Overclock.net - An Overclocking Community - Reply to Topic

Thread: Swiftech H220/H320/H220X/H240X/H140X and CM Glacer 240L/360L Owners' Club Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
09-21-2019 11:24 AM
ciarlatano
Quote: Originally Posted by Herp123 View Post
Does anyone have any luck with the G1/4 adapter for the H220X?
Seems to be more rare than a unicorn..
It's been discontinued for several years. A lot of asks in this thread, but I haven't seen anyone actually finding one. If you stay with 3/8" ID tubing, they are really unnecessary.
09-21-2019 10:30 AM
Herp123 Does anyone have any luck with the G1/4 adapter for the H220X?
Seems to be more rare than a unicorn..
08-29-2019 01:54 PM
ubbernewb i talked to tech at swiftech he said it should be FULL
08-29-2019 01:44 PM
ubbernewb Madmaxneo is was saying i have a waterkit allready installed but am removing it to install the x3, also does it come totaly full? i thought the tubes were colored white but nope it the fluid it seems like it at least has some so, wondering if need to top it up or its probably full
08-29-2019 01:31 PM
Heuchler
Quote: Originally Posted by ubbernewb View Post
just double and triple checked thats only 1 i have not the other will it work on am4 or do i need to call swiftech? for other mount set?
Looks like the correct screws are pre-installed on the AMD bracket (only need to change them if you are going Threadripper). Just undo the four screws on top of you motherboard. keep the motherboards backplate.

Adjust the screws on the AMD bracket to match the motherboard holes. Screw everything back together in an x pattern (hopefully you put the CPU and TIM in at some point). Some motherboard makers glue their backplate to the board.

if not, temporarily secure it tape, cardboard box, old copy of computer shopper or double side tape for something more permanent. worst case ask somebody to hold for you.
08-29-2019 12:59 PM
Madmaxneo
Quote: Originally Posted by ubbernewb View Post
also my old water kit is still in so to fill what should i plug it into? my old kit is using cpu fan can i just use any other header to run it so i can fill it?
I am not sure exactly what you are asking but normally you remove the unit from your PC to fill it. It's a lot easier that way. It also makes it a bit easier to remove the block from the CPU but leave all the tubing intact.

But (and there's always one of those), I always have difficulty filling it all the way without any bubbles unless I do the following:
1. Turn the power off at the PSU and remove the AIO from the PC.
2. Drain and fill the unit with the appropriate fluid.
3. Sit the unit outside your PC with the tubing still in tact.
4. Disconnect the power to the motherboard. If you don't do this then the PC will attempt to start and will fault due to not having anything to cool the CPU.
5. Connect the power header for your Swiftech AIO.
6. Ensure the unit is standing up so that the fill port is pointing upwards and open it.
7. Cycle the PSU on with the PSU switch let it run for a couple seconds then turn it off. Some bubble should release out the top.
8. Fill it (should only be a few drops at a time.
9. Repeat steps 7 & 8 as needed until the unit is mostly full. It is good to leave a tiny bit of space for expansion when and if the water gets warm.
10. Once you have it filled enough close it up and turn the power on and let it run for an hour. this is to check for leaks. If there are no leaks reconnect everything back into your PC.
11. Run your PC but CHECK FOR LEAKS often over the next day or so. In fact it may be a good idea to set some paper towels below the unit to see any minor leaks that may be happening.

Remember to fix all leaks no matter how minor right away!
08-29-2019 12:14 PM
ubbernewb just double and triple checked thats only 1 i have not the other will it work on am4 or do i need to call swiftech? for other mount set?
08-29-2019 12:02 PM
ubbernewb
Quote: Originally Posted by Heuchler View Post
Second bag should be AMD mount.


Swiftech AP-XL-AMD4-BKT AMD Socket AM4 Mounting Hardware
Attachment 292324



Swiftech AMD-TR4-02 for Socket SP3 and TR4 and previous AM4 AM3 and AM2
Attachment 292326
all i have for mounts is the bottom pic, pic says tr4 does that work on am4?
08-29-2019 11:57 AM
Heuchler
Quote: Originally Posted by ubbernewb View Post
swiftech x3 aio is this what i use to mount on am4? the bag they are on shows intell but seems to be only thing to screw to it on top? second pic doesnt say which mount its for?

Second bag should be AMD mount.


Swiftech AP-XL-AMD4-BKT AMD Socket AM4 Mounting Hardware
Attachment 292324



Swiftech AMD-TR4-02 for Socket SP3 and TR4 and previous AM4 AM3 and AM2
Attachment 292326
08-29-2019 11:42 AM
ubbernewb is this using stock amd backplate? this video doesnt show attaching anything to back of board?
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off