The AMD How To Thread - - An Overclocking Community
Forum Jump: 

The AMD How To Thread

Thread Tools
post #1 of 439 (permalink) Old 06-04-2012, 12:10 AM - Thread Starter
Join Date: Feb 2010
Location: Goin back to Cali
Posts: 21,556
This will be for collecting all the How To's in one place. If you have something to add let me know and I will gladly add it.
Here's some stuff to start things off.

**Doing some updates to this thread since Afterburner has changed so much. I'll leave the old methods spoilered and in tact. It's still very good imo to know the fundamentals behind why we check the boxes that we check in the current Afterburner.


Driver downloads

Driver uninstalls

At this point Display Driver Uninstaller has matured very well and I find myself using it more often than not. It's quick and easy. Also, after extracting it if you run the exe from windows, it will automatically take you to safemode on reboot. It sure beats manually getting the OS to boot to safemode on windoze 8 and higher!

**If you already have AB configured properly, say you went thru this guide already and are swapping to a new driver, remember to set AB to not start with windows. If the hardware does not change and it is just drivers that you are changing, AB will not change the gpu profiles. Simply unchecking start w/ windows will save your settings. After you install the new driver, start AB. Remember to redo the following things, check the boxes for disable ulps and extend official oc limits. This is covered in more detail at the end of the section on configuring AB.

Below is the manual method I used to use when the you know what hits the fan.
Warning: Spoiler! (Click to show)
Run the driver setup.exe, choose uninstall, express. Once completed, do not reboot and go to control panel, run Programs and Features, click on AMD Catalyst Install Manager, click change, next, Express Uninstall All AMD Software, after a second pop up, choose Remove. If anything fails, not much you can do so move on to next step. If you have caps installed, uninstall them as well at this time but do not agree to reboot when it asks you to do so.

**If you installed a modded driver, choose custom and check everything before continuing on.

Now, go to device manger and uninstall the standard vga device or AMD Radeon XXX if you see it. If you choose to clean the registry, you must not skip this step. But don't worry, deleting the devices is safe. If prompted to reboot, choose yes. If you are asked or given the choice to delete the driver, choose to do so. *Something to keep an eye out for is while uninstalling the vga devices, if you are unlucky windows will black out, ie. the screen goes black. Do not freak out, this is just an annoying bug because we just uninstalled the drivers, and then deleted any leftover drivers in the windows driver subsystem. If you have vnc and another pc, you can use that to remote into your rig and continue the uninstall process. If not, just hit the power button once, only once to initiate soft shutdown. Reboot, then continue where you left off.

At this point, you have the option of blasting all the old radeon gpu keys if you want to or are OCD like me. I can't stand having more keys than I have cards and it's just so dirty looking.
Warning: Spoiler! (Click to show)
Anyways, open regedit and go to:


You can simply delete the whole folder 4D36E968-E325-11CE-BFC1-08002BE10318, It will fail but conveniently for us it will wipe the subfolders for us. You can also delete the ControlSet002 folder ie. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet2\Control\Class\{4D36E968-E325-11CE-BFC1-08002BE10318} in the same manner but it's not a big deal.

* If for some reaason you only want to delete the active card or cards, you can open these folders. The active cards will have a sub folder DAL2_DATA_2_0. Inactive folders will not have this folder.

You don't have to mess with ControlSet1 as it is replicated with CurrentControlSet and vice versa. ControlSet002 will need to be manually cleaned however.

Now back to device manager.

**This portion deals with deleting the leftover driver files. I would recommend in most day to day situations to skip this portion as it's not needed. The dll's will get overwritten upon driver install anyways. However if you have a situation that you are trying to recover from (failed sweeper/installer) this will remove just the dll associated with the gpu driver. It is best for AMD CPU based users to skip this part as sometimes AMD cpu/mb drivers are tied to the gpu drivers, especially in cases of APU. If you do not use an AMD CPU continue on for the best OCD experience.


Delete everything that starts "ati" then xxxx, everything. For ex. it starts with the file atiadlxx.dll and goes to ativvsvl.dat. There's nothing there that starts ati that isn't driver related. If there are files locked, skip them and move on. Now you are ready to reboot, upon logon windows will install default vga device and ask to reboot.

