Overclock.net - An Overclocking Community - Reply to Topic

Thread: 2080 Ti - Working Shunt Mod Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-18-2019 10:43 AM
JackCY
Quote: Originally Posted by dante`afk View Post
welll< I don't have a multimeter, can this not be answered without?

FE card
Not without knowing what card you are actually asking about.
You can look at the PCB closely and try trace it with your eyes, it's best to verify with any continuity meter anyway as to which resistor leads to which connector.
03-18-2019 08:07 AM
Renegade5399
Quote: Originally Posted by Kalm_Traveler View Post
Won't boost as high and might damage the pcie slot on the motherboard.
That one is for the 75W PCIe slot limit like Kalm said. You risk damaging your motherboard. I would remove that ASAP and put it in the proper location.
03-18-2019 07:30 AM
Kalm_Traveler
Quote: Originally Posted by dante`afk View Post
thanks. I ****ed up and put the shunt on the bottom of the front, not to the one who is nearer to the PCI-E connecors. what are the implications of that? It's not going into safe mode for me?
Won't boost as high and might damage the pcie slot on the motherboard.
03-18-2019 07:24 AM
dante`afk thanks. I ****ed up and put the shunt on the bottom of the front, not to the one who is nearer to the PCI-E connecors. what are the implications of that? It's not going into safe mode for me?
03-14-2019 01:54 PM
Asmodian
Quote: Originally Posted by LCRava View Post
Do you guys recommend using the stock Strix 2080 Ti vBIOS with the Shunt Mod or a different vBIOS?
I recommend using the stock vBIOS with this mod, you do not need to allow more power after it and that way you get all the timing information Asus designed the card for (not that this is likely to be important based on user reports).

Quote: Originally Posted by dante`afk View Post
welll< I don't have a multimeter, can this not be answered without?

FE card
If it is an FE card then you can look at my photos in the OP, I have highlighted the two resistors to add with red squares. You are correct, do not add one to the lower shunt on the front.
03-14-2019 08:53 AM
Renegade5399
Quote: Originally Posted by LCRava View Post
Do you guys recommend using the stock Strix 2080 Ti vBIOS with the Shunt Mod or a different vBIOS?

Thx for the help!
Stock or XOC on water. The Strix card is what XOC was made for AFAIK.

Quote: Originally Posted by dante`afk View Post
welll< I don't have a multimeter, can this not be answered without?

FE card
See attached pictures.
03-14-2019 05:15 AM
dante`afk welll< I don't have a multimeter, can this not be answered without?

FE card
03-11-2019 07:25 AM
JackCY Just take a multimeter or look at the PCB it should be quite clear what shunt is for what connector.

On Turing it seems NV has lowered the "limit" and only 3mOhm works, not 2.5mOhm anymore. 5+8=3.08 or you can buy a 3 if you want to desolder the original 5.
03-11-2019 07:02 AM
dante`afk I'm getting my heatkiller this week and since I'll disassembling my current block, I'll also perform the shunt mod, I bought the 8ohms which OP @Asmodian posted and solder them on top of the existing ones.

just to clarify; I'll do that on the bottom right shunt and on the top right on the back, right? Not on the once near the PCI-E connectors?
03-11-2019 03:37 AM
LCRava Do you guys recommend using the stock Strix 2080 Ti vBIOS with the Shunt Mod or a different vBIOS?

Thx for the help!
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off