Overclock.net - An Overclocking Community - Reply to Topic

Thread: [Official] NVIDIA GTX 1080 Ti Owner's Club Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-21-2019 12:44 AM
kithylin
Quote: Originally Posted by 8051 View Post
Do you have a thread where I can follow the progress on this build kithylin? DDR3 is what you mean right? DDR3 to 3000Mhz. or 3200Mhz.! Would that be faster than DDR4 at those speeds? I only ask because I thought DDR3 had lower latencies than DDR4.
I meant DDR3 yes, typo. Supposedly this kit I have (from some results I've found on hwbot.org with the same kit) should be capable of 3200 mhz @ 14-14-14. I don't know but I don't think there is a lot of DDR4 that can do that. I had a thread.. but no one noticed it. I'll PM you about it. We're veering off topic here.
10-21-2019 12:32 AM
8051
Quote: Originally Posted by kithylin View Post
I'm surprised anyone even found my thread on that. Yes I'm running old parts OC'd out the butt daily-driver. I have full intentions of setting up a 3770K and try to clock it to 5.5 Ghz minimum for daily-driver, bare chip delidded direct to waterblock with big loop while I wait around for Ryzen 4000 series threadripper to release in a few years. I have a set of ram I'm looking to pair with it to stretch it's legs later too. Corsair Vengeance 32GB (4x8GB) DDR2-2800 (XMP), and I'm hopeful to try to get it to 3000 - 3200 Mhz. I currently have it mated to an EK water cooled ram block that originally was mated to an old set of Corsair Dominator GT. I have the Vengeance set chemically bonded to the heatsinks for the water kit via resin so it's not just thermal pads.
Do you have a thread where I can follow the progress on this build kithylin? DDR3 is what you mean right? DDR3 to 3000Mhz. or 3200Mhz.! Would that be faster than DDR4 at those speeds? I only ask because I thought DDR3 had lower latencies than DDR4.
10-20-2019 02:38 PM
kithylin
Quote: Originally Posted by 8051 View Post
I'm slightly luckier than you I can get 2115 at 1.131V. I have to say I really admire your approach in building a rig -- massively overclocked last gen. parts.
I'm surprised anyone even found my thread on that. Yes I'm running old parts OC'd out the butt daily-driver. I have full intentions of setting up a 3770K and try to clock it to 5.5 Ghz minimum for daily-driver, bare chip delidded direct to waterblock with big loop while I wait around for Ryzen 4000 series threadripper to release in a few years. I have a set of ram I'm looking to pair with it to stretch it's legs later too. Corsair Vengeance 32GB (4x8GB) DDR2-2800 (XMP), and I'm hopeful to try to get it to 3000 - 3200 Mhz. I currently have it mated to an EK water cooled ram block that originally was mated to an old set of Corsair Dominator GT. I have the Vengeance set chemically bonded to the heatsinks for the water kit via resin so it's not just thermal pads.
10-20-2019 02:15 PM
8051
Quote: Originally Posted by kithylin View Post
My 1080 Ti needed 1.200v to do 2100 Mhz for example.
I'm slightly luckier than you I can get 2115 at 1.131V. I have to say I really admire your approach in building a rig -- massively overclocked last gen. parts.
10-18-2019 07:27 PM
VeritronX I ran across that a few years ago, I have the same card and I bought the nickel plexi fe block and nickel backplate for it.. they're still sitting in their boxes because the card runs so well as it was assembled with just a slight undervolt and a custom fan curve.

It sits at 1936-1950mhz core 993mv and +500 mem and almost never hits 70C or gets loud enough to be heard over 1500rpm 120mm vardars.
10-18-2019 05:12 PM
KedarWolf [quote=VeritronX;28163856]
Quote: Originally Posted by KedarWolf View Post

Keep in mind you need EK's geforce fe block not the 1080ti block because you need the cutout for the dvi ports that aren't installed on the reference model.
Yes, I already checked the compatibility list and know I need the FE black. TY though, it would help if someone never knew.

And it's the FE block Pheonix module that's on sale too!!
10-18-2019 04:39 PM
VeritronX [quote=KedarWolf;28158224]
Quote: Originally Posted by kithylin View Post
That's the card I have, exactly.

Here it is with the EK block on it:

I'm getting the acetal/nickel one. and with the Pheonix MLC QDC's GPU Module it's really cheap, waterblock and backplate, 121.98 USD on sale.
Keep in mind you need EK's geforce fe block not the 1080ti block because you need the cutout for the dvi ports that aren't installed on the reference model.
10-18-2019 12:27 PM
kithylin
Quote: Originally Posted by 8051 View Post
You have an excellent 1080Ti if you can get to 2100Mhz at such a low voltage. It's far better than mine.
My 1080 Ti needed 1.200v to do 2100 Mhz for example.
10-18-2019 05:00 AM
8051
Quote: Originally Posted by Streetdragon View Post
A little bit of 1080TI love
https://www.3dmark.com/spy/8708488

Best score so far. With 1.091V 2100Mhz stable(Still!) nice nice^^

Argh only place 4 with my rig^^
You have an excellent 1080Ti if you can get to 2100Mhz at such a low voltage. It's far better than mine.
10-14-2019 02:59 PM
skupples i love my QDCs now that I've got it sorted. I placed an order for the largest series, & only focused on the correct mating... Turns out they're fudging huge, they barely fit in an STH10, for reference.

I'll have to completely redesign next time around to make it look proper.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off