Overclock.net banner

1 - 12 of 12 Posts

·
Data Recovery Engineer
Joined
·
20,225 Posts
Discussion Starter #1
Here is what I got so far:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: auto
CPU Clock Ratio ..........................:9
Fine CPU Clock Ratio.....................: 5
CPU Frequency ...........................: 3.8GHz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:400Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV<<<
PCI Express Clock Drive.................: 900mV<<<
CPU Clock Skew (ps)....................:0 <<<
MCH Clock Skew (ps)...................: 0<<<

DRAM Performance Controlhttp://forums.nonewbs.com/index.php
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.0D
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................3
tWTR..........................................3
tWR............................................6
tRFC...........................................54
tRTP...........................................3
Command Rate (CMD) ....................:0

Driving Strength Profiles
Driving Strength ............................ AUTO

Channel A
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.&#8230;&#8230;&#8230;... Manual
CPU
Load-Line Calibration: Enabled
CPU Vcore&#8230;.&#8230;&#8230;&#8230;.........................:1.4
CPU Termination&#8230;..... 1.200V*.......: 1.28
CPU PLL&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;....1.500V*.......: 1.5

CPU Referen.&#8230;&#8230;&#8230;&#8230;....0.755V*.......: 0.760<<< .64% Of Vtt (Termination above) Auto ?

MCH/ICH
MCH Core&#8230;&#8230;&#8230;&#8230;&#8230;.....1.100V...........: 1.3
MCH Reference&#8230;.&#8230;&#8230;.0.800V...........; <<< Leave (current is set at 0.760v Auto)
MCH/DRAM Ref.&#8230;......0.900V...........: <<< auto
ICH I/O&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;.....1.550V............: <<< 1.5 auto
ICH Core&#8230;&#8230;&#8230;&#8230;...&#8230;&#8230;1.100V............: <<< auto

DRAM
DRAM Voltage &#8230;&#8230;....1.800V............: 2.2v (Ram doesn't like running at stock for some reason)
DRAM Termination .&#8230;0.900V............: <<< Auto
Channel A Reference 0.900V............: <<< Auto
Channel B Reference 0.900V............: <<< Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

Update:

Finally got a 3.8 stable in ITB by my temps were really high (76C!!!!):

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: auto
CPU Clock Ratio ..........................:9
Fine CPU Clock Ratio.....................: 5
CPU Frequency ...........................: 3.8GHz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:400Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV<<<
PCI Express Clock Drive.................: 900mV<<<
CPU Clock Skew (ps)....................:0 <<<
MCH Clock Skew (ps)...................: 0<<<

DRAM Performance Controlhttp://forums.nonewbs.com/index.php
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.0D
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................3
tWTR..........................................3
tWR............................................6
tRFC...........................................54
tRTP...........................................3
Command Rate (CMD) ....................:0

Driving Strength Profiles
Driving Strength ............................ AUTO

Channel A
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.&#8230;&#8230;&#8230;... Manual
CPU
Load-Line Calibration: Enabled
CPU Vcore&#8230;.&#8230;&#8230;&#8230;.........................:1.4
CPU Termination&#8230;..... 1.200V*.......: 1.28
CPU PLL&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;....1.500V*.......: 1.5

CPU Referen.&#8230;&#8230;&#8230;&#8230;....0.755V*.......: 0.760<<< .64% Of Vtt (Termination above) Auto ?

MCH/ICH
MCH Core&#8230;&#8230;&#8230;&#8230;&#8230;.....1.100V...........: 1.3
MCH Reference&#8230;.&#8230;&#8230;.0.800V...........; <<< Leave (current is set at 0.760v Auto)
MCH/DRAM Ref.&#8230;......0.900V...........: <<< auto
ICH I/O&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;.....1.550V............: <<< 1.5 auto
ICH Core&#8230;&#8230;&#8230;&#8230;...&#8230;&#8230;1.100V............: <<< auto

DRAM
DRAM Voltage &#8230;&#8230;....1.800V............: 2.2v (Ram doesn't like running at stock for some reason)
DRAM Termination .&#8230;0.900V............: <<< Auto
Channel A Reference 0.900V............: <<< Auto
Channel B Reference 0.900V............: <<< Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
 

·
Premium Member
Joined
·
2,664 Posts
Isnt 1.4vcore a bit much for 45nm? I thought that 1.36 was the max. What is the vcore reading in windows? Does it drop to a safe level?

I would have to guess that the chip is close to its max, thats good for an E7300. What kinda temps you running?
 

·
Data Recovery Engineer
Joined
·
20,225 Posts
Discussion Starter #3
I am running 72C but I was just trying to get it to there just to say I did. Right now I am running (all the time) what is in my sig. And no it doesn't drop into the safe zone... The max vcore for a 45nm chip is 1.6v. The 1.3625 is just to scare you from going higher. But it isn't like I am running it full time like that.
 

·
Data Recovery Engineer
Joined
·
20,225 Posts
Discussion Starter #4
Update:

FINALLY!! I got a stable 3.8 but temps got to 76C!!!

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: auto
CPU Clock Ratio ..........................:9
Fine CPU Clock Ratio.....................: 5
CPU Frequency ...........................: 3.8GHz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:400Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV<<<
PCI Express Clock Drive.................: 900mV<<<
CPU Clock Skew (ps)....................:0 <<<
MCH Clock Skew (ps)...................: 0<<<

DRAM Performance Controlhttp://forums.nonewbs.com/index.php
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.0D
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................3
tWTR..........................................3
tWR............................................6
tRFC...........................................54
tRTP...........................................3
Command Rate (CMD) ....................:0

Driving Strength Profiles
Driving Strength ............................ AUTO

Channel A
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.&#8230;&#8230;&#8230;... Manual
CPU
Load-Line Calibration: Enabled
CPU Vcore&#8230;.&#8230;&#8230;&#8230;.........................:1.45
CPU Termination&#8230;..... 1.200V*.......: 1.32
CPU PLL&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;....1.500V*.......: 1.5

CPU Referen.&#8230;&#8230;&#8230;&#8230;....0.755V*.......: 0.760<<< .64% Of Vtt (Termination above) Auto ?

MCH/ICH
MCH Core&#8230;&#8230;&#8230;&#8230;&#8230;.....1.100V...........: 1.3
MCH Reference&#8230;.&#8230;&#8230;.0.800V...........; <<< Leave (current is set at 0.760v Auto)
MCH/DRAM Ref.&#8230;......0.900V...........: <<< auto
ICH I/O&#8230;&#8230;&#8230;&#8230;&#8230;&#8230;.....1.550V............: <<< 1.5 auto
ICH Core&#8230;&#8230;&#8230;&#8230;...&#8230;&#8230;1.100V............: <<< auto

DRAM
DRAM Voltage &#8230;&#8230;....1.800V............: 2.2v (Ram doesn't like running at stock for some reason)
DRAM Termination .&#8230;0.900V............: <<< Auto
Channel A Reference 0.900V............: <<< Auto
Channel B Reference 0.900V............: <<< Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
 

·
Data Recovery Engineer
Joined
·
20,225 Posts
Discussion Starter #7
This is OC at 3.8 with 1.45 vcore. At 3.6 I get max 65C with ITB.
 

·
Data Recovery Engineer
Joined
·
20,225 Posts
Discussion Starter #9
I can't exactly lap a s1283....

The base of it looks like this:
 

·
Registered
Joined
·
695 Posts
You can actually, just don't take off a ton of metal. I don't know how flat the bottom of the heat pipes are, but if they aren't totally flat, you are loosing some efficiency that way. Also, you can still lap the CPU
 
1 - 12 of 12 Posts
Top