Ticko311

ok so i am about 2 hours into my 2nd day of bleeding the system...i feel as if i have more air bubbles then when i started does it normally take this long ... am i doing something wrong or is there something wrong with my system?

__________________

Board: Asus 590 SLI AM2
CPU: AMD Athlon 64 X2 Dual Core 6400+ Black Edition
PSU: antec 1kw 90amp
GPU: eVGA Nvidia GeForce 9800GX2 SSC
HDD: 40/80GB Samsung IDE HDD - 100GB Maxtor DymondMax SATA HDD - 300GB Western Digital Caviar
RAM: 2x 1gb OCZ SLI DDR2

ira-k

With a res it should of been bleed in a few hours at the most, Are you keeping coolant over the res barb? Are your tube to barb connections all tight? Is the return, suction line from your res to the pump connections good and tight? Thats really where it would be most likely to suck air back into your loop...

You have to keep enough coolant in your res so that it wont keep sucking air back into your loop through the barb...

I'd turn it off for a little while and see if the foam will die down a little...Feel your pump and see if its hot, if it is you need to shut it down and let the pump cool off, its not good to let it keep pumping foam for a long time...

__________________
**Water Cooling Essential Threads**Relay Wiring **480 GTX-Temp's w/wo Shrouds **TEC Essential Threads

** E8600 @ 5.75Ghz 10x **E7200 @ 4.5Ghz 9x **5000BE @ 3.5Ghz 10x**150 Opty @ 3.2Ghz 12x**

Ticko311

alright i checked most of that stuff and all tight i changed out the fluid earlier today and already seen an improvement in airbubbles i think i had some sort of gunk in my last fluid or something that a rinse of the parts took care of that was causing it to foam with air bubbles but thanks for everyones help i think its almost done ill post on here later to tell you how it turns out

__________________

Board: Asus 590 SLI AM2
CPU: AMD Athlon 64 X2 Dual Core 6400+ Black Edition
PSU: antec 1kw 90amp
GPU: eVGA Nvidia GeForce 9800GX2 SSC
HDD: 40/80GB Samsung IDE HDD - 100GB Maxtor DymondMax SATA HDD - 300GB Western Digital Caviar
RAM: 2x 1gb OCZ SLI DDR2

Tufelhunden

Can't wait to see the reults, we like pics.

__________________
Folding For The Cure and OCN under Tufelhunden

ira-k

If you didn't clean out your rad before you used it you can have problems like that...I usually get some white looking crud out of them, I don't know if its left over soap scum from leak testing or flux or whatever, its nasty junk...

Hope it will bleeds out right for you now....

__________________
**Water Cooling Essential Threads**Relay Wiring **480 GTX-Temp's w/wo Shrouds **TEC Essential Threads

** E8600 @ 5.75Ghz 10x **E7200 @ 4.5Ghz 9x **5000BE @ 3.5Ghz 10x**150 Opty @ 3.2Ghz 12x**

Ticko311

ok got everything worked out and no bubbles FINALLY! my temps have lowered dramatically it was nice to see the 28c for a few minutes when i first booted but now idle is about 32-36 with the side pannel on so not too shabby under full load doesnt push more than 38 so i am happy thanks for your help guys and hopefully ill be able to throw some pics up tonight stupid sister has the digi camera

__________________

Board: Asus 590 SLI AM2
CPU: AMD Athlon 64 X2 Dual Core 6400+ Black Edition
PSU: antec 1kw 90amp
GPU: eVGA Nvidia GeForce 9800GX2 SSC
HDD: 40/80GB Samsung IDE HDD - 100GB Maxtor DymondMax SATA HDD - 300GB Western Digital Caviar
RAM: 2x 1gb OCZ SLI DDR2

ira-k

Good deal...I'm glad to hear that......We love pic's....

__________________
**Water Cooling Essential Threads**Relay Wiring **480 GTX-Temp's w/wo Shrouds **TEC Essential Threads

** E8600 @ 5.75Ghz 10x **E7200 @ 4.5Ghz 9x **5000BE @ 3.5Ghz 10x**150 Opty @ 3.2Ghz 12x**

Tufelhunden

Very cool!! Really glad to hear that!

__________________
Folding For The Cure and OCN under Tufelhunden

MikuMiku

i would put my input but tufel has said alot. Ira can be very helpful too

__________________
http://www.gamexe.net/signatures/0sig_future.png