What is your VID and core voltage at now? Just bump up the voltage from what its at now (1.25 to less than 1.3 or so). You may also want to up your FSB voltage as well slighty. Make sure not to push it too far voltage wise and check your temps. Also do you have stock cooling?
[HELP]How to Overclock q6600+p5kpro
1 - 8 of 8 Posts
all of them are auto i only did the CPU Frequency to 301*9= 2.7Ghz and yes i'm on stock cooling il try to give it some volts just hope that i don't have to reset the bios again
![]()
Edit : i'm now testing whit 1.40 VCORE
http://valid.canardpc.com/show_oc.php?id=527988
But it's too hot whit stock cooling 65-68 degrees celsius
Edit : i'm now testing whit 1.40 VCORE
http://valid.canardpc.com/show_oc.php?id=527988
But it's too hot whit stock cooling 65-68 degrees celsius
ok il do that now and let you guys know and thanks for the support
![]()
EDIT: I Tryed 1.3 but my system wont start whit it so i'm back to 1.4 i think that i need about 1.38v il test later after il come back from work
i left my pc on whit prime for 8 hours on 1.40 VCore and no errors
http://img223.imageshack.us/my.php?image=proofc.jpg
EDIT: I Tryed 1.3 but my system wont start whit it so i'm back to 1.4 i think that i need about 1.38v il test later after il come back from work
i left my pc on whit prime for 8 hours on 1.40 VCore and no errors
http://img223.imageshack.us/my.php?image=proofc.jpg
Quote:
i have VID 1.3250 and 1.40 VCORE is this ok or i need to change someting here ? and sorry for duble posting
Edit: this is what i have in my bios so what do i need to change
Ai Overclock Tuner - Manual
CPU Ratio Setting [09.0]
FSB Strap to North Bridge [AUTO]
FSB Frequency [333]
PCI Frequency [100]
DRAM Frequency [AUTO]
DRAM Command Rate [2N]
DRAM Timing Control [AUTO]
DRAM Static Read Control [Disabled]
Transaction Booster [AUTO]
CPU Voltage [1.40000]
PCU PLL Voltage [AUTO]
FSB Termination Voltage [1.20]
DRAM Voltage [AUTO]
NB Voltage [AUTO]
SB Voltage [AUTO]
Clock Over Changing Voltage [AUTO]
Load-Line Calibration [AUTO]
CPU GTL Voltage Reference [AUTO]
NB GTL Voltage Reference [AUTO]
CPU Spread Spectrum [Disabled]
PCI Spread Spectrum [Disabled]
Originally Posted by waverider599  What is your VID and core voltage at now? Just bump up the voltage from what its at now (1.25 to less than 1.3 or so). You may also want to up your FSB voltage as well slighty. Make sure not to push it too far voltage wise and check your temps. Also do you have stock cooling? |
Edit: this is what i have in my bios so what do i need to change
Ai Overclock Tuner - Manual
CPU Ratio Setting [09.0]
FSB Strap to North Bridge [AUTO]
FSB Frequency [333]
PCI Frequency [100]
DRAM Frequency [AUTO]
DRAM Command Rate [2N]
DRAM Timing Control [AUTO]
DRAM Static Read Control [Disabled]
Transaction Booster [AUTO]
CPU Voltage [1.40000]
PCU PLL Voltage [AUTO]
FSB Termination Voltage [1.20]
DRAM Voltage [AUTO]
NB Voltage [AUTO]
SB Voltage [AUTO]
Clock Over Changing Voltage [AUTO]
Load-Line Calibration [AUTO]
CPU GTL Voltage Reference [AUTO]
NB GTL Voltage Reference [AUTO]
CPU Spread Spectrum [Disabled]
PCI Spread Spectrum [Disabled]
1 - 8 of 8 Posts
