DIRTYDUCK

I can't thing of an easier way to seal that block m8! I doubt there is one.

__________________
Got F@H?

Don't be shy click the link!

Hueristic

Yup but wait 15 minutes after snugging it down so it can "cure" before fully tightening. And I recommend Ulta Copper RTB.

__________________
FOLDING under LicheLord
Take a Shot at this!
¡¡¡ʍʇɟ qn1ɔ uoıʇɐıɔǝɹddɐ 939 ʇǝʞɔos ǝɥʇ

This goes without saying but
1. If you can't afford to lose it don't mod or OC it.
2. At least read the OP before commenting, Having a clue doesn't hurt either.
Semper Fi

ira-k

Yeah a o-ring would be great if you can get it done cheaply..Did you ever lap the top down flat like DD was suggesting? That might be part of the problem if its not really good and flat..Where is it leaking at?

__________________
**Water Cooling Essential Threads**Relay Wiring **480 GTX-Temp's w/wo Shrouds **TEC Essential Threads

** E8600 @ 5.75Ghz 10x **E7200 @ 4.5Ghz 9x **5000BE @ 3.5Ghz 10x**150 Opty @ 3.2Ghz 12x**

azt3c

Here are some temps, they were not great but was my the first block design :P
and i was not using good fans, just 4 50mm and 2 80mm fans were the only ones that i had, but it's just to compere between the enzotech and mine.

Evercool Iceman 2x90mm@1600rpm


Enzotech block



My Home-Made Black

nafljhy

thats not bad at all though! only 3C diff between the enzo and yours homemade block.

__________________
I Fold, Do You?

Projects: Valkyrie - Serenity - Techstation - FaHRack
dellaVostro: CPU-Z Valkyrie: CPU-Z

Stuff to Sell - WC Accesories

azt3c

you think so ? :S
tomorrow i will try to make another kind of block, i have to push it until i get the same numbers as the enzo or better if i can.

nafljhy

yea, i do think its really good for a homemade block! i wish you luck on lowering it down! hope you do! that would just be awesome.

__________________
I Fold, Do You?

Projects: Valkyrie - Serenity - Techstation - FaHRack
dellaVostro: CPU-Z Valkyrie: CPU-Z

Stuff to Sell - WC Accesories

azt3c

Guys, is a good or bad idea if i 75% of that water that does not have mineral or anything and 25% pure alcohol ?

DIRTYDUCK

I think if you heat up alcohol it expands...no? I would be afraid it would pop my tubing off my block.

__________________
Got F@H?

Don't be shy click the link!

ira-k

Very nice temp's, I missed you post......Thats really good temp's you have with ti..You might have a future as a block smith..

Unless your running a chiller and have to have it as a anti-freeze, I wouldn't use alcohol, it can mess up your rubber o-rings and gaskets, it might not either, but its a chance you would be taking..

__________________
**Water Cooling Essential Threads**Relay Wiring **480 GTX-Temp's w/wo Shrouds **TEC Essential Threads

** E8600 @ 5.75Ghz 10x **E7200 @ 4.5Ghz 9x **5000BE @ 3.5Ghz 10x**150 Opty @ 3.2Ghz 12x**