**There may be some dll's that were not deleted previously due to them being loaded in memory during the file deletion. You can safely delete those after reboot, once Windows has re-installed the standard vga driver if you so choose, depending on your OCD level.

Upon reboot, you will be at a clean state, or that is 99% clean of AMD drivers.

Driver install

Thankfully this is the easiest part of AMD driver process. If you use an SSD boot device and have a secondary drive for your games/etc then change destination folder drive to that drive. For ex, I simply change the C: to D:. It will create an AMD folder on your D: drive. I also use this folder to store my downloaded drivers. I also keep the extracted folders for later, driver reinstalls. You can go back and run the setup.exe for each driver at will.

Now as the install progress, choose Install, then custom. Custom allows you to inspect the options. I run an eyefinity setup so I don't want to use the raptr stuff. I don't need it changing my game specific settings, etc. Let it finish and reboot.

Configuring Afterburner 4.0 and higher

There are basically two ways to overclock on AMD gpus, unofficial and official. Unofficial used to be the predominant way to overclock, but these days and with the improvement in AB, the official method has become quite reliable. Here I will detail how to setup AB using official method, and setting up profiles which are vitally important to a running well behaved gpu.

After installing Afterburner. Run it and AB will ask to check the gpus and reboot. Allow it to do it's thing. Upon reboot, run AB again and check all the boxes like I have in the pic below. Check them and do not mix modes. Afterburner will again ask to reboot. Allow it to do so.

After configuring like so, you then need to setup two presets under the profiles tab under settings (the settings button). One profile is default (ie. stock clocks untouched) and one is for your oc/daily settings/whatever use, etc. You can create more profiles at will. Now go to settings/profiles and pick your default preset for 2D profile and other preset for 3D profile. Exit AB, and restart it to save settings. Your card should now drop down to low power clocks while idle, and conversely maintain the clocks you chose for the 3D profile under load. Btw, be sure to max Power Limit on your 3D profile. This is important to prevent throttling. Also, do not forget to enable unified gpu monitoring.


*If you have a MSI Lighting, you can change the drop down box next to "unlock voltage control" to extended MSI.

**In the latest version, 4.1.1 correction formulas have been added to various processes for ex. under monitoring. Let's take vram usage which is a global output that displays total vram usage. But this can be confusing at a moments glance especially in game. By using the correction formula while you are setting up vram usage monitoring, we can tell AB to divide the vram usage by the number of gpu we have in crossfire. Thus for quads type in the correction formula box: x/y where x = vram usage and y = the number of gpus. Thus our equation to type into the box is x/4 for quads or x/3 for tri and x/2 for dual. You'll know whether its wrong or not because the text will turn red when the equation is incorrect syntax.

RTSS setup and profiles

Here is where you can setup the Onscreen Display (OSD). I generally don't want to see a bazillion stats while gaming, though I will add that the more sensors monitored, the more lag you will introduce. Something to keep in mind is that the stats that you want to see in the OSD are setup in Afterburner under settings/monitoring. But controlling what apps initiate 3D clocks is done from the RTSS app itself. And very important too is how do you know what app/apps are requesting 3D clock status? You can find that by clicking the "i" button at the top of the AB window next to the card/driver name. Below I will show how to control what apps are allowed 3D access using RTSS.

^^Here you can see waterfox is using hw acceleration even when its disabled. Nice job Mozilla!

We can use RTSS to add known offender apps like your browser, specifically Mozilla browsers to the profile list and set them to none for app detection level. This will prevent Firefox from using hw acceleration even though you've already unchecked the acceleration box inside Firefox. Mozilla often changes how they use HA between builds, so version 30 did not trigger HA, but version 31 does. And all the while you had no idea since you unchecked HW accel in settings anyways, but it is still using it lol. Mozilla browsers are a pain in the ass. This process is a great tool in your toolbox

Click on the big plus sign and add the *.exe of the app in question. You can either traverse to the file.exe or just type the filename.exe. RTSS will work with either method. Then change it's app detection level from low/whatever to None. That's it, you've now disabled that app's access to gpu acceleration.

