Tufelhunden

I like these.

Others swear these are better and for the money they better be.

__________________
Folding For The Cure and OCN under Tufelhunden

Metal425

I have a question, how will I go about getting the power to the rad with it to the rad box? How am I going to get it to plug inside the case, and power up the x3 120mm fans for the Rad?

__________________

GRID Drift Club

Tufelhunden

Assuming the leads on the fans aren't long enough you could always solder in extensions. You might be able to get away with crimps, I just prefer solder especially for smaller wiring.

__________________
Folding For The Cure and OCN under Tufelhunden

ira-k

I'd use some 86cfm Pana, they are $10 bux each here.86cfm Pana...You can really get by with any 47+ cfm fans on the GTX, I'd use decent 120x38mm fans, they have a higher pressure and will scavenge air through the rad a lot better.360 GTX Beats PA.3 w/47cfm Fans..HWlabs 480GTX thermals-Martin

Shrouds help on a GTX or any thick or higher fin per inch rad...

.. Poll: Push or pull configuration for Radiators

..Part-1-480 GTX-Temps W & W/O Shrouds

..How To: Make any Sized shroud in 2 minutes

..How To: Build A Performance Shroud

Just make a long 4-pin molex and run it out to your rad fans...

These are some other good shops, I buy gear from them all the time..Look around and find stuff on sale, it will save you some $$$.

..Sidewinders

..Jab-tech

..Danger Den

..SVC.

__________________
**Water Cooling Essential Threads** Overclock.net's Downloads Section** TEC Guide:Basic Principles of TEC's

**E7200 @ 4141*9**5000BE @ 3510*10**LE 1600 @ 3500*10**150 Opty @ 3242*12**

Metal425

How's this so, Rad= http://www.petrastechshop.com/hwlablicegts1.html


Will this work for the v1? http://www.petrastechshop.com/qucomiinford.html

I was planning on getting a v1 Fuzion, but I'll maybe get the v2 here. http://www.petrastechshop.com/dfuv2uncpuwa.html

I ordered 3 Feet of http://www.frozencpu.com/products/71...cid_Green.html for now, I'll probably get 7 feet in a couple days.


http://www.xoxide.com/swiftech-mcres-micro.html=Res

And the pump, I have decided on yet.

__________________

GRID Drift Club

Metal425

I also might take the plunge and get a GPU Water Block, but I don't want it yet, I'll wait for my second 8800GT.

__________________

GRID Drift Club

Metal425

If I need to Water-Cool 2 Card, and a CPU, will a 360 work?

__________________

GRID Drift Club

ira-k

The GTS is a real restrictive rad, I wouldn't use one a multi-block loop at all...

The quad insert is for the V2 only...

I would go ahead the get the V2...Its a little improved and comes with a back-plate...

I would get a D-5 vario pump...D-5 Vario.

A 360 GTX with higher cfm fans can handle a CPU and 2 GPU's, but I would either go with the 480 GTX for it, or 2 loops...480 GTX

__________________
**Water Cooling Essential Threads** Overclock.net's Downloads Section** TEC Guide:Basic Principles of TEC's

**E7200 @ 4141*9**5000BE @ 3510*10**LE 1600 @ 3500*10**150 Opty @ 3242*12**

Metal425

What about just for cooling my CPU only?

__________________

GRID Drift Club