Overclock.net - An Overclocking Community - Reply to Topic

Thread: [Official] Delidded Club / Guide Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-23-2020 04:42 PM
Sedril I finally did the delid to my 9900k and was happily surprised at the improvement...

I had been putting it off thinking it wasn't going to be huge, at least not like the 7700k's I did...

But it helped quite a bit... temps are way down and with the same voltage (1.35) I was able to go from 5ghz to 5.1ghz no issues... Stress tests great with lower temps by far than 5ghz was with the lid...

I used the rocket cool delid kit with direct die frame... and thermal grizzley conductonaut

Now I'll see how high I can go keeping within comfortable voltages for a 24/7 build...

Good stuff!
07-22-2020 02:26 PM
Peter Watson
Quote: Originally Posted by eminded1 View Post
i delided and used the rockitcool 10th gen Copper IHS on my i7 10700k and temps are 8-10c less than stock.. not bad... i used Cool Labratory Liquid Pro inbetween the IHS and Silicon, temps used to get to low 90,s now there in the high 70s, low 80s when doign the same p95 smallfft AVX load tests at 5GHZ all Core 1.35 Vcore with LVL6 LLC. Not bad i bet i could get 5.1 or 5.2 stable with all core now becuase of the copper IHS i put on. i bet once somone releises a Direct Die Kit for the 10th Gen Intel Processors ill be able to get another 5-7c going direct die to cooler. (h150i)
Yep direct die for me at 5.0ghz all core avx 0, 1.36v prime95, I hit around 62c on my custom loop. I would imagine yours would be very similar with good cooling..
07-20-2020 11:13 AM
mouacyk
Quote: Originally Posted by ViTosS View Post
A question about this, my friend's notebook has an i5 5200U and I'm considering put liquid metal on it, but there are two very close dies, would it be a problem if the liquid metal touchs each other (making these two dies contact)?
It will be fine. There is no electrical conductance through the die substrate. What you don't want to get liquid metal on are those exposed pins on the surface -- use liquid electrical tape to seal them off.
07-19-2020 01:28 PM
ViTosS A question about this, my friend's notebook has an i5 5200U and I'm considering put liquid metal on it, but there are two very close dies, would it be a problem if the liquid metal touchs each other (making these two dies contact)?
07-16-2020 09:21 PM
TwilightRavens Dunno if GPU's count but I just delidded my GTX 285 tonight with a razorblade and a heatgun
07-15-2020 07:00 AM
eminded1 i delided and used the rockitcool 10th gen Copper IHS on my i7 10700k and temps are 8-10c less than stock.. not bad... i used Cool Labratory Liquid Pro inbetween the IHS and Silicon, temps used to get to low 90,s now there in the high 70s, low 80s when doign the same p95 smallfft AVX load tests at 5GHZ all Core 1.35 Vcore with LVL6 LLC. Not bad i bet i could get 5.1 or 5.2 stable with all core now becuase of the copper IHS i put on. i bet once somone releises a Direct Die Kit for the 10th Gen Intel Processors ill be able to get another 5-7c going direct die to cooler. (h150i)
07-09-2020 05:51 AM
Peter Watson
Quote: Originally Posted by zlatanselvic View Post
Hey Guys,

I had a misstep delidding a 10700k today for my office rig. The tool pushed down when pressing the IHS off. Never seen that happen before. (I did a 10900k a few weeks ago, and 9900k for a buddy over the weekend without issue.) Motherboard won't get here until tomorrow.


What do you think? Is it toast? I covered the gash with some super glue. I wish I knew how these PCB's were printed to determine if the traces are indeed on the surface or go down further.

From what I'm reading, if you're below the copper; you've gone too far. I think I am only through the soldermask and silkscreen layer.
I never knew about the copper layer on the die until I've just seen it here, I just kept sanding until the layer was completely gone as I thought the die was not perfectly flat, cpu seems to be working perfect though and temps are great now, hope your cpu is not dead..

Edit: Did the cpu work or was it toast?
07-09-2020 01:06 AM
mattxx88
Quote: Originally Posted by zlatanselvic View Post
Sent them an email with screenshots. Will know more tomorrow when I assemble the rig and see if it works.
any news about? it works?
07-06-2020 11:37 PM
zlatanselvic
Quote: Originally Posted by Falkentyne View Post
Contact Rockitcool. They will warranty any product damaged by their delid kit, however I do NOT know for sure if it covers 10th gen.

Jacky, the ingredients are pretty cheap for how much you get.
I got 100g for $30 but its more expensive now.

https://www.amazon.com/Gallium-Scien...dp/B07L2XYF66/ (x2)
Indium (x2=40g): https://www.ebay.com/itm/Indium-Meta...e/223117510144
Tin: https://www.ebay.com/itm/Tin-Metal-E...e/372414604222

Then a crucible to smelt it in the oven and some syringes and tips.
That's enough to make 150 grams. Not too expensive considering how much money you guys pay for other stuff.
And you can always sell small amounts leftover to someone else too.
Sent them an email with screenshots. Will know more tomorrow when I assemble the rig and see if it works.
07-06-2020 07:55 PM
Falkentyne
Quote: Originally Posted by zlatanselvic View Post
Hey Guys,

I had a misstep delidding a 10700k today for my office rig. The tool pushed down when pressing the IHS off. Never seen that happen before. (I did a 10900k a few weeks ago, and 9900k for a buddy over the weekend without issue.) Motherboard won't get here until tomorrow.


What do you think? Is it toast? I covered the gash with some super glue. I wish I knew how these PCB's were printed to determine if the traces are indeed on the surface or go down further.

From what I'm reading, if you're below the copper; you've gone too far. I think I am only through the soldermask and silkscreen layer.
Quote: Originally Posted by JackCY View Post
@zlatanselvic :
If you've cut any of the traces, it's RIP.
If you get liquid metal on those traces, it's RIP.

The slider in the delid tool should have 2 large rails on both sides, there should be no way it can dig down, I guess what happened was that the IHS while being pushed tipped down and dug into the PCB. This is why the better delid tools rotate the IHS instead or the expensive pusher delid tools are more precise and provide top support for the IHS so it can't angle.

Even if you only smashed some traces together, it's RIP.

As far as I know the PCBs are multi layer, there are tons of connections to make.


https://www.anandtech.com/show/9505/...ckage-analysis


@Falkentyne : Yes the liquid metal should be that simple. The thing is getting the materials and at a cost where it makes sense over buying the ready to use finished product.
Contact Rockitcool. They will warranty any product damaged by their delid kit, however I do NOT know for sure if it covers 10th gen.

Jacky, the ingredients are pretty cheap for how much you get.
I got 100g for $30 but its more expensive now.

https://www.amazon.com/Gallium-Scien...dp/B07L2XYF66/ (x2)
Indium (x2=40g): https://www.ebay.com/itm/Indium-Meta...e/223117510144
Tin: https://www.ebay.com/itm/Tin-Metal-E...e/372414604222

Then a crucible to smelt it in the oven and some syringes and tips.
That's enough to make 150 grams. Not too expensive considering how much money you guys pay for other stuff.
And you can always sell small amounts leftover to someone else too.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off