Reinstalling drivers with no HW changes w/o reinstalling Afterburner

After following the steps above and if there are no hw changes to your gpus before running DDU, open AB and uncheck start with windows. The profiles created by AB will not change but running AB in the middle of a driver update can cause headaches. After DDU and installing the new driver, you can start AB again and re-check the box to start with windows. Be sure to re-check disable ULPS and extend official overclock limits.

**Old methods with more detail

Warning: Spoiler! (Click to show)

AMD clock control files **Only need with uinofficial method.

RC11 extracted files

RC11 338k .zip file

**Extract to system32 and syswow64 directories, C:\windows\system32 etc and drop the files into your Afterburner directory as well.
Warning: Spoiler! (Click to show)
Afterburner install - unofficial overclock method

*Fyi, beta 6 and higher have had the profile management functionality removed. Please be aware if you are using the beta while trying the methods below.
Warning: Spoiler! (Click to show)
**Assumes you have no instance of AB, aka afterburner installed previously. If you do have AB installed previously, uninstall it or delete the folder. Also, it is generally a good idea to uninstall AB before any new driver install when you are crossfired. AB will automatically run, even when run at windows start is disabled, and when it does and it tries to fool with clocks you will BSOD with a 07E code.

Run afterburner install. At this point, if you choose default install directory, there will incur security issues later on, just keep that in mind. I would recommend you install it in another folder/drive.

After install completes, do not check the option to start afterburner. If you are crossfired follow A- below to disable ULPS if you are using Unofficial Overclock Method (UOM) or , you can skip this portion if you are using Official Overclock Method (-xcl), however be warned that Afterburner will not be able to see your sleeping cards if you have ULPS enabled. Thus it's probably a good idea to disable ULPS anyways.

A- Disabling ULPS
Warning: Spoiler! (Click to show)
Open regedit and go to:


This key 4D36E968, under CurrentControlSet is the only folder you need to access. You can ignore the others, so don't search for it just traverse directly to said folder. It's time to disable ULPS, or ultra low power savings. Inside the folder you will find more folders, 0000/0001/0002/etc so on and on.

Open each folder and double click on EnableULPS and change to 0. You do not need to change any other key, or any keys that look similar, just change EnableULPS. Close regedit. End of A-

At this point if you installed into default directory, you will have a security issue. Open file manager, go to where you installed afterburner and right click on MSIAfterburner.cfg and go to security, click edit, add yourself and give yourself full control, click ok.

Now go back and open MSIAfterburner.cfg in notepad.

Scroll to bottom and change this:

UnofficialOverclockingEULA =
UnofficialOverclockingMode= 0

to this:

UnofficialOverclockingEULA = I confirm that I am aware of unofficial overclocking limitations and fully understand that MSI will not provide me any support on it
UnofficialOverclockingMode= 1

**Note on the mode setting. Some new games are causing clock conflicts with Powerplay creating flickering on the desktop. You can avoid this by choosing 2, instead of 1. I am running with Powerplay off. Look Mom, no flickering. Refer to the bottom of Post 2 for more info on this. biggrin.gif

Close and save MSIAfterburner.cfg. At this point download the file from the link above for AMD Clock Control files and run it. Do not reboot.

Now you can run afterburner for the first time. Afterburner will analyze the gpu asic and ask to reboot when ready. Choose yes to reboot. After reboot, you will have afterburner installed, you can then unlock voltage control and monitoring, etc. Happy overclocking.

Afterburner install - unofficial method - Profile Setup
Warning: Spoiler! (Click to show)
Originally Posted by tsm106 View Post

Open AB, click reset then save that to preset 1. Now create an overclocked setting and save that to preset 2. Once complete, click on settings and scroll right to the Profiles tab. Then using the drop down boxes choose the appropriate profiles.

2D profile: choose the default clock preset 1

3D profile: whatever you want here

Afterburner install - official overclock method aka -xcl Part 1 for single cards Warning: Spoiler! (Click to show)

Install driver of choice. Tri and quadfire people, I'd recommend you stick with RC11 and refer to Part 2 for getting the rest of your cards enabled.

Install AB, I recommend in a different directory from default. In general you will need to install the above linked clock control files. RC11 does not need these files.

On your desktop is the shortcut of AB, make a copy of it to edit. Add -xcl to the end of the target box after right clicking it/properties. Click ok to close the window. Make sure to close AB before running this newly edited shortcut.


