Overclock.net banner

1 - 16 of 16 Posts

·
Banned
Joined
·
550 Posts
Discussion Starter #1
i wanna reach 2.5 with my current hardware..ive reached it befor but i wanst stable guessing because of my ram but tht was on a 1:1 ratio... i adjusted the ratio but look at my timings, can any one tell me how to fine tune then so i could be stabvle at 2.5?

im at 222X11 and its tsill not stable(errors on prime95) my ram speed is at 175 mhz...help!
 

·
Premium Member
Joined
·
9,589 Posts
Try changing your cas latency to 3 (instead of 2.5)

And drop your HTT (LDT) multiplier to 3.

Are you running a SATA drive?

How are your temps?

1.5 seems a little low, but should be ok for now (I'm so used to DTR's)

Whats your Vldt (chipset/mobo voltage?)
 

·
Banned
Joined
·
550 Posts
Discussion Starter #6
Quote:


Originally Posted by Xavier1421

Try changing your cas latency to 3 (instead of 2.5)

And drop your HTT (LDT) multiplier to 3.

Are you running a SATA drive?

How are your temps?

1.5 seems a little low, but should be ok for now (I'm so used to DTR's)

Whats your Vldt (chipset/mobo voltage?)

k my temps are ok(35c and at load 48-49c) i dont no how to change my htt multi, im not runnin an sata.my chipset and mobo voltages r stock.what do u suggest doin?
 

·
Premium Member
Joined
·
9,589 Posts
Quote:


Originally Posted by illusion34

k my temps are ok(35c and at load 48-49c) i dont no how to change my htt multi, im not runnin an sata.my chipset and mobo voltages r stock.what do u suggest doin?

Go into your bios, there will be a place to change those settings, look around


If you do like I said, you should be a little more stable to push forward more.

Raise both your ram and mobo voltage up 1 increment.

Watch your cpu temps...49 is gettin close to upgrading the cooling
 

·
Banned
Joined
·
550 Posts
Discussion Starter #8
Quote:


Originally Posted by Xavier1421

Go into your bios, there will be a place to change those settings, look around


If you do like I said, you should be a little more stable to push forward more.

Raise both your ram and mobo voltage up 1 increment.

Watch your cpu temps...49 is gettin close to upgrading the cooling

k ill try brb
 

·
Banned
Joined
·
550 Posts
Discussion Starter #9
Quote:


Originally Posted by illusion34

k ill try brb

ok its stble now but im not gettin good temps(load 50c) can u tell me if all my stuff is alright if i send u aa screenie??? and im gettin worse pi scores den b4???
 

·
Premium Member
Joined
·
9,589 Posts
lower pi because the ram isnt running 1:1

Temps because you've picked up a few settings...50 degc load is still doable..but you'll want lower if you want more speed

What is your system running at now? screenies?
 

·
Banned
Joined
·
550 Posts
Discussion Starter #12
srry man i put it back to stock..it was runnin at 22X11 fsb the htt was 3, my voltage was 1.5 with a command of 110%, and i rasied everything u sed to 1 increment.
 

·
Premium Member
Joined
·
9,589 Posts
Quote:

Originally Posted by illusion34
dam i need new cooling...will the xp-120 hold up?
extremely well. put an xp120 and a medium or high speed panaflo on it, you won't see over 40degC
 

·
Banned
Joined
·
550 Posts
Discussion Starter #15
Quote:

Originally Posted by Xavier1421
extremely well. put an xp120 and a medium or high speed panaflo on it, you won't see over 40degC
wow..den the ram.....wat bout the psu?
 
1 - 16 of 16 Posts
Top