Flow Rate Estimator Spreadsheet V1.7 - Page 3 - Overclock.net

**dr4gon** · 07-19-07

Quote:

Originally Posted by DuckieHo

Preesure Drop vs Flow Rate.... the faster the water flows through the rad, more resistence will occur which slows down the flow. (higher is bad)

Heat Dissipated vs Flow Rate.... the faster the water flows through the rad, the more heat it can handle. (higher is good)

Thermal Resistence vs Flow Rate.... the faster the water flows through the rad, the easier it is to transfer heat. (Higher is bad)

thanks and repped!

Martinm210 · 07-21-07

Version 1.3 is up...bunch more components to pick from.
http://www.overclock.net/2441593-post1.html

Side note:

D-tek GFX GPU block takes the crown as the most restrictive block

Thermochill rads take the crown as the least restrictive.

Dryadsoul · 07-21-07

Great work there Martin. I may not get that V8 out till the 1st.
If you can use a bonnie, I have an extra that's yours.

Martinm210 · 07-21-07

Quote:

Originally Posted by Dryadsoul

Great work there Martin. I may not get that V8 out till the 1st.
If you can use a bonnie, I have an extra that's yours.

Not a problem, plenty of other things to keep me busy, no rush.

Yes, a bonnie would be sweet! I've been hoping to put a third loop together, that would get me off in the right direction. And I'll go ahead and run a pressure drop curve on it, I'm pretty sure they are just as good as most rads out there for flow rate and may even beat out a couple of the more restrictive ones.

Thanks!

Martinm210 · 07-27-07

Couple more components and pumps, see first post for V1.4

**Burn** · 07-28-07

Great work Martin- I need to get Office installed

Will try uploading to google spreadsheets and see if it works.

Edit- Published it online for you via Google Spreadsheets- http://spreadsheets.google.com/pub?k...OvAw2YQJ9a7TTw

The forumulae compute, but the images aren't viewable :\

**ira-k** · 07-28-07

Crap I cant get that one to work either...At least I can see what it looks like now...

..

Martinm210 · 07-29-07

Quote:

Originally Posted by Burn

Great work Martin- I need to get Office installed

Will try uploading to google spreadsheets and see if it works.

Edit- Published it online for you via Google Spreadsheets- http://spreadsheets.google.com/pub?k...OvAw2YQJ9a7TTw

The forumulae compute, but the images aren't viewable :\

Thanks!
Just need to figure out how to make it interactive without having to edit.

Martinm210 · 07-30-07

Man, I've tried everything I could think of to get this thing on the web. What I could do in the first version is now giving me errors, might have to upgrade office to 2007 and see if that gives me any better abilities.

Anyhow, I added a few pumps - DDC1, DDC1 pro top, RD20, RD30 and put 1.5 up.

Martinm210 · 08-05-07

FYI V1.6 has been added
http://www.overclock.net/water-cooli...et-v1-4-a.html

V1.6 Added:
MCW-6002
D-Tek Whitewater - LE
DDC-1 9W (Alphacool Reservoir Top)
DDC-1 18W
DDC-1 18W (Alphacool Pro Top)
DDC-1 18W (Alphacool Reservoir Top)
D5 Basic (D5 setting 4)

V1.6 Updated:
-Tubing Curves, pressure drop tested all three types and updated curve to reflected collected data, this will overally give very slightly higher results, and the gap between 7/16" and 1/2" is narrower.
Also did some houskeeping on the tables to make additions less painful

		Overclock.net - Overclocking.net > Cooling > Water Cooling
Flow Rate Estimator Spreadsheet V1.7

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)