"C:\Program Files (x86)\MSI Afterburner\MSIAfterburner.exe" -xcl

After AB's prompt, reboot and save this shortcut and rename it so you have it for safe keeping. You will need to re-run if it you change drivers again.

For some background on the xcl process. The -xcl switch is just to tell AB to create new modified Powerplay Tables in the registry. All it does is unlock the overclock limits of Overdrive. Note you won't be using Overdrive at all. You'll instead be using AB but using AB just as default with only the check marks for unlocking voltage. Don't do anything in AB's config file, that method is for "unofficial method" whereas you'll be using "official method."
When you add -xcl to the AB shortcut, it doesn't run, it merely imports the Powerplay Tables as mentioned above. Once that's done, you have to then remove the -xcl you added, and reboot. Upon reboot, you can open up AB and overclock like normal.
**There are a couple caveats with the -xcl method. The most annoying is that AB cannot edit the Powerplay Tables of more than 1 card. And that 1 card is only the active card so if you have crossfire you will have to jump thru some hurdles. There's a trick to add all the Powerplay Tables for ppl in crossfire in that link.
**The other annoyance is that you will have to redo the -xcl method after each driver install.
**Also, you will need the clock control files.
It's also a good idea if you are crossfired, to do this on a cleaned registry so you know which Radeon folder to edit.Thus the bottom line is we use AB to overclock without enabling UOM and without disabling ULPS. When you set your overclock in AB, this gets passed to Overdrive and you stay inside AMD's Powersaving tech. For voltage control, we use AB as we normally would.

Afterburner install - official overclock method aka -xcl Part 2 for crossfire users - addon Warning: Spoiler! (Click to show)
AB xcl method above will only unlock the Overdrive limits for the active card. If you have other cards in a crossfire, technically you will have to disable crossfire and plug a monitor into each card and run the xcl unlock process to unlock each card. This can be quite the hassle. Luckily there's an easier way.

Anyways, I extracted the powerplay tables allowing one to edit and not do the song and dance.

*Open notepad, copy paste this in there save it as a *.reg file or rename .reg then merge that into your reg. Edit the "0000" for each card you have. Simply paste/create the key below and label each corresponding key 0000/0001/002/etc for as many entries or cards as you have in the registry. Also with this key, you don't have to create the shortcut sd with Part 1.

Windows Registry Editor Version 5.00



**If for some reason it's not working for you, you can simply open up your registry, navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E968. Easy way is Local, System, CurrentControlSet, Control, Class, then scroll down to "4D36E9" set then hit the "68" at the end. Inside you find "0000" files, and each folder represents a physical card per slot. So if you moved card 1 that was in slot 1, into slot 4, that will create a new folder. Try not to move cards around too much because it will create a lot of folders, making it confusing. Also, if you followed my manual uninstall method, your registry should be cleaned up nicely.

Ok, now scroll down to the 4D36E968 folder and extract that folder to some place. Open up some place, and edit the reg file. Basically you just delete everything except the table and header from above. And then simply create more entries as instructed above.

Make Afterburner show real voltage

Show real voltage in Afterburner for 7970s.
Warning: Spoiler! (Click to show)
With Afterburner closed, open your Afterburner install directory, traverse to profiles. There will be a config file for each card or cards inside. If you have more files than cards, then you can just delete all the files, ie. VEN_1002&DEV....cfg. This will effectively reset Afterburner. Now run Afterburner again and it will configure your cards and create new config files. Now you can edit the newly created config files. Close AB and...

Add this under the Settings for each card you have.

VDDC_CHL8228_VIDReadback = 0
MVDDC_CHL8228_VIDReadback = 0

Unlocking and editing voltage on Caymans using RBE - Warning: Spoiler! (Click to show)

Original thread for 6950 to 6970 Mod

Radeon Bios Editor

*Before you start, put RBE, atiwinflash, and you extracted bios file into a folder on the c drive, named unlock.

Start by confirming your card/s are on switch #1. Open gpuz, underneath the AMD icon, next to bios version, click on the green arrowed bios chip button, choose save to file. Save as unlock.rom.

Start Radeon Bios Editor, RBE for short. Click Load Bios, choose your unlock.rom file. Go to the 4th tab, Additional features and under unlock 6950 ->6970, choose to unlock. That was easy!

