[dansi]

gigabtye updated their x570 v1.1 page, interesting all v1.1 can support ddr4 up to 5400, because of a :

Shielded Memory Routing
All memory routing is under the PCB inner layer shielded by a large ground layer to protect from external interference.

I wonder if this is marketing flub or real hardware addition to v1.1 boards?

https://www.gigabyte.com/us/Motherboard/X570-AORUS-XTREME-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-ULTRA-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-MASTER-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-PRO-rev-11#kf

 

[betam4x]

There are two versions of the trident z neo 3600. The one that ends with the GTNC is Hynix - I have those and run them at 3800 without issues. Destiny 2 plays perfect. There have been some reports of radeon GPU drivers causing drivers so hard to tell if the graphics card is causing you issues as well... I'm on a 2070 super.

Your RAM should be okay though... just try manually setting the Vdimm to 1.36V with your current settings and see how that goes?

There is also the GTZRC which is Hynix (just has RGB).

 

[dansi]

From the specifications page

Master v1.1

3rd Generation AMD Ryzen™ processors:
Support for DDR4 5200(O.C.) / 5000(O.C.) / 4866(O.C.) / 4600(O.C.)/ 4400(O.C.) / 4300(O.C.) / 4266(O.C.) / 4133(O.C.) / 4000(O.C.) / 3866(O.C.) / 3800(O.C.) / 3733(O.C.) / 3600(O.C.) / 3466(O.C.) / 3400(O.C.) / 3333(O.C.) / 3300(O.C.) / 3200 / 2933 / 2667 / 2400 / 2133 MHz memory modules
New Generation AMD Ryzen™ with Radeon™ Graphics processors:
Support for DDR4 5400(O.C.)/ 5200(O.C.) / 5000(O.C.) / 4866(O.C.) / 4600(O.C.)/ 4400(O.C.) / 4300(O.C.) / 4266(O.C.) / 4133(O.C.) / 4000(O.C.) / 3866(O.C.) / 3800(O.C.) / 3733(O.C.) / 3600(O.C.) / 3466(O.C.) / 3400(O.C.) / 3333(O.C.) / 3300(O.C.) / 3200 / 2933 / 2667 / 2400 / 2133 MHz memory modules
2nd Generation AMD Ryzen™ processors/ 2nd Generation AMD Ryzen™ with Radeon™ Vega Graphics processors / 1st Generation AMD Ryzen™ with Radeon™ Vega Graphics processors:
Support for DDR4 3600(O.C.) / 3466(O.C.) / 3400(O.C.) / 3333(O.C.) / 3300(O.C.) / 3200 / 2933 / 2667 / 2400 / 2133 MHz memory modules
4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity) of system memory
Dual channel memory architecture
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules*
* ECC mode supported by 3rd Gen AMD Ryzen™/ 2nd Gen AMD Ryzen™ and only PRO sku of 2nd Gen AMD Ryzen™ with Radeon™ Vega Graphics processors/ AMD Ryzen™ with Radeon™ Vega Graphics processors.
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
Support for Extreme Memory Profile (XMP) memory modules

Master v1.0

3rd Generation AMD Ryzen™ processors:
Support for DDR4 4400(O.C.) / 4300(O.C.) / 4266(O.C.) / 4133(O.C.) / 4000(O.C.) / 3866(O.C.) / 3800(O.C.) / 3733(O.C.) / 3600(O.C.) / 3466(O.C.) / 3400(O.C.) / 3333(O.C.) / 3300(O.C.) / 3200 / 2933 / 2667 / 2400 / 2133 MHz memory modules
2nd Generation AMD Ryzen™ processors/2nd Generation AMD Ryzen™ with Radeon™ Vega Graphics processors/AMD Ryzen™ with Radeon™ Vega Graphics processors:
Support for DDR4 3600(O.C.) / 3400(O.C.) / 3333(O.C.) / 3200(O.C.) / 2933 / 2667 / 2400 / 2133 MHz memory modules
4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity) of system memory
Dual channel memory architecture
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules*
* ECC mode supported by 3rd Gen AMD Ryzen™/ 2nd Gen AMD Ryzen™ and only PRO sku of 2nd Gen AMD Ryzen™ with Radeon™ Vega Graphics processors/ AMD Ryzen™ with Radeon™ Vega Graphics processors.
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
Support for Extreme Memory Profile (XMP) memory modules

 

[SacraficeMyGoat]

From the specifications page

Master v1.1



Master v1.0

Interesting. How can I tell if I have v1.0 or v1.1?

 

[dansi]

Interesting. How can I tell if I have v1.0 or v1.1?

quickest way is to see if you have 2 capacitors between your cpu socket and the ram slot, if yes, yours is v1.0

other changes include a thunderbolt header and some component switch in the top vrm section.

 

[ryouiki]

Board revision is printed on the very bottom left corner. I doubt there was much changes in that area of the board anyway, probably just different testing done on 1.1, my 1.1 board seems more fussy about memory then my 1.0 board.

