H80 / H80i / H90 / H100 / H100i / H110 Case Compatibility Thread (Page 1 for full listings) - Page 25 - Overclock.net - An Overclocking Community

Forum Jump: 

H80 / H80i / H90 / H100 / H100i / H110 Case Compatibility Thread (Page 1 for full listings)

Reply
 
Thread Tools
post #241 of 1518 (permalink) Old 01-29-2012, 08:04 AM
New to Overclock.net
 
joeyck's Avatar
 
Join Date: Jun 2010
Posts: 225
Rep: 6 (Unique: 5)
http://www.youtube.com/watch?v=JzyKRifUPrg

Fits in the antec 1200 push/pull but u can only get two screws in but it is rock solid.

so if it fits inside the 1200 it will fit in the DF 85 as they have the same size minus like .5 inch in some areas, and the same fan size as one other on the back (120mm)

Enjoy smile.gif

and read the comments fully as people have posted how this will affect / not affect the PCI. its a great video!

joeyck is offline  
Sponsored Links
Advertisement
 
post #242 of 1518 (permalink) Old 01-30-2012, 03:40 PM
New to Overclock.net
 
toyz72's Avatar
 
Join Date: Oct 2009
Location: florida
Posts: 2,913
Rep: 110 (Unique: 93)
Quote:
Originally Posted by Mattyd893 View Post

Any pics?

sorry took so long. this is my fractal design arc mini. as you can see the h100 is push/pull but, for the rear fan you'll need a 120x12mm fan. other than that , there is no mod's needed.
400
400
400

toyz72 is offline  
post #243 of 1518 (permalink) Old 01-30-2012, 10:01 PM
New to Overclock.net
 
Taiwanese's Avatar
 
Join Date: Nov 2011
Location: Planet Earth
Posts: 243
Rep: 3 (Unique: 3)
Quote:
Originally Posted by toyz72 View Post

sorry took so long. this is my fractal design arc mini. as you can see the h100 is push/pull but, for the rear fan you'll need a 120x12mm fan. other than that , there is no mod's needed.
400
400
400

Do you think a H80 would fit on the rear of that case? :O
Taiwanese is offline  
Sponsored Links
Advertisement
 
post #244 of 1518 (permalink) Old 01-30-2012, 11:50 PM - Thread Starter
New to Overclock.net
 
Join Date: Jul 2011
Posts: 984
Rep: 87 (Unique: 80)
Quote:
Originally Posted by Taiwanese View Post

Do you think a H80 would fit on the rear of that case? :O

Yes you can, here's a link: http://forums.overclockers.com.au/showpost.php?p=13440020&postcount=12 although if you're buying new and have the extra bit of cash, i'd reccomend the H100

@everyone else, OP updated with additional info, thanks for the inputs.

There's no such thing as a stupid question..... Only stupid answers!
Mattyd893 is offline  
post #245 of 1518 (permalink) Old 01-31-2012, 07:39 AM
New to Overclock.net
 
joeyck's Avatar
 
Join Date: Jun 2010
Posts: 225
Rep: 6 (Unique: 5)

600T push/pull.

Very slight mod (I dont even think its considered a mod lol)

joeyck is offline  
post #246 of 1518 (permalink) Old 02-02-2012, 12:09 AM - Thread Starter
New to Overclock.net
 
Join Date: Jul 2011
Posts: 984
Rep: 87 (Unique: 80)
Thanks, nice vid. OP updated!

There's no such thing as a stupid question..... Only stupid answers!
Mattyd893 is offline  
post #247 of 1518 (permalink) Old 02-02-2012, 05:05 PM
New to Overclock.net
 
wheresstimpy's Avatar
 
Join Date: Nov 2011
Location: California
Posts: 104
Rep: 2 (Unique: 2)
i can confirm it will fit in a Rosewill Thor push pull but you better be handy with a dremel and a drill if you want to use tall ram and full sized fans in push pull. The biggest problem with this case is that the motherboard sits so high in the case. It really limits what you can do on the top area. They really didn't design it to have anything other than the one 230mm fan (stock) or the optional two 140mm (or 120mm) fans (well i guess i shouldn't say they, since we all know Rosewill didn't design this case, lol). With my parts combination i was forced to push the h100 as far over (away from the motherboard) as possible so i would have clearance. The h100 will bolt up to stock holes but it is too close to the motherboard in push pull. Once it is moved over you will need to cut away the material blocking the fans ( i cut the mesh too while i was at it). Then you need to drill some mounting holes, i only needed to drill 4 and then use washers to hold the other side through the mesh(closer to the motherboard). This is pretty solid and looks nice if you take your time. Then all that's left to do it remove the center plastic clips from the case top on the side you just covered up and trim any material away from the top where the bolts are so it will fit flush (all hidden once its together).


448448448
wheresstimpy is offline  
post #248 of 1518 (permalink) Old 02-02-2012, 06:28 PM
New to Overclock.net
 
phillyd's Avatar
 
Join Date: Oct 2011
Location: Louisville, KY
Posts: 7,362
Rep: 188 (Unique: 146)
Quote:
Originally Posted by wheresstimpy View Post

i can confirm it will fit in a Rosewill Thor push pull but you better be handy with a dremel and a drill...
h100cut.JPG 62k .JPG file
wizbang.JPG 94k .JPG file

you probably could have done this with low profile fans on the original screw mounts if you had either one set of fans or the rad and a set of fans on the top of the case.

Ryzen & Vega Enthoo Evolv ATX TG Case Mod Build Log
Audio (Click to show)
Sources: The Spectre | Lenovus Maximus | Huawei Honor 8
DAC's: HiFimeDIY Sabre SPDIF | iBasso D-Zero
Amplification:ASL MG-Head OTL Mark III
Headphones: Sennheiser HD650 | Shure SE215K | Logitech UE6000
Speakers
Home Theater/Lenovus Maximus: Pioneer Elite SC-85 > Music Angel SDXE M9 > Klipsch KG5.2 w/Crites tweeters/crossovers
The Spectre: Adam Ax7
Build Logs (Click to show)Overclocking Accolades (Click to show)


phillyd is offline  
post #249 of 1518 (permalink) Old 02-02-2012, 11:47 PM
New to Overclock.net
 
toyz72's Avatar
 
Join Date: Oct 2009
Location: florida
Posts: 2,913
Rep: 110 (Unique: 93)
still have not updated the h100 to the fractal design arc mini. there more than one mini. the picture i linked is an arc mini. mine is mounted in the top. comon matt biggrin.gif

toyz72 is offline  
post #250 of 1518 (permalink) Old 02-03-2012, 12:22 AM - Thread Starter
New to Overclock.net
 
Join Date: Jul 2011
Posts: 984
Rep: 87 (Unique: 80)
Quote:
Originally Posted by toyz72 View Post

still have not updated the h100 to the fractal design arc mini. there more than one mini. the picture i linked is an arc mini. mine is mounted in the top. comon matt biggrin.gif

Done... stop your whining biggrin.gif

Other posts added as well.

There's no such thing as a stupid question..... Only stupid answers!
Mattyd893 is offline  
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off