[IzorkX]

Hey guys.

After my other thread, from your feedback, I decided to buy a new kit.

It's going to be this:

http://www.coolerkit.dk/xspc_rasa_750_rx240_watercooling_kit-p-1750.html

+

http://www.coolerkit.dk/primochill_ice_non_conductive_32_oz____uv_blue-p-1607.html

This will be mounted in a CMII Advanced.

The rad I thought of mounting at the bottom, making space by removing 4 of the HDD bays.

The pump up at the top bays.

Questions:

- Should I use the standard fans or should I buy new ones? If new , which? (See the danish site, and go under "Blæsere")

- I am also thinking of buying new fans for the rest of the case, which ones is good for this purpose? (1x 140mm, 3x 120mm is needed here)

What do you think of this setup?

 

[IzorkX]

Something like this:

 

[X-Nine]

Negative ghost rider. Pump need to be below the reservoir. Always. Forever. Go with the XSPC kit over the Primochill kit.

 

[IzorkX]

Quote:

Originally Posted by XNine;12995513
Negative ghost rider. Pump need to be below the reservoir. Always. Forever. Go with the XSPC kit over the Primochill kit.

What?

The primochill is just the liquid :/

And the pump is both pump / res.

 

[JedixJarf]

Lol that setup is fine, pump / res combo, make sure it goes from pump to rad then cpu

 

[JedixJarf]

And no, dont get that dyed junk, it will gunk up your blocks, just get distilled water + silver kill coil and some colored tubing.

 

[X-Nine]

Quote:

Originally Posted by IzorkX;12995536
What?

The primochill is just the liquid :/

And the pump is both pump / res.

And that's why you drink coffee before posting. Question, why get primochill fluid and not just run distilled water/nuke/kill coil? Oh, and get better tubing for your kit. The Rasa tubing is garbage.

 

[IzorkX]

Thanks for the feedback.

http://www.coolerkit.dk/feser_one_cooling_fluid___1l___ultra_pure_water-p-740.html

+

http://www.coolerkit.dk/d_tek_super_cool___120_ml-p-1443.html

And what tubes that is coloured? I can't seem to find any that fits the ones that is incl in the kit.

 

[rubix_1011]

Loop order doesn't matter; especially for a pump/res combo. Loop water temps will be within 2-3C at any single point in the loop, including before/after rad.

http://www.xtremesystems.org/forums/showthread.php?t=225485

The only place where loop order does matter is with a separate pump and res; you'd like to have the res higher than the pump and feeding the inlet to prevent air entering the pump. You can deviate from this order and still have a successful loop anyway...it's just strongly suggested to make filling the loop and bleeding air easier.

 

[JedixJarf]

Quote:

Originally Posted by IzorkX;12995672
Thanks for the feedback.

http://www.coolerkit.dk/feser_one_cooling_fluid___1l___ultra_pure_water-p-740.html

+

http://www.coolerkit.dk/d_tek_super_cool___120_ml-p-1443.html

And what tubes that is coloured? I can't seem to find any that fits the ones that is incl in the kit.

http://www.coolerkit.dk/slanger_10mm__3_8__id-c-370_140_144.html

http://www.coolerkit.dk/slanger_12mm__%C2%BD__id-c-370_140_146.html

Just make sure you use the clamps that come with the kit.

 

[IzorkX]

Quote:

Originally Posted by rubix_1011;12995702
Loop order doesn't matter; especially for a pump/res combo. Loop water temps will be within 2-3C at any single point in the loop, including before/after rad.

The only place where loop order does matter is with a separate pump and res; you'd like to have the res higher than the pump and feeding the inlet to prevent air entering the pump. You can deviate from this order and still have a successful loop anyway...it's just strongly suggested to make filling the loop and bleeding air easier.

Ah... Well I will only cool CPU atm so no problem then.

 

[IzorkX]

Quote:

Originally Posted by JedixJarf;12995715
http://www.coolerkit.dk/slanger_10mm__3_8__id-c-370_140_144.html

http://www.coolerkit.dk/slanger_12mm__%C2%BD__id-c-370_140_146.html

Just make sure you use the clamps that come with the kit.

Ah ok, thanks.

I will go for these then http://www.coolerkit.dk/feser_tube___12_7_9_65mm___3_8___10mm____uv_lysebl%C3%A5-p-1463.html

 

[X-Nine]

Quote:

Originally Posted by IzorkX;12995734
Ah ok, thanks.

I will go for these then http://www.coolerkit.dk/feser_tube___12_7_9_65mm___3_8___10mm____uv_lysebl%C3%A5-p-1463.html

Doesn't sound like a bad idea. You can use color dyes, if that's what you want, but it's recommended by pretty much everyone to just do colored tubing instead to limit the gunk buildup and staining dyes cause on your blocks and such.

Good luck and let us know how it turns out.

 

[IzorkX]

The price for the kit is very expensive in denmark..

350 bucks.. you can get it for 200