|
![]() |
Overclock.net - Overclocking.net > Cooling > Water Cooling | |
D-Tek Fuzion install tip!
|
||
![]() |
|
|
LinkBack | Thread Tools |
|
|
#1 (permalink) | ||||||||||||
|
Stinger Slinger
![]()
Join Date: Jan 2006
Location: Mount St. Helens slope
Posts: 2,729
Rep: 295
![]() ![]() ![]() Unique Rep: 168
Trader Rating: 30
|
The Fuzion uses flat rubber seals instead of o-rings. These seals are a product
of injection molding, unfortunately, not all molding slag is removed prior to WB assembly. The bottom plate seal isn't critical since it is not exposed to water. However, the inner side of the top seal is completely exposed to water flow. So, if you plan to purchase a D-Tek, I would suggest you dissasemble it and remove the slag before installation. Unless you want this crap in your pumps impeller:
__________________
"Semper in excreta sumus solum profundum variat." www.Stinger Water Blocks... Tube clamp selection Guide ... Ira-K's WC PDF Guide ... Fuzion pre-install tip... Stinger Tribute
Last edited by Dryadsoul : 05-06-07 at 12:19 AM |
||||||||||||
|
|
|
|
#2 (permalink) | ||||||||||||||
|
Scarring Your Psyche
![]() |
I shoulda known you'd have one of those by now
![]() Thanks for the tip!
__________________
Quote:
|
||||||||||||||
|
|
|
|
#3 (permalink) | ||||||||||||
|
Stinger Slinger
![]()
Join Date: Jan 2006
Location: Mount St. Helens slope
Posts: 2,729
Rep: 295
![]() ![]() ![]() Unique Rep: 168
Trader Rating: 30
|
Yeah, got it for a C2D shootout next month against the V8 and D/O.
__________________
"Semper in excreta sumus solum profundum variat." www.Stinger Water Blocks... Tube clamp selection Guide ... Ira-K's WC PDF Guide ... Fuzion pre-install tip... Stinger Tribute
|
||||||||||||
|
|
|
|
#4 (permalink) | ||||||||||||||
|
Scarring Your Psyche
![]() |
That oughta be an eyeopener.
Have you tried it out yet? Is it low restriction? I am thinking about downsizing the pumps in my builds...$100 for the MCP 655 is killing me... Whadday think would a Petra modded d-2 or 3 do it with a Fuzion?
__________________
Quote:
|
||||||||||||||
|
|
|
|
#5 (permalink) | ||||||||||||
|
Stinger Slinger
![]()
Join Date: Jan 2006
Location: Mount St. Helens slope
Posts: 2,729
Rep: 295
![]() ![]() ![]() Unique Rep: 168
Trader Rating: 30
|
Yeah, it's way low restriction, that Petra modded DDC+ should be just the ticket.
__________________
"Semper in excreta sumus solum profundum variat." www.Stinger Water Blocks... Tube clamp selection Guide ... Ira-K's WC PDF Guide ... Fuzion pre-install tip... Stinger Tribute
|
||||||||||||
|
|
|
|
#7 (permalink) | |||||||||||||
|
Testing addict
![]()
Join Date: Jan 2007
Location: Klamath Falls, OR
Posts: 2,551
Rep: 580
![]() ![]() ![]() ![]() ![]() ![]() Unique Rep: 281
Trader Rating: 0
|
Yeah, thanks for the tip +1, I'll plan on taking mine apart when it gets here next week.
__________________
|
|||||||||||||
|
|
|
|
#8 (permalink) | ||||||||||||
|
Habitual Tinkerer
![]() |
Thats pitiful....Just goes to show why you need to take them apart and look of r crud...Can't wait for the shoot-out...
__________________
Quote:
...i͏̢҉r̶̨̛͜a̶͘͡-̨̛k̵̴҉̵̀E8500 @ 5736Mhz **OCN Water Cooling Club And Picture Gallery **E8600 @ 5751Mhz
|
||||||||||||
|
|
|
|
#9 (permalink) | ||||||||||
|
AMD Overclocker
![]() |
you got me re-tinking my idea of going with the apogee GT .. hmm. I think Ill wait for the shootout to decide 100%
__________________
|
||||||||||
|
|
|
|
|
#10 (permalink) | ||||||||||||
|
Stinger Slinger
![]()
Join Date: Jan 2006
Location: Mount St. Helens slope
Posts: 2,729
Rep: 295
![]() ![]() ![]() Unique Rep: 168
Trader Rating: 30
|
Hey, the original Apogee Extreme had the same problem with mill tailings and broken pins.
And the Fuzion runs top of the world after clean up.
__________________
"Semper in excreta sumus solum profundum variat." www.Stinger Water Blocks... Tube clamp selection Guide ... Ira-K's WC PDF Guide ... Fuzion pre-install tip... Stinger Tribute
|
||||||||||||
|
|
![]() |
| Tags |
| cleaning, d-tek fuzion |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|