down into the bottom plate below the motherboard just toss the plastic parts fit the lip of the thumb screws into the slot and slowly adjust the tension to the CPU per the instructions.
Edited by sparkeyjames - 5/15/13 at 6:17pm
post #4265 of 6068
Quote:
Originally Posted by inedenimadam View Post

Sounds like I will need the shims then mad.gif
At 50 bucks I might give it a shot anyway, but I will still need to figure something out for VRM and Memory.

Shims are only $2-4 but if you will be using the 7850 it doesn't require a shim, just 7950's and 7970's.

To better explain/show how a shim is required for some GPU's look at this pic from EK Waterblocks.


So you would put thermal paste between shim and GPU then paste the waterblock and shim. From what I've read shims don't affect temps at all or only very slightly.
Edited by M3TAl - 5/15/13 at 6:58pm
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
post #4266 of 6068
Quick question, how does the orientation of the rad for the 920 affect performance if at all and is there any specific orientation that should be used. I am trying to get some info on this because I will be getting a Thermaltake water 2.0 Pro soon ( wanted the 920 couldn't get it this was next best ) and I want to mount the rad upside down if at all possible.

I am asking here because from what I can gather both the 920 and the water 2.0 Pro are mare by Asetek so I am assuming what is relevant to the 920 will be relevant to the water 2.0 Pro.

Thanks in advance
biggrin.gif
White Knight
(21 items)
 
  
CPUMotherboardGraphicsRAM
i5 3570k MSI z77 Mpower Gigabyte GTX 980ti G1 Gaming Corsair Vengence 
Hard DriveHard DriveHard DriveHard Drive
OCZ Vertex 4 Seagate 1TB Sata6 Western Digital 1TB Green Samsung Spinpoint F4 2TB 
Hard DriveOptical DriveCoolingOS
Seagate Green 2TB LG External Drive Thermaltake Water 2.0 Pro Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
LG D2343 IPS LED LG D2343 IPS LED Corsair K70 RGB Corsair TX750m 
CaseMouseMouse PadAudio
Coolermaster Storm Stryker Corsair M95 Corsair MM400 Sennheiser HD558 
Audio
ASUS Xonar STX 
  hide details  
Reply
White Knight
(21 items)
 
  
CPUMotherboardGraphicsRAM
i5 3570k MSI z77 Mpower Gigabyte GTX 980ti G1 Gaming Corsair Vengence 
Hard DriveHard DriveHard DriveHard Drive
OCZ Vertex 4 Seagate 1TB Sata6 Western Digital 1TB Green Samsung Spinpoint F4 2TB 
Hard DriveOptical DriveCoolingOS
Seagate Green 2TB LG External Drive Thermaltake Water 2.0 Pro Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
LG D2343 IPS LED LG D2343 IPS LED Corsair K70 RGB Corsair TX750m 
CaseMouseMouse PadAudio
Coolermaster Storm Stryker Corsair M95 Corsair MM400 Sennheiser HD558 
Audio
ASUS Xonar STX 
  hide details  
Reply
post #4267 of 6068
Thread Starter 
Hey man, the position of the rad or res won't affect performance in all honesty, however it is recommended, to avoid bubbles, to have it facing down, thus not against gravity - as it might have bubble noises down the line (for short periods of time)
post #4268 of 6068
So the only possible downside to an upside down mounted rad is water noise from time to time (Possible water noise)? No performance issues?
White Knight
(21 items)
 
  
CPUMotherboardGraphicsRAM
i5 3570k MSI z77 Mpower Gigabyte GTX 980ti G1 Gaming Corsair Vengence 
Hard DriveHard DriveHard DriveHard Drive
OCZ Vertex 4 Seagate 1TB Sata6 Western Digital 1TB Green Samsung Spinpoint F4 2TB 
Hard DriveOptical DriveCoolingOS
Seagate Green 2TB LG External Drive Thermaltake Water 2.0 Pro Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
LG D2343 IPS LED LG D2343 IPS LED Corsair K70 RGB Corsair TX750m 
CaseMouseMouse PadAudio
Coolermaster Storm Stryker Corsair M95 Corsair MM400 Sennheiser HD558 
Audio
ASUS Xonar STX 
  hide details  
Reply
White Knight
(21 items)
 
