Overclock.net - An Overclocking Community - Reply to Topic

Thread: Sapphire RX580 4gb Nitro+: Flashed my Custom BIOS. 2-3 weeks after being stable it now crashes at start. Stock bios appears to work fine. Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-20-2017 06:15 PM
richardcore
Quote:
Originally Posted by The EX1 View Post

Did you check for memory errors after altering fhe memory timings and clocks? Just because the card ran, doesn't mean the memory wasn't throwing tons of errors out. Use HWINFO to check for memory errors in case you haven't. If you ran the card 24/7 for weeks with memory that was tossing up millions of errors, I can see that causing degredation.

Yeap, I did check it. None of my GPUs run with errors, some of them will get like 6 to 20 in 15min or so. So that wasn't it. I'm running the stock bios fine for couple days now and it seems stable. The old bios is a no go, memory clocks that go high will immediately fail the card.
10-18-2017 10:56 PM
The EX1 Did you check for memory errors after altering fhe memory timings and clocks? Just because the card ran, doesn't mean the memory wasn't throwing tons of errors out. Use HWINFO to check for memory errors in case you haven't. If you ran the card 24/7 for weeks with memory that was tossing up millions of errors, I can see that causing degredation.
10-16-2017 04:54 PM
richardcore So, I made a custom BIOS for my RX 580, it was getting 30mh/s dual mining with DCR and everything was great, life was good. 2 or 3 weeks into it, failed my first card, couple days later, the second card failed as well. Both had similar mods: 2000mhz memory speed with custom straps, undervolted on bios and lower core clock.

About the problem:
1) if i open claymore to start mining now I get almost immediately a black screen
2) i tried a new custom bios I made, flashed it giving about stock figures voltages and powetune, also decreasing memory speed to 1900mhz --- same thing. Fails immediately or soon after starts mining. No change.

I tried switching BIOS on switch and it seems to work fine. I played a game for about 10 minutes. Also mined for >1h now and also good... I will run furmark later for a while and see how it works. At 1750mhz it seems to be fine so far, but stock rom is that disappointing 24mh/s.

Here's the BIOS I made and was using on one of the cards til it failed (ran fine for 2 or 3 weeks great hashrate): http://xonedigital.com/dump/bios1.jpg


This is the stock bios i made backup and recently re-flashed: http://xonedigital.com/dump/bios-stock.jpg



I think I have a decent understanding for OC'ing in general, all my other RX models are doing fine for longer than these cards, but I have very limited knowledge in electronics. I'm confused. What I don't get is: It seems the card damaged something, because it worked great for 2-3 weeks and now it fails almost immediately with the same bios. How can it be damaged if I only used lower voltages? Shouldn't it damage ONLY if I used higher voltages and temperatures? From what I read, it seems that the memory is what's causing trouble as I've seen the type of squary artifact on the screen after the problem started when using my modded bios. How can my memory be bad now if it wasn't running at higher voltage? I even undervolted 100mv... Could it still be damaged? The card ran cooler than stock as it was undervolted. Does running memory at higher than stock speeds and tighter timings decrease its lifespan even if undervolted?

Appreciate your inputs.

Thanks!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off