Now go to the 2nd tab, Clock settings and click o GPU registers (bottom left). View/Change voltage registers window will open and with four boxes. The two on the right are what we are after. Depending on what your asic % is, you will have either both boxes show 1100, or 1100 and 1065. Some cards work with the 3rd box and some with the 4th box. It doesn't really matter so we will change both to whatever voltage you've decided upon.

**Caution Label here. Over 1.3v or 1300mv is only safe with water. 1.4v is the dead zone, do not push your luck. Whatever you choose to put in is your choice.

Once you've edited your volts, click ok, then Save the bios.

Now you are ready for flashing. I prefer to use a dosprompt, I can just copy paste and push the up key to repeat commands for crossfire configs. I can flash four cards in less than 5 minutes this way.

Thus open a admin dos prompt. Text taken from wizzard from TPU.

- Black command prompt windows opens
- Type "cd\"
- Type "cd unlock"
- Type "atiwinflash -unlockrom 0" <-- the 0 means first adapter, if you have multiple cards *change the 0 to the next card in line, etc etc*
- Type "atiwinflash -f -p 0 unlock.bin"
- It should complete the flashing process with a message saying something with "verified".

If you have multiple cards, repeat the process until all cards are flashed. Once completed you are ready for reboot. There should be no driver changes, but confirm you have new shader count in gpuz. Now onto overclocking Caymans.

Overclocking on Cayman using Overdrive Warning: Spoiler! (Click to show)
Racerx mod

The beauty of using RBE is that we get to use AMD's full suite of powersaving tech w/o breaking anything. And what goes hand in hand with RBE is the Racerx mod.

In Post #2 you will find attached two versions of Racerx. One is an old version and the current version. If you find that the current version won't run, you can use the original. The difference is that v16 brings a few of value added features that are nice, but what's most important is just raising the Overdrive limits.

Run racerx, leave everything default except for Upper Limits. Raise that to a sensible upper limit. Click create file and save it, choose yes to apply it to the registery. Reboot and you will have raised Overdrive limits.

*Hopefully you've cleaned your registry out from the above method so you will only have 1 folder if you are single gpu. Thus you need only import the reg file. If however you have crossfire or more, you simply edit the Racerx reg file and create copies of the data making a separate entry for each card.


Copy data and make another entry changing the bolded digit to 1, for the second card, 2 for the third card. If you did not clean your registry you will have to determine what numbers point to which card on your own.

Once done and rebooted, you no longer have to use Afterburner for overclocking. You can however still use it to display OSD stats.

Yahoo, +50 Powertune Warning: Spoiler! (Click to show)
Racerx also has a mod to raise powertune to +50.

Do you still have the racerx.reg file on your desktop?
If not, re-run the tool and when it asks to save it, save it as racerx.reg. you need to add the .reg after the name or it will save it as a generic file, because after it creates it do NOT merge it.

Now, right click on it and click "edit".
This should open it in Notepad.

look down about 4 lines and you'll see the number 14 in between a bunch of zeros.
Carefully change the 14 to a 32, making sure not to change or add any spaces or extra commas.
Close it and let it save it. Then click on it and allow it to merge.
reboot, then CCC should have the 50 back for you.

** Note, this hack can also be applied to AB's clockspeed tables from the -xcl method.

tsm106 is offline  
Sponsored Links
post #2 of 439 (permalink) Old 06-04-2012, 12:17 AM - Thread Starter
Join Date: Feb 2010
Location: Goin back to Cali
Posts: 21,556
Driver tricks per game

You can manually force a game to use X driver by dropping that driver's dll set into the game's folder that houses the game.exe. Where to get these dlls? Each time a driver is installed the dlls are extracted to the windows/system32 folder. The files are named atidxx32.dll/atidxx64.dll and for crossfire aticfx32.dll/aticfx64.dll. Each api type uses a different dll/dll grouping. You'll notice when a game crashes most often it will list the offending driver. That's the driver that was loaded into the game. The trick with this is that we can force the game to use a specific driver or the latest driver if for some reason you prefer to be on a specific driver. There are unfortunately many instances where ppl prefer to one specific driver over another for a variety of reasons from system crashes not specific to games or other reasons. Ah, this brings back old memories of the old days of driver hacking, where we'd mix and match driver dlls with different catalyst version to overcome limitations in the drivers. It didn't always work, but was more often a pain in the ass to do. Here's a way to stay on that lovable driver and still get the gains/fixes from the latest driver in that awesome gameworks title. Luckily for us we don't have to install every driver to get to the dlls or manually extract them by downloading each driver version (unless you've kept a copy of the dlls along the way - hugs for the ocd lol). Someone has done this already for us on guru3d. Below is the link to PrMinisterGR's thread and repository for the dlls. Be sure to go there and thank him for extracting and compressing these dlls.

