Overclock.net - An Overclocking Community

Overclock.net - An Overclocking Community (https://www.overclock.net/forum/)
-   Water Cooling (https://www.overclock.net/forum/61-water-cooling/)
-   -   Old Crosair h100i. Unusally high temps (https://www.overclock.net/forum/61-water-cooling/1734228-old-crosair-h100i-unusally-high-temps.html)

skupples 10-06-2019 07:17 AM

7 years is pretty damn good, we got 4-5 out of our h80/100s.

failure for us were temps drastically higher than originals. my i5 was delidded with CLP(cuz time is a thing) so my IHS temps never changed.,

bhsmurfy 10-10-2019 12:52 PM

Quote:

Originally Posted by skupples (Post 28150466)
7 years is pretty damn good, we got 4-5 out of our h80/100s.

failure for us were temps drastically higher than originals. my i5 was delidded with CLP(cuz time is a thing) so my IHS temps never changed.,

Oh yeah its frankinstiend now. Thats for sure.

I cut the hoses from the rad added a submerged pump and i have aa reso outside my window. (day temps of 20c night temps of -10c) Its -3c outside right now

I've gutted the pump and have flown water thru it without the rubber gromet that spreads water and with. Cant get below 95c r15 @ 4.4Ghz :( This thing used to daily rock out 65c @ 4.8Ghz

I thru a Air cooler on it also and nothing. So Im gonna post on FB today if anyone has a table vice I can come use and delid and I will re-apply TIM.

Will see if it helps. Also notice one of the pins on the mobo is janky. probably my cause of WHEA UNCONTROLLABLE ERROR and HARDWARE CHECKS BSOD

To be fair. I think the h100i was never the problem. The coolant was yellow like it should off been no micro-bacteria or anythinig. Never got weird noises from it or anything.

The Pook 10-10-2019 12:54 PM

a bent pin is likely not the cause of your BSOD. a large majority of pins are reserved and do nothing or are just redundant grounds.

bhsmurfy 10-10-2019 01:12 PM

Quote:

Originally Posted by The Pook (Post 28154968)
a bent pin is likely not the cause of your BSOD. a large majority of pins are reserved and do nothing or are just redundant grounds.

Well thats good to know.

bhsmurfy 10-11-2019 03:36 PM

Ok, update time. I found the culprit. I knew a 30c difference between cores should of been a red flag.
https://i.imgur.com/vqJ8DmR.jpg

So here is what im thinking. One night while on my OC config 4.7g-4.8g my pump got clogged and let the CPU bake at about 104c all night(i know i normally turn thermal protection on when afk) and it dried out the superb Intel TIM job.

Took her to the local library pop'd her open with a table vice applied some new as5(all i have without waiting a week on shipping) and now my cores are within 1c at each other with a 37c Idle @ 4.6g 1.32v while my water temp is 13c.

At night water temp is normally -5c to 0c.

Man im so ******* stoked this thing will last until November now.

Was seriously giving me bad luck for the past week.

chas1723 10-12-2019 05:12 AM

Your water temp will not be below ambient. Something is not reading right if that is the numbers you are being shown. Also AS5 is junk for delis. Your temps will go up substantially in a few weeks due to paste pump out effect.

Sent from my SM-N950U using Tapatalk

Hydroplane 10-12-2019 05:51 AM

Quote:

Originally Posted by chas1723 (Post 28156892)
Your water temp will not be below ambient. Something is not reading right if that is the numbers you are being shown. Also AS5 is junk for delis. Your temps will go up substantially in a few weeks due to paste pump out effect.

Sent from my SM-N950U using Tapatalk

I think he has the radiator outdoors. OP, just watch the dew point, don't want your motherboard to start getting sweaty lol

chas1723 10-12-2019 11:04 AM

Did he add tube length? My h100i did not have enough tube to get it out of my case much less outside.

Sent from my SM-N950U using Tapatalk

bhsmurfy 10-12-2019 11:23 AM

Quote:

Originally Posted by Hydroplane (Post 28156916)
I think he has the radiator outdoors. OP, just watch the dew point, don't want your motherboard to start getting sweaty lol

correct.
I keep an eye on RH/DP

bhsmurfy 10-12-2019 02:37 PM

Quote:

Originally Posted by chas1723 (Post 28157152)
Did he add tube length? My h100i did not have enough tube to get it out of my case much less outside.

Sent from my SM-N950U using Tapatalk

Yes. I have cut the rad out and removed the rubber gourmet from inside the block that focuses water into fins(the submersed pump i use is too strong for the gromet to be in there and im not finding any negative from it *yet*

I have a res outside my window where i have a couple gallons of water/antifreeze/organic hydrogen peroxide flowing. The rez sits in like a pile of snow outside my window. My only problem now is I cant get pass 4.9stable. Ive gotten a couple post at 5Ghz but get hardware checks/clock watch dogs/kernel exceptions etc BSOD when logging into windows. :( Think its this VRM on the ASRock z97 f4tality killer was a cheap mobo at the time and surprised it has lasted this long with all the abuse and shorts and forgetting to ground my self and bending capacitors i have done to it.

I have a liquid metal in the mail.

Im waiting for a waterblock for my 2080 ti also. and a actual ek block for my cpu instead of the gutted h100i.
672 r15. Not bad for a i5 4690k considering stock score is 430-450 i think.


All times are GMT -7. The time now is 03:57 AM.

Powered by vBulletin® Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.

User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.

vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.