Overclock.net banner

1001 - 1020 of 1212 Posts

·
Premium Member
Joined
·
5,715 Posts

·
Registered
Joined
·
3,156 Posts
without reading through the whole thread, has anyone got 2000IF stable on this board ?
TIA (y)
Yep, 2000 and 2066 stable.

1900 won't boot though and still slowly working on 2100+
 

·
Registered
Joined
·
248 Posts
My Unify-X is on hold until at least until the start of March. :(
That's crazy, cclonline.com where I got mine still have them in stock in the UK, but I'm still waiting for my 5950x from DinoPc. It's been three months now since I placed my order:sleep: absolutely none in the UK at any cost, just ridiculous and frustrating.
 

·
Registered
Joined
·
16 Posts
Why does Unify-X apply DRAM voltage higher than set in BIOS?
1.5 in BIOS -> 1.52 real voltage.
1.48 in BIOS -> 1.5 real voltage.
 

·
Registered
Joined
·
3,156 Posts
Why does Unify-X apply DRAM voltage higher than set in BIOS?
1.5 in BIOS -> 1.52 real voltage.
1.48 in BIOS -> 1.5 real voltage.
Same in unify but by 0.01

1.48 = 1.49
1.5 = 1.51
 

·
Registered
Joined
·
248 Posts
Why does Unify-X apply DRAM voltage higher than set in BIOS?
1.5 in BIOS -> 1.52 real voltage.
1.48 in BIOS -> 1.5 real voltage.
Same in unify but by 0.01

1.48 = 1.49
1.5 = 1.51
Sensors are being misread by some software, surprised RM is too. Go by whatever value DDR voltage is being read in the bios or by hwinfo. I don't think vdimm is being increased but there's no measuring points so can't check which is stupid for an OCers board.
 

·
Registered
Joined
·
391 Posts
Efficiency appears poor with some benchmarks unify x.A10 bios.
Cpu test it holds it own.
Noticed in 7-Zip & PYPrime.
 

·
Registered
Joined
·
139 Posts
Hi guys!

I'm going to buy Unify-X within a few days. Currently running 3900X on CH6 but I want to switch to Unify-X with 5900X. I have some issue deciding what RAM should I buy cause it is super hard to get any decent 2x16 b-die right now. What would you recommend from the following list:
  • F4-4000C16D-32GVK (370e)
  • F4-3600C14D-32GVK (425e)
  • F4-3600C14D-32GTRS (462e)
  • F4-4000C16D-32GTZR (521e)

Up to this date I always preferred Trident variant rather than Ripjaws but prices are crazy right now. I really wanted to get F4-3800C14D-32GTZN or F4-4266C17D-32GTZRB but can't find these anywhere in stock...
 

·
Premium Member
Joined
·
5,715 Posts
I sent you a PM yesterday about the fact that the UNIFY-X is availlable/in stock on Newegg.ca

Shipped and sold by Newegg. I bought one, shipping estimate was next week.
Yeah, saw your PM. Thank you.

But I'm just going to wait for B&H Photo to ship. It would take several days to get a refund, and they say by the end of Feb. :)
 

·
Premium Member
Joined
·
5,715 Posts

·
Registered
Joined
·
633 Posts
Sensors are being misread by some software, surprised RM is too. Go by whatever value DDR voltage is being read in the bios or by hwinfo. I don't think vdimm is being increased but there's no measuring points so can't check which is stupid for an OCers board.
You can try the memory vrm mosfet out reading.
 

·
Registered
Joined
·
30 Posts
Hi guys!

I'm going to buy Unify-X within a few days. Currently running 3900X on CH6 but I want to switch to Unify-X with 5900X. I have some issue deciding what RAM should I buy cause it is super hard to get any decent 2x16 b-die right now. What would you recommend from the following list:
  • F4-4000C16D-32GVK (370e)
  • F4-3600C14D-32GVK (425e)
  • F4-3600C14D-32GTRS (462e)
  • F4-4000C16D-32GTZR (521e)

Up to this date I always preferred Trident variant rather than Ripjaws but prices are crazy right now. I really wanted to get F4-3800C14D-32GTZN or F4-4266C17D-32GTZRB but can't find these anywhere in stock...
I got the 4266 kit, nothing wrong with them, it's the 5900x I have. Had I known I would've tried to search for a better batch. The imc is just limiting, any setting above 1933 and it won't boot and I need to clear cmos again. Makes getting this board redundant,could've got anything and still get to the 1900 if at the same setting no issue.
 

·
Registered
Joined
·
16 Posts
Same in unify but by 0.01

1.48 = 1.49
1.5 = 1.51
Sensors are being misread by some software, surprised RM is too. Go by whatever value DDR voltage is being read in the bios or by hwinfo. I don't think vdimm is being increased but there's no measuring points so can't check which is stupid for an OCers board.
My RAM overclock is stable only on 1.5V (read as 1.51-1.52 in BIOS). That's also an XMP voltage for my kit.
But I am a little afraid to run it 24/7 since Samsung B-Die datasheet specifies 1.5V as an absolute maximum. RAM just can degrade over time if the voltage is really above 1.5V
 

·
Registered
Joined
·
85 Posts
My RAM overclock is stable only on 1.5V (read as 1.51-1.52 in BIOS). That's also an XMP voltage for my kit.
But I am a little afraid to run it 24/7 since Samsung B-Die datasheet specifies 1.5V as an absolute maximum. RAM just can degrade over time if the voltage is really above 1.5V
I have dailied my bdie kit at 1.6V for over a year on my old Zen 2 system and have had 0 signs of degradation on the CPU/RAM side.
Using the same kit now on my 5800X and still no issues whatsoever.
 
1001 - 1020 of 1212 Posts
Top