Overclock.net - An Overclocking Community - Reply to Topic
Thread: The Walter White home office Reply to Thread

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-22-2015 09:23 AM
Originally Posted by SgtMunky View Post

Look's sweet bruh?

What's the issue with vaping?

Smoked for nearly 20 years. Vaping is a great alternative. And hey, it stopped me from smoking at all, quit about a year and a half ago.
07-28-2015 03:17 PM
Originally Posted by mistersprinkles View Post

Looks good. Toe those speakers in a little bit. Have you considered MoPads?

No room at all on the left side where my case is to turn the speakers at all. Sounds good where they are.
Originally Posted by Punjab View Post

Wow, hittin the vape pen(s) all day huh?


Although I am low on juice right now, I need to make some more.
07-27-2015 06:40 AM
SgtMunky Look's sweet bruh?

What's the issue with vaping?
07-25-2015 08:58 PM
Punjab Wow, hittin the vape pen(s) all day huh?
07-25-2015 07:12 PM
mistersprinkles Looks good. Toe those speakers in a little bit. Have you considered MoPads?
06-22-2015 04:48 PM
taowulf It has been a busy couple of months. My contract that was supposed to run to the end of October was abruptly terminated two weeks ago, and I found out today that it might resume in the next 2-4 months, but no telling what will happen now. Well, back to the job search.

Of course, the best way to get over this set back is to do a little desk modification, and as the Alesis Elevate 5 speakers I ordered a while back came in today, seemed like a perfect time to start the edge banding as I had to cut down the monitor stand a little and decided to make some platforms for the speakers to sit on.

A pic of the whole desk, still organizing some things, but I have cleared the counter behind me pretty much and this is as probably as pristine as my desk will ever be.

Left side from my point of view -

You can see the white edgebanding... I will work on the lower sections of the desk later.

And the right side -

05-26-2015 04:44 PM
Originally Posted by s7Design View Post

Looking good there thumb.gifthumb.gifthumb.gif

Thanks man!
05-26-2015 03:58 PM
s7Design Looking good there thumb.gifthumb.gifthumb.gif
05-25-2015 08:35 PM
taowulf Well, quite a bit more done today, was able to pick up a 6 foot piece of trim to use as a shim, then trimmed the side pieces up to get them to fit...Had to lose a 1/4 of an inch on 5 seperate pieces.

Really pissed that I knocked a little of the veneer off of the desktop on such an obvious corner...but I was having issues manhandling some of the pieces the last two days.

Working on fitting the side pieces...

Hours later, some swearing and in need of painkillers, here is how things are pretty much right now. I still have a ton of organizing to do and to figure out if I am going to put shelves in the side sections next weekend or find some other organizing option.

Also added a LED light underneath the center section of the monitor stand.

Oh, I will probably add the white trim I picked up next weekend. Need to locate an iron for it. smile.gif
05-25-2015 02:53 AM
taowulf I didn't make much progress today. I realized that the pieces where the seats cushions used to be are 1/4 of an inch lower in the rear than the front. Thanks, Fleetwood!

So tomorrow, er...today I will pick up some 1/4 inch trim pieces to use as shims, then I will be off to the races again and should be able to complete everything. Step one will be complete and I will be able to move on to my next project which is replacing horrible soft tubing with hardline. That probably won't be until late June or July.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off