|Topic Review (Newest First)|
|01-21-2013 05:02 PM|
even with the h100 in push pull going out the top and 5 intake fans i couldnt get it stable @4.4 with reasonable temps using mx-4. the vcore-1 (in asus turbov evo) just goes through the roof (80c). so ive gone the other way and under-clocked to 1.26250 running stable @4 min core temps about 19c max 44c.
|05-01-2012 07:16 PM|
i have the same proc, mobo, and heatsink, and i run roughly 59-60c on load with my fans running @ 1000rpm (roughly 75% speed)
idles im around 38-41c which is higher than im used to idling at, but my fans are around 400-500 RPM and silent as well
AS5 paste because i had it
|05-01-2012 08:18 AM|
|phillyd||probably early next week|
|05-01-2012 12:13 AM|
I have that same DD block that you have. I lost about 5° by going to a Raystorm recently. When's yours going in?
|04-30-2012 08:30 PM|
|phillyd||I'm chillin @4.7 but im under water, and i have a total of 8 fans in my case|
|04-30-2012 08:26 PM|
I got the same, processor and mobo as yours matt but using a thermalright silver arrow heatsink. So far i am able to get mines stable at 4.4ghz with max temp of 48c (core temp) on full load with prime for 6 hours.
22.0x200 @ 4.4ghz
CPU V @ 1.5125
LLC set on regular power.
NB HT @ 1.250 (had to bump it up because system would hang)
CPU/NB @ 2200
HT LINK @ 2600
I haven't messed with it for almost 3 months now but since i have a max temp of 48c I'am kind of inclined to pump more out of it.
The LLC settings are kind of confusing though, it mixes in with the voltages a bit. I can get instabilities and extremely high temps with that so I just left it on low. I'm going to play with the LLC and voltages a bit more and see if I can find a good equilibrium. I will have to lower the voltage if I increase LLC though.
|04-13-2012 01:23 AM|
1.35v 4.3ghz after h100, 19c min 49c max on medium corsair setting. 2x cougar fans push, 2x corsair fans pull, the corsiar fans are very loud.
before the h100 i had 1.35v 4.3ghz, 29c idle 53c load, using the hyper 212 evo with cougar fans in push pull... more updates to come.
|04-08-2012 08:54 PM|
after drilling a few holes the xspc rx360 will fit...a h100 wont be an issue.
nothing is final yet, h100 isnt here, im at 1.35v 4.3ghz, 29c idle 53c load. hopefully with the h100 i can get some more out of it.
thanks 2advanced, its mostly the case but it did take some time. might pull the board when the h100 arrives and reroute the cpu power cable.
|04-08-2012 03:25 PM|
|2advanced||So what is your final speed, voltage peak, and temp? Your computer looks freaking awesome, BTW! I wish mine looked like that...|
|04-08-2012 12:32 PM|
I bought one recently to just make sure it fits your chassi and also invest in some more fans for push & pull.
My idle temp is 8c @ 4.4 Ghz hardly go above 38+ when i'm playing games.
|This thread has more than 10 replies. Click here to review the whole thread.|