Overclock.net - An Overclocking Community - Reply to Topic

Thread: Testing The OCC LN2 Chiller Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-22-2016 08:03 AM
Duality92 HCP-1300 is great, I have one and it's a boss of a PSU.
02-22-2016 07:58 AM
tatmMRKIV they suck and they are overrated out the ass for their cost and I hear they fail spectacularly when they do fail. Taking out lots of hardware


also something was jacked up about the i series for extreme OC.

its been a while since I looked into them though. but they are definitely not as good as the antec. and I doubt as good as the x2 supernovas

I forget the exact thing, one of the asian pros had found a problem with the i series IIRC, though.

but as I said this was a year or 2 + when I was looking at PSUs.
I got 3x g2 1300 supernovas back then @ 150 a pop and havent had an issue so never needed to get another psu since

also from they way I have seen them treat people who RMA their premier ram kits I wouldn't give them a dime.

or just the way they sell their ram kits at all makes me steer clear.
I know a few people other than me who went in and got the orange c16 3400 dom plats(1000$ a kit MSRP) and they were either previously opened or they were just thrown inside the OEM box with little regard for their safety.

I had a stick that was just jammed into the tray.; it wasn't even in the slot. the sku sticker on it was messed up(I wouldn't have been able to rma it. I sent it right back to where I bought it)

for PSU questions talk to shilka or twocables
02-22-2016 07:04 AM
xxbassplayerxx
Quote:
Originally Posted by tatmMRKIV View Post

corsair sucks

They may be overrated and a lot of people are annoyed at how often the name is thrown out, but they definitely do not suck. Especially if you get one of their higher-end units.
02-22-2016 06:47 AM
tatmMRKIV evga g2 1300 supernova
they are cheap and good.
for expensive and good go for http://store.antec.com/highcurrentpro/hcp-1300-platinum.html

iirc its the best out


corsair sucks
02-22-2016 06:42 AM
xxbassplayerxx If you want a big PSU, I'd recommend the EVGA 1600P2 or 1600T2 or the Corsair AX1500i.

They're pricey, though! I have an older AX1200 and it works pretty well for my needs... though I may be looking to RMA it in the near future. The 5V line is drooping badly.
02-21-2016 11:57 PM
phasechanger
Quote:
Originally Posted by xxbassplayerxx View Post

On the L batches, 5.3GHz fully stable wouldn't be too far off the mark for a bad chip (most could do 5.4-5.5 fully stable on LN2) but the J batches are usually 5.6+ capable on cold.
Picked up a new RVE... how fun! The chip is a j batch. Now I see that my power supply can't keep up with the voltage. Currently using 850 watt Thermaltake. Did 5630 mhz on 8 cores but think found the bottle neck of the 850w PSU and wasn't able to go much further. OCC chilled like a king though. [URL=http://hwbot.org/submission/3135682_[/URL] We'll pick up a 1300-1500w PSU in a week (any suggestions?) and really see what this chip can do. But we should have some good OCC chilled results up from our colleagues before then! . . .
02-01-2016 07:44 PM
phasechanger New Vid - Showing the OCC process from set-up to three HWBOT Benches.
12-27-2015 09:41 AM
xxbassplayerxx
Quote:
Originally Posted by phasechanger View Post

-125 to -140C. No. Next time i freeze it, I'll log the batch #. Stay tuned Bass! .... oh, that was a good Freudian slip redface.gif
On the L batches, 5.3GHz fully stable wouldn't be too far off the mark for a bad chip (most could do 5.4-5.5 fully stable on LN2) but the J batches are usually 5.6+ capable on cold.
12-23-2015 08:04 PM
MunneY Glad to see things progressing!
12-23-2015 07:49 PM
phasechanger -125 to -140C. No. Next time i freeze it, I'll log the batch #. Stay tuned Bass! .... oh, that was a good Freudian slip redface.gif
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off