 

[Spectre73]

gigabtye updated their x570 v1.1 page, interesting all v1.1 can support ddr4 up to 5400, because of a :

Shielded Memory Routing
All memory routing is under the PCB inner layer shielded by a large ground layer to protect from external interference.

I wonder if this is marketing flub or real hardware addition to v1.1 boards?

https://www.gigabyte.com/us/Motherboard/X570-AORUS-XTREME-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-ULTRA-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-MASTER-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-PRO-rev-11#kf

Can we be sure that this is only true for 1.1 and not 1.0? This should in practice not be relevant, but it could allow us lower frequencies, up to 3800 with better timings or easier stability.

 

[SacraficeMyGoat]

Board revision is printed on the very bottom left corner. I doubt there was much changes in that area of the board anyway, probably just different testing done on 1.1, my 1.1 board seems more fussy about memory then my 1.0 board.

Thanks. Mine is 1.1 as well.

 

[RaXelliX]

F20A showed up for my xtreme as well. Guessing this is the bios that includes the newer agesa? I'm gonna hold off for now until I see a handful of reports to see how well its working for everyone.

Update AMD AGESA ComboV2 1.0.0.2 for 3rd Gen AMD Ryzen XT series processors and New Gen AMD Ryzen with Radeon Graphics processors support

Only +0.08MB added to BIOS filesize. Not bad imho.

 

[Illined]

Installed the Combo AGESA BIOS for the Aorus X570 Master (F20A). Changes include minor graphical updates (for example the yes and no buttons to confirm settings no longer have a texture). The AMD CBS and AND Overclocking menus have been reorganised. XFR Enhancement seems to have vanished there




Apart from that I ran Memtest86 all night and it couldn't find any errors. I'm now excluding RAM from being a possible issue with my idle crashes.


Edit: screenshots of the F20A update. There is also mention of X590!

 

[R-Type!]

Installed the Combo AGESA BIOS for the Aorus X570 Master (F20A). Changes include minor graphical updates (for example the yes and no buttons to confirm settings no longer have a texture). The AMD CBS and AND Overclocking menus have been reorganised. XFR Enhancement seems to have vanished there




Apart from that I ran Memtest86 all night and it couldn't find any errors. I'm now excluding RAM from being a possible issue with my idle crashes.


Edit: screenshots of the F20A update. There is also mention of X590!

109 BCLK? Really?
My master can't go above 100.3 before SATA starts to act up.

 

[mrsteelx]

Installed the Combo AGESA BIOS for the Aorus X570 Master (F20A). Changes include minor graphical updates (for example the yes and no buttons to confirm settings no longer have a texture). The AMD CBS and AND Overclocking menus have been reorganised. XFR Enhancement seems to have vanished there




Apart from that I ran Memtest86 all night and it couldn't find any errors. I'm now excluding RAM from being a possible issue with my idle crashes.


Edit: screenshots of the F20A update. There is also mention of X590!

I like have the memory training options now.

 

[dansi]

Only +0.08MB added to BIOS filesize. Not bad imho.

holy! f20a bios extracted file size is a nice round 16mb!

we are doomed for those on gigabtye x570. :h34r-smi

 

[Cata79]

Stop spreading this crap. ALL bioses have the 16Mb size, moron.

 

[RaXelliX]

holy! f20a bios extracted file size is a nice round 16mb!

we are doomed for those on v1.0 x570. :h34r-smi

Truth is we don't know. I was just going by the ZIP file size.

 

[dansi]

Stop spreading this crap. ALL bioses have the 16Mb size, moron.

you are right, i apologise :h34r-smi

 

[Illined]

109 BCLK? Really?
My master can't go above 100.3 before SATA starts to act up.

No no, that is definitely wrong. I am running at stock with only XMP profile and PBO enabled. Never touched BCLK and just checked HWinfo and it is at 100Mhz. Checked again in the BIOS and it was reported at 100.41Mhz.

My system is nothing to be proud of since I am having constant crashes during idle... Even now with the changed Typical Current Idle. Changed now to Low Current Idle. It's very ****ty to have constant crashes and not know what is causing them. Almost ready to switch back to Intel.

 

[snabbledabble]

Does anyone know the bios update i stable? Looking to upgrade but would like to know if its better than 12g which is what i am currently on.

 

[superleeds27]

Are there any known improvements in Combo V2 for X570?

 

[pal]

gigabtye updated their x570 v1.1 page, interesting all v1.1 can support ddr4 up to 5400, because of a :



I wonder if this is marketing flub or real hardware addition to v1.1 boards?

https://www.gigabyte.com/us/Motherboard/X570-AORUS-XTREME-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-ULTRA-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-MASTER-rev-11#kf
https://www.gigabyte.com/us/Motherboard/X570-AORUS-PRO-rev-11#kf

rev 1.1 have thunderbolt pin header, 1.0 dont have it.