  
CPUMotherboardGraphicsRAM
i5 3570k MSI z77 Mpower Gigabyte GTX 980ti G1 Gaming Corsair Vengence 
Hard DriveHard DriveHard DriveHard Drive
OCZ Vertex 4 Seagate 1TB Sata6 Western Digital 1TB Green Samsung Spinpoint F4 2TB 
Hard DriveOptical DriveCoolingOS
Seagate Green 2TB LG External Drive Thermaltake Water 2.0 Pro Windows 7 Ultimate x64 
MonitorMonitorKeyboardPower
LG D2343 IPS LED LG D2343 IPS LED Corsair K70 RGB Corsair TX750m 
CaseMouseMouse PadAudio
Coolermaster Storm Stryker Corsair M95 Corsair MM400 Sennheiser HD558 
Audio
ASUS Xonar STX 
  hide details  
Reply
post #4269 of 6068
Cooling performance will not change depending on rad position.
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
DeskoSaurus X
(22 items)
 
It Does Stuff
(24 items)
 
 
CPUMotherboardGraphicsRAM
4790K 4.7 GHz Z97 MPOWER MAX AC 290X Lightning G. Skill TridentX 2x8GB 10-12-12 
Hard DriveHard DriveCoolingCooling
2x Crucial MX100 + 960GB M500 2x WD Blue RAID EK Supremacy EK-FC R9-290X Lightning 
CoolingCoolingCoolingOS
EK XE 480 + EK CoolStream PE 480 10x Phanteks + 2x Cougar Vortex MCP50X + MCP50X Windows 10 Pro 
MonitorKeyboardPowerCase
ViewSonic VX2250 22" LED Generic HP Corsair AX860i Lian-Li DK-Q2X 
MouseMouse PadAudioOther
Logitech G700 XTRAC Ripper TC Electronic Impact Twin Corsair Commander Mini 
OtherOther
Schiit Vali Kanto Yumi (Bamboo) 
CPUMotherboardGraphicsRAM
FX-8350 4.95GHz 24/7 GA-990FXA-UD3 Sapphire 7870 XT  Mushkin Redline 997051 @1866 8-8-8-24 1T 
RAMHard DriveHard DriveCooling
Crucial Ballistix Tactical Tracer @1866 8-8-8-2... Black WD6401AALS 2x WD10EZEX Raid-0 EK Supremacy 
CoolingCoolingCoolingCooling
10x Cougar Vortex PWM 3x Helix EK VGA Supremacy Acetal Alphacool NexXxos ST30 240mm, 2x XT45 240mm XSPC X2O 750 
CoolingOSMonitorKeyboard
Jingway DP-600 pump Windows 8.1 Pro x64 ViewSonic VX2250 22" LED Generic HP 
PowerCaseMouseAudio
Rosewill HIVE-650 CM 690 II Advanced B&W  Logitech G700 Xonar DG 
AudioOtherOther
Tc Electronic Impact Twin Fan Controller: Aerocool X-Vision 2x Swiftech PWM Splitter 
  hide details  
Reply
post #4270 of 6068
Quote:
Originally Posted by Rosco321 View Post

So the only possible downside to an upside down mounted rad is water noise from time to time (Possible water noise)? No performance issues?

I will say if every H2O is magically topped off perfectly and there is almost no air then yes, you're right, but WHY TAKE THE CHANCE? I would say because the system is in solid tubing with NO windows, you would never really know if there are air bubbles with the exception of the pump noise. I say that you should always try to mount it in any position EXCEPT with the tubes on top. But that's just me. upsidedwnsmiley.gif
    
CPUMotherboardGraphicsRAM
Intel Core i7 3930K Big Bang-XPower II (MS-7737) ASUS HD7970 Series Corsair  
Hard DriveHard DriveOptical DriveCooling
Seagate Barracuda OCZ Agility 4  LG DVD burner Antec Kuhler H20 920 
OSCaseOther
Microsoft Windows 7 Pro 64 bit Cooler Master HAF-X recon fan controller 
  hide details  
Reply
    
CPUMotherboardGraphicsRAM
Intel Core i7 3930K Big Bang-XPower II (MS-7737) ASUS HD7970 Series Corsair  
Hard DriveHard DriveOptical DriveCooling
Seagate Barracuda OCZ Agility 4  LG DVD burner Antec Kuhler H20 920 
OSCaseOther
Microsoft Windows 7 Pro 64 bit Cooler Master HAF-X recon fan controller 
  hide details  
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Water Cooling
Overclock.net › Forums › Cooling › Water Cooling › [Official] Antec Kühler H2O 620 & 920 Owners Club