Are all your ram timmings set? voltage set? Start by dropping your ram freq down a notch and start pushing the cpu freq up 5/10mhz at a time untill it bsod or won't boot then bump up the vcore one notch and boot. Test with prime95 or occt and keep an eye on those temps. Throw up some screenies of cpu-z main, memory, spd.
1 - 19 of 19 Posts
Quote:
ok
![]()
Originally Posted by FREELINE57  Are all your ram timmings set? voltage set? Start by dropping your ram freq down a notch and start pushing the cpu freq up 5/10mhz at a time untill it bsod or won't boot then bump up the vcore one notch and boot. Test with prime95 or occt and keep an eye on those temps. Throw up some screenies of cpu-z main, memory, spd. |
2
Quote:
Q9550 is very easy to overclock with P5Q Deluxe.
Try my settings for 4ghz OC
CPU multi: 8.5
FSB: 471
CPU Vcore: 1.2875v
CPU GTL ref (0/2): .67
CPU GTL ref (1/3): .69
CPU PLL: 1.56
FS Termination: 1.26
DRAM volt: depends on your RAM
NB volt: 1.24
NB GTL ref: .65
SB volt: 1.10
PCIE volt: 1.50
LLC: enabled
CPU spectrum: disabled
PCIE spectrum: disabled
Originally Posted by freddy-b hi there I Just switched my Q9400 with a Q9550 And I need some help to get me satrted... b4 i had My Q9400 at 3.6Ghz. and now with the Q9550 it seems Kinda harder to overclock it with my P5Q deluxe..! Could u help me...? thanks in advance, freddy b |
Try my settings for 4ghz OC
CPU multi: 8.5
FSB: 471
CPU Vcore: 1.2875v
CPU GTL ref (0/2): .67
CPU GTL ref (1/3): .69
CPU PLL: 1.56
FS Termination: 1.26
DRAM volt: depends on your RAM
NB volt: 1.24
NB GTL ref: .65
SB volt: 1.10
PCIE volt: 1.50
LLC: enabled
CPU spectrum: disabled
PCIE spectrum: disabled
Quote:
i still cant get it stable,
windows boots up and then when i am in the desktop it Freezes...any help..?
Originally Posted by lockhead Q9550 is very easy to overclock with P5Q Deluxe. Try my settings for 4ghz OC CPU multi: 8.5 FSB: 471 CPU Vcore: 1.2875v CPU GTL ref (0/2): .67 CPU GTL ref (1/3): .69 CPU PLL: 1.56 FS Termination: 1.26 DRAM volt: depends on your RAM NB volt: 1.24 NB GTL ref: .65 SB volt: 1.10 PCIE volt: 1.50 LLC: enabled CPU spectrum: disabled PCIE spectrum: disabled |
windows boots up and then when i am in the desktop it Freezes...any help..?
Quote:
temps were around 23 deegrees idle stock. i use Arctic silver 5...
i dont think it was over heating...
what do u think...?
Originally Posted by ArchCorsair What kind of fan do you have on your TRUE? Maybe its getting too hot. |
i dont think it was over heating...
what do u think...?
Quote:
yeh sure gimmie a minute..
Originally Posted by ArchCorsair Can you post all your settings in bios? |
Sorry about the delay, I had to step out to buy some medicine; I'm sick
![]()
Well to start things off, seems your Vcore is a bit high (what is your goal speed?)
For increased stability you may want to look over this guide to set your GTL per lane:
http://www.overclock.net/intel-mothe...ml#post3167191
Other than that, I'm not sure about your mobo so I can't really say what the voltages should be on the NB & SB.
Hope this helps
Well to start things off, seems your Vcore is a bit high (what is your goal speed?)
For increased stability you may want to look over this guide to set your GTL per lane:
http://www.overclock.net/intel-mothe...ml#post3167191
Other than that, I'm not sure about your mobo so I can't really say what the voltages should be on the NB & SB.
Hope this helps
Quote:
my Goal Speed is 4.0Ghz
Originally Posted by ArchCorsair Sorry about the delay, I had to step out to buy some medicine; I'm sick
Well to start things off, seems your Vcore is a bit high (what is your goal speed?) For increased stability you may want to look over this guide to set your GTL per lane: http://www.overclock.net/intel-mothe...ml#post3167191 Other than that, I'm not sure about your mobo so I can't really say what the voltages should be on the NB & SB. Hope this helps |
2
Quote:
i use intel burn test and Super pi and prime95
Originally Posted by TheBlademaster01 Well, try to either increase the CPU voltage or lower the FSB. You'll have to overclock in small steps, each CPU OC'es different. And what programs do you use for stress testing? |
Quote:
ok, ill try that out, what Vcore should i put and vtt...? please give me a range..
Originally Posted by stevezer Hi it could be your nb voltage try to bump it up, i think 1.3 volts is default , high clock speed with 4 gb of ram , nb will need a maybee 1.4v . freezing in windows could be your memory. hope this helps |
1 - 19 of 19 Posts
