|Topic Review (Newest First)|
|01-24-2020 02:27 AM|
|x7007||does anyone have stuttering with with smt in COD MW? because I am getting stuttering compare to no smt. sometimes it takes a game but it always happens.|
|01-24-2020 01:48 AM|
|myionzolo||I have solved with LLC AUTO, with procODT 48, RTT_NOM RZQ/7 and 34, RTT_WR OFF and RTT_PARK (48)RZQ/5 now i want try extreme profile someone say tell me is dangerous to use dram voltage at 1.51V?|
|11-07-2019 08:57 AM|
Is it possible to switch Boot VGA adapter?
I'm on ubuntu and I want to pass-through my GPU on first slot PCIe to a Qemu KVM, however if I do vfio-pci the first slot VGA, ubuntu will hang at boot. I don't really want to disable VGA on my ubuntu host, as I do use desktop environment rn...
|11-06-2019 05:55 PM|
Can anyone tell me if they have tried this new utility Armory Crate on the support page of the Zenith Extreme page? it states to uninstall aura so this reinstalls it? and now is part of that utility or what? I still have some problems with my live dash so I was thinking in give it a try to that but want to know if someone have try it and what is the outcome.
|11-06-2019 05:48 PM|
|10-05-2019 12:16 PM|
Hi all! Tell me please how to properly overclock the memory to 2933 frequency? What timings to set and so on? I am using two G.Skill F4-3600C17D-32GTZR kits.
specs (if needed)
cpu: threadripper 2990wx
mb: ze ofc (bios ver 2001)
psu: rog thor 1200
|10-04-2019 04:58 PM|
what are you using to measure? aida 64 cache & memory benchmark? I did make a test after updating to 2001 Bios and for what I recall I didnt change too much anyway my results are kinda average.
I havent had any problems on that side, in fact I'm trying to adjust my voltages, are you using Load Line Calibration ? if yes in what setting ? are you stock on the cpu ?
AIDA stability test freezing after 5 seconds, i figured it might be aida64 ver 6 architecture might not be compatible with the board and TR updates however i need to do my research on that one, its unusual that one stress test from one software fails .. while real world ( Maya 3D 4K rendering ) eats all RAM and CPU cores like a monster yet still stable
|10-02-2019 12:27 AM|
I just flashed the BIOS on my ZE today, with the latest version 2001.
I noticed that although the RAM is stable now at 3200 Mhz (before it was unstable for more than 30 minutes) the latency increased from 66 ns to 89 ns.
Anyone else experienced the same thing? Also the READ speed dropped by 15 GB/sec or something .. from 92 to 78 GB/sec. The write speed stayed the same.
P.S. I'm using 2 x32 GB kits form G.Skill Ripjaws 3200 Mhz , CL14 which are Samsung B-Die dual sided. The timing is set manually to 14 - 14 - 14 -14 - 34 - 44 and 1T command rate (no gear down or power down). Basically I copied all the settings from the previous BIOS and applied to the new one increasing only the frequency to 3200 Mhz from 3066 Mhz.
|10-02-2019 12:20 AM|
I was getting the same hangs on boot, checked a lot of stuff in depth and eventually found my DRAM AB voltage was 0.02-03V lower than what it should be (running XMP). I bumped it up to 1.38 and no more random hangs - hwinfo reporting it now sits at 1.35 with occasional very short spikes to 1.37. Lots of variables and we're probably running different ram but it might be worth double checking to see if that's the problem.
I havent manage to make the oled screen work again (stuck on "small text")...
EDIT: Im on Bios Version 2001
|09-30-2019 07:55 AM|
Bad experience with this new BIOS update on my side as well. Although I have increased the frequency for the DRAM from 3066 Mhz to 3200 Mhz keeping the exact same settings for the the timings CL14 1T, i actually get a performance drop on the Read and increase in latency from 65ns to 88 ns or something like that.
Overall is less stable than the previous version.
I think i will roll back to the previous one because this one is ****.
|This thread has more than 10 replies. Click here to review the whole thread.|