Archived odd and ends below, mostly retired and/or outdated methodology.

Warning: Spoiler! (Click to show)
Racerx original version 16k .zip file

Racerx v16

RacerX 30k .zip file

Odds and Ends - Observations that I've noticed over time.

- Flickering desktop. If your screens, firefox, browsers start to flicker randomly it might be due to an app kicking the gpu clocks into another powerstate and there was a problem returning to normal 2D clocks. Sometimes you can fix this w/o a reboot by disabling your Eyefinity group and then re-enabling it.

- Powertune settings do not save. There is a bug in some versions of Catalyst where the driver cannot access the powertune/powersettings while ULPS has shutdown the slave cards in cfx. An easy way of getting around this is by running GPUZ in the background. GPUZ will poll the gpus waking them up, giving you access to the cards.

- Flash Youtube Issues
I’m sure I’m not the only one but I’m really surprised to see AMD Catalyst 12.8 WHQL come in 2nd after 8.97 18 April.

If you’re not aware of the Flash problem that’s been going on for quite some time: If you’re having issues with Flash, especially in Firefox, as in the browser freezes when watching videos (ie Youtube) you might be blaming the drivers but that’s not the case. Flash is buggy at best and with hardware acceleration enabled or without it you’re still going to have issues. To fix this you’ll need to disable Protected Mode

Edit mm.cfg and add/edit this line: ProtectedMode = 0
Windows 32bit: C:\windows\system32\macromed\flash
Windows 64bit: C:\windows\syswow64\macromed\flash

12.9 Beta to 12.11 beta 11 driver issues

Desktop flicker, flickering, etc

It's due to the way the driver or AB is handling being pushed into 3D clocks on the desktop. You can avoid this by choosing option 2 at the unlock AB process thereby disabling Powerplay(PP). Note, this only works for those using Unofficial Overclock Method.

open MSIAfterburner.cfg in notepad.

Scroll to bottom and change this:

UnofficialOverclockingEULA = I confirm that I am aware of unofficial overclocking limitations and fully understand that MSI will not provide me any support on it
UnofficialOverclockingMode = 2

What's happening is while a game login screen is on, AB kicks it into 3D mode cuz the game is technically on. However PP see's 3D clocks on the desktop and is like nice try and tries to drop clocks. bam, you get flickering. If you open AB's graph monitoring you'll see the core/memory clocks fluctuating, which causes the flicker. This should be visible on the desktop, like on your way to logging into whatever multiplayer game. Also if you're using unofficial method like me, you don't need Powerplay at all.

Here's a video showing the flicker with Powerplay on and off.

Desktop Crashing with 12.9 beta

If you get the explorer crashes, you can replace this dll in your c:\windows\system32 directory. Remember to rename your original file, for ex atiumd64.dll.old for backup. 1856k .zip file

Sapphire Trixx Mod for memory voltage (Tahiti)

I recommend using Trixx for serious benching, it controls voltage better than AB. AB on the other hand is better for 24/7 use with it's OSD and screenshot/video capabilities.

Sapphire Trixx 3450k .zip file
Sapphire Trixx 3468k .zip file


*Some notes on Trixx. It is a somewhat finicky piece of software. If you push too much voltage, it will trigger OVP (overvoltage protection) and the card will throttle. Sometimes Trixx just doesn't run right and it bogs the bench. You can compare this situation by simply closing it, give it a min then run AB. A reboot usually solves the issue.

