Overclock.net - An Overclocking Community - Reply to Topic

Thread: [Official] Asus CrossHair IV Formula/Extreme Club Reply to Thread
Title:
Message:

Register Now

In order to be able to post messages on the Overclock.net - An Overclocking Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-13-2018 03:22 AM
bbowseroctacore 3017 beta version for am3+ cpu's only is what u need - not to be used with am3 cpu's
10-12-2018 04:42 PM
ziire Hi!

I have the Crosshair IV Formula and i cant get it work with the Fx-8350
My bios version is 3029 and i have tried 3027. What im doing wrong?
08-09-2018 01:01 PM
dead4ngel Hi there. Recently bought my pc. Heres the specs:


Operating System
Windows 10 Pro 64-bit
CPU
AMD Phenom II X6 1090T
Thuban 45nm Technology
RAM
16.0GB Dual-Channel DDR3 @ 621MHz (9-9-9-24)
Motherboard
ASUSTeK Computer INC. Crosshair IV Formula (AM3) 32 °C
Graphics
HZ281H ([email protected])
4095MB NVIDIA GeForce GTX 970 (Gigabyte) 34 °C
Storage
1863GB TOSHIBA DT01ACA200 ATA Device (SATA ) 32 °C
465GB Samsung SSD 860 EVO 500GB ATA Device (SATA (SSD)) 32 °C
1863GB Western Digital WDC WD20EARX-00PASB0 ATA Device (SATA ) 28 °C
Optical Drives
HL-DT-ST DVDRAM GH22NS50 ATA Device
HL-DT-ST DVDRAM GH22LS50 ATA Device
i hbave a amd fx 8350 cpu on its way. I just want to know what steps to make it run right once it comes. Whcih bios is better to use 3027 or 3029? I have tried searching for modded ones with no luck. In my bios can anyone guide me on what to enable and disable.



Now from the few bits i have gathered this is what i think i need to do. Flash one of those bios's whilst on the current cpu. Then change voltage i think to 1.3 then install new cpu apply thermal paste etc and boot up right. I have tried looking for a full guide but no luck. cooling wise i havent got an issue. If anyone can guide me id appreciate it thanks.
10-23-2017 01:50 AM
phoenix1975 Motherboard: Asus Crosshair iv formula
Bios: 2101 mod


1. Updated AMD RAID ROM To v3.3.1540.19
2. Updated JMicron 363 ROM to v1.08.01
3. updated AMD AHCI ROM To v3.3.2.0
4. Add slic 2.1

https://www110.zippyshare.com/v/LK1rxNfW/file.html
04-24-2017 04:25 PM
Ceadderman It's because of the updated BIOS lacking the safety features originally intended for the Phenoms. I fully suspect that the NB heatsink also needs to be addressed to bring the Temps down. Lack of optimal contact is allowing the NB chip to run over the maximum temp range. You can check that temp setting in BIOS, it should be no higher than 65c. If it is I think you can set the temp max to 65c. But since I never had to I am not entirely certain of that. mellowsmiley.gif

~Ceadder smil3dbd4e4c2e742.gif
04-24-2017 05:27 AM
dexis Thank you @Ceadderman. The fact i can't understand is why, with my Phenom II 965, all were working fine. The overheating problem appeared on GPU after the FX-6300 upgrade.

PD. Last time that Windows 10 booted, GPU-Z was showing 103ºC on GPU @ ~1.20v

PD2. CPU/NB ran @ 70ºC easily while I was in BIOS. The heating problem with the GPU is happening while you stay in BIOS too.
04-23-2017 10:13 PM
Ceadderman Stock NB/SB heatsink? Likely need to do the standoff modification to close the gap between chipset and heatsink. CIVFormula was shipped with incorrect NB standoffs. Think of the issue like an Intel chip needing a deli to keep the Temps under control. Only on a mb. I'm actually quite shocked that your board is not shutting down when your NB hits 65c, the way it should be. But that could be directly due to the updated BIOS lacking the proper safety measures. I would contact ASUS and have them look over that BIOS and check to see where that issue occured. NB chips with proper cooling should go no further than 60c. I changed out with an EK chips block and mine goes no higher than 55c.

So if you're running stock cooling I would do the standoff mod. Change the SB standoffs to the NB an keep an eye on temps. If it lowers sand down the female side to match the ones swapped to NB. Reset the standoffs and mod is done. thumb.gif

~Ceadder smil3dbd4e4c2e742.gif
04-23-2017 09:18 PM
dexis I've just upgraded my cpu. Phenom II 965 to FX-6300 (BIOS v.3029).

Well, after this upgrade my GPU is overheating and losing the signal video after a few minutes. It's happening during BIOS config and after/during Windows 10 boot. Fans are at 100%. (ASUS EAH5870 1GB).

I'm not sure what parameter of BIOS is causing this. I have tried it with default BIOS cfg too.

PD. My NB temp is over 75ºC in idle.
04-06-2017 09:31 PM
Ceadderman Two 8gb sticks work well. I have a pair of 1600 Dominator I ran in.mine without much issue. Though I did have to activate the Go!Button to get the board to POST because 8gb sticks did not exist prior to the CIVFormula QVL iirc. thumb.gif

You won't be able to run more as the board will be maxed out for memory. tongue.gif

~Ceadder smil3dbd4e4c2e742.gif
04-06-2017 10:16 AM
Wbroach23 Hey will the crosshair IV run two 8gb sticks of RAM or do I need to run 4 4gb sticks? It's my old build now but I need to get it a little better so my cousin can use it till we build him a newer one.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off