Overclock.net - An Overclocking Community - Reply to Topic
Thread: *Official* Intel DDR4 24/7 Memory Stability Thread Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-11-2020 09:43 PM
munternet
Quote: Originally Posted by JMTH View Post
Most all heat spreaders are removable, it's just a pain to do so hehe. Typically they use a really sticky tim. Just use a heat gun to heat the plates and soften up the adhesive until you can pull them from the dram. You should be able to use your hands but you might want to use some rags so you don't burn your fingers.
Yeah, cheers
I was wondering about the size as I tried to water cool some Corsair Dominator Platinums once but the PCBs wouldn't fit but I watched a youtube and it should be good
07-11-2020 08:45 PM
JMTH
Quote: Originally Posted by munternet View Post
Can anybody tell me if the heat spreaders on these F4-3600C16D-32GTZR G.Skill RGB sticks is removable and whether the EK Monarch plates will fit?
Cheers
Edit: There is a $65 price difference with these sticks F4-3200C14D-32GTZR. Is it worth paying for the 3600cl16s ?
Most all heat spreaders are removable, it's just a pain to do so hehe. Typically they use a really sticky tim. Just use a heat gun to heat the plates and soften up the adhesive until you can pull them from the dram. You should be able to use your hands but you might want to use some rags so you don't burn your fingers.
07-11-2020 07:20 PM
metalspider decided to put a 120mm fan for now and try stuff at 1.5v.
for some reason i seem to get slightly better scores in aida with tras at 40 then at 38.a few more MB bandwidth and 0.1-0.2ns faster too.
07-11-2020 07:03 PM
munternet
Quote: Originally Posted by ThrashZone View Post
Hi,
Less voltage needed for 3600 obviously and good for 4200..
3200 well depends on how much juice you want to pump into them but same goes for 3600c16
Thanks for that, good points
Just looking on youtube and the EK Monarch plates do indeed fit the RGB version
07-11-2020 05:56 PM
ThrashZone
Quote: Originally Posted by munternet View Post
Can anybody tell me if the heat spreaders on these F4-3600C16D-32GTZR G.Skill RGB sticks is removable and whether the EK Monarch plates will fit?
Cheers
Edit: There is a $65 price difference with these sticks F4-3200C14D-32GTZR. Is it worth paying for the 3600cl16s ?
Hi,
Less voltage needed for 3600 obviously and good for 4200..
3200 well depends on how much juice you want to pump into them but same goes for 3600c16
07-11-2020 05:40 PM
munternet Can anybody tell me if the heat spreaders on these F4-3600C16D-32GTZR G.Skill RGB sticks is removable and whether the EK Monarch plates will fit?
Cheers
Edit: There is a $65 price difference with these sticks F4-3200C14D-32GTZR. Is it worth paying for the 3600cl16s ?
07-11-2020 03:31 PM
munternet
Quote: Originally Posted by mouacyk View Post
KIT: 3600C15 2x8GB
Finally got around to testing beyond my stable 4000 profile. 4133 seems to be about as far as my 9900K will go. 4266 17-18-18
occasionally boots, but higher will not even with up to 1.6v on ram and 1.4v on io/sa.
Seems like a reasonable overclock

IF you want any suggestions to try....
The limitation might be the motherboard being a Z370 rated at 4133+?
Can you lower RTLs on that BIOS? 60/61/7/7/21/21 or 60/60/7/6/21/21 or 59/60/6/6/21/21. tCWL can be raised a little if it means being able to lower RTLs
tWR tested best overall performance at 16 even though it could go as low as 6 on my setup as was recommended by Gen.
Keeping the primaries in line seems to be best for B-Die. 17-17-17-37 seems to tune better for performance than 16-17-17-36 with my kit.
Lowering tRFC below 360 also does nothing for me in terms of Aida performance.
If I'm telling you how to suck eggs just ignore me
07-11-2020 02:06 PM
Nizzen
Quote: Originally Posted by ThrashZone View Post
Hi,
Has memory oc'ing past a tuned 4k mhz made any real difference in benchmark scores ?
I've seen no benefits of going over 4k mhz just easier to corrupt the os
Higher min fps in Battlefield V multiplayer. Only game I play. Rest of the games is only for benchmarking LOL
07-11-2020 11:35 AM
OLDFATSHEEP
Quote: Originally Posted by ogider View Post
43c but I have 80mm fan from NoiseBlocker mounted above dimms. 1200rpm. Was 26c outside case during tests.
Good enough

I am using Dimm.2 so most Dimm fan mounts don't work well. Tried to put an NF-A12 @2000 rpm near the sticks but this interrupted the front radiator airflow.
07-11-2020 11:34 AM
metalspider
Quote: Originally Posted by mouacyk View Post
KIT: 3600C15 2x8GB
Finally got around to testing beyond my stable 4000 profile. 4133 seems to be about as far as my 9900K will go. 4266 17-18-18
occassionally boots, but higher will not even with up to 1.6v on ram and 1.4v on io/sa.

could be a dimm pcb issue.if you have A0 it pretty much tops out at 4133mhz.
but 3600c15 is the best low latency b-die afaik.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off