**Trixx is somewhat specific to Sapphire cards in the sense that it is for some cards the only way to get voltage control. Trixx can also be used on reference cards. And in regards to Hawaii gpu, it is the easiest way to get +200mv w/o having to own a MSI Lightning. MSI allows Lightnings to apply +200mv within Afterburner w/o having to resort to adding LLC via the command line. If you are on Hawaii gpu, just download the latest Trixx from

PSU Problems

Recently I had a problem with my psu, the 3.3v rail was dropping down 3.2v or less for no reason. It also impacted my eyefinity setup, the rig would drop out of eyefinity when overclocked within 5 minutes. It took a few days of ignoring it then a few days of actual diagnosis which came up with nothing. I was about to pull my hair out when I remembered about my sleeved extensions. I swapped them out and used the stock cables. Voila, it works again. The 3.3v rail is now putting out 3.3v or better and eyefinity with max overclocks works w/o a hitch. If you are experiencing similar issues, remember to check your cables.

tsm106 is offline  
post #3 of 439 (permalink) Old 06-19-2012, 07:09 PM
New to
nvidiaftw12's Avatar
Join Date: Aug 2011
Posts: 6,888
Rep: 238 (Unique: 191)

Hmm. I can defalt set my power tune to +50. Also, I find it is way better to uninstall drivers via ATIman vs self-uninstaller.

nvidiaftw12 is offline  
Sponsored Links
post #4 of 439 (permalink) Old 07-06-2012, 12:00 AM
New to
error0024's Avatar
Join Date: Feb 2007
Posts: 148
Rep: 1 (Unique: 1)
Is it safe to set the powertune to +50% though?...

error0024 is offline  
post #5 of 439 (permalink) Old 07-06-2012, 12:37 AM
New to
nvidiaftw12's Avatar
Join Date: Aug 2011
Posts: 6,888
Rep: 238 (Unique: 191)
Originally Posted by error0024 View Post

Is it safe to set the powertune to +50% though?...


nvidiaftw12 is offline  
post #6 of 439 (permalink) Old 07-06-2012, 03:26 AM - Thread Starter
Join Date: Feb 2010
Location: Goin back to Cali
Posts: 21,556
Originally Posted by error0024 View Post

Is it safe to set the powertune to +50% though?...

It was more of a gimmick on the Sapphire Toxic (maybe others now) which had a +50 slider. The OCP and OVP control maximum TDP via voltage and clock control, so even if it really worked, which is still in question, you'd be throttled anyways once you tripped the protections. When that happens the card will lock and will no boot until you restart. Sometimes it will take a while too.

tsm106 is offline  
post #7 of 439 (permalink) Old 10-18-2012, 06:47 PM
New to
SilkyJohnson's Avatar
Join Date: Mar 2012
Location: The middle of hell, MS
Posts: 276
Rep: 12 (Unique: 9)
Thanks for the info it fixed my issues I was having with screen flickering and if my explorer crashes anymore ill try the other fix as well.

What is real? How do you define real? If real is what you can feel, smell, taste and see, then 'real' is simply electrical signals interpreted by your brain.
SilkyJohnson is offline  
post #8 of 439 (permalink) Old 10-20-2012, 08:52 PM
New to
killakris's Avatar
Join Date: Mar 2012
Location: Modesto, CA
Posts: 486
Rep: 28 (Unique: 23)
thanks alot for this, showed me how to properly unlock afterburner and got rid of the screen flickering problem ive had for months, and solved my OCing problem on windows 8, which would keep crashing my system

killakris is offline  
post #9 of 439 (permalink) Old 10-27-2012, 11:23 AM
New to
KaRLiToS's Avatar
Join Date: Jan 2010
Location: Québec, Montréal
Posts: 9,054
Rep: 959 (Unique: 560)
Great Update on your guide tsm106


??? ? ? ?⌨️??? ???

KaRLiToS is offline  
post #10 of 439 (permalink) Old 10-30-2012, 07:52 AM
New to
heroxoot's Avatar
Join Date: Nov 2011
Location: TN
Posts: 1,587
Rep: 26 (Unique: 23)
I disabled ULPS and all my flickering on 12.11 driver vanished. Also the idle bug is fixed b using HDMI over DVI. The bug only exists when using a DVI connector on your monitor. I say, on your monitor, because I used dvi > hdmi and it fixed the bug.

heroxoot is offline  

Quick Reply

Register Now

In order to be able to post messages on the - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page

Forum Jump: 

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off