Overclock.net banner

1 - 3 of 3 Posts

·
Registered
Joined
·
2 Posts
Discussion Starter #1
Hey folks,

Back again, i figured out what was wrong with my rig not being able to post the OC settings i had. i didnt give it enough juice...

Well not only was i wrong about that but i cant get my ram (TW3X4G1600C9DHX) to be able to boot at 1600mhz with FSB 400x7.5

Does anyone have the same or very similar components where they got their ram running at 1600mhz timings (9-9-9-24 1.8v or better)? i know that corsair posted a sticky regarding this model not always being able to work with P45's but I was wondering if anyone had figured a workaround.

The best settings ive gotten so far: (one core stopped at Prime95)

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .............: [ Auto ]
CPU Clock Ratio .....................: 7 X
Fine CPU Clock Ratio.................: .5
CPU Frequency .......................: 3.37GHZ (450x7.5)

Clock Chip Control
Standard Clock Control
CPU Host Clock Control...............: [ Enabled ]
CPU Host Frequency (Mhz) ............: 450
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .............................: [ Disabled ]

Advanced Clock Control [Press Enter]
CPU Clock Drive......................: [ 800 mV ]
PCI Express Clock Drive..............: [ 900mV ]
CPU Clock Skew (ps)..................: [ 0ps ]
MCH Clock Skew (ps)..................: [ 0ps ]

DRAM Performance Control
Performance Enhance..................: [ STANDARD ]
(G)MCH Frequency Latch...............: [ AUTO ]
System Memory Multiplier ............: 3.33D
Memory Frequency (Mhz) ..............: 1500
DRAM Timing Selectable ..............: [ Manual ]

Standard Timing Control
CAS Latency Time.....................: 10
tRCD ................................: 10
tRP'.................................: 10
tRAS.................................: 20

Advanced Timing Control
tRRD.................................: 5
tWTR.................................: 5
tWR..................................: 10
tRFC.................................: 70
tRTP.................................: 5
Command Rate (CMD) ..................: 2

Channel A
Static tRead Value...................: 8
tRD Phase0 Adjustment................: 0 [ AUTO ]
tRD Phase1 Adjustment................: 0 [ AUTO ]
tRD Phase2 Adjustment ...............: 0 [ AUTO ]
tRD Phase3 Adjustment................: 0 [ AUTO ]
Trd2rd(Different Rank)...............: 9 [ AUTO ]
Twr2wr(Different Rank)...............: 7 [ AUTO ]
Twr2rd(Different Rank)...............: 8 [ AUTO ]
Trd2wr(Same/Diff Rank)...............: 8 [ AUTO ]

Channel B
Static tRead Value...................: 8
tRD Phase0 Adjustment................: 0 [ AUTO ]
tRD Phase1 Adjustment................: 0 [ AUTO ]
tRD Phase2 Adjustment ...............: 0 [ AUTO ]
tRD Phase3 Adjustment................: 0 [ AUTO ]
Trd2rd(Different Rank)...............: 9 [ AUTO ]
Twr2wr(Different Rank)...............: 7 [ AUTO ]
Twr2rd(Different Rank)...............: 8 [ AUTO ]
Trd2wr(Same/Diff Rank)...............: 8 [ AUTO ]

Motherboard Voltage Control
Voltage Type...............
CPU
CPU Vcore............................: 1.25625V
CPU Termination….....................: 1.220V
CPU PLL..............................: 1.570V
CPU Referen..........................: 0.760V [ AUTO ]

MCH/ICH
MCH Core.............................: 1.240V
MCH Reference........................: 0.760V [ AUTO ]
MCH/DRAM Ref.........................: 0.750V [ AUTO ]
ICH I/O......................….......: 1.570V

DRAM
DRAM Voltage ........................: 1.800V
DRAM Termination ....................: 0.750V [ AUTO ]
Ch-A DATA VRef.......................: 0.750V [ AUTO ]
Ch-B DATA VRef.......................: 0.750V [ AUTO ]
Ch-A Address VRef....................: 0.750V [ AUTO ]
Ch-B Address VRef....................: 0.750V [ AUTO ]

Advanced Settings
Limit CPUID Max. to 3...............: [ DISABLED ]
No-Execute Memory Protect...........: [ ENABLED ]
Load-Line Calibration...............: [ DISABLED ]
CPU Enhanced Halt (C1E).............: [ DISABLED ]
CPU Thermal Monitor 2(TM2) .........: [ ENABLED ]
CPU EIST Function...................: [ DISABLED ]
Virtualization Technology...........: [ ENABLED ]

settings taken from (http://forums.tweaktown.com/f69/ga-e...so-good-32738/)
 

·
Registered
Joined
·
2 Posts
Discussion Starter #3
i actually do need some help. i cant get my ram to run at 1600, without my PC crashing or rebooting thats why i tried setting it to 1500, which turned out to be unstable still but i got to load to windows.

Default bios
Q9300 - 2.5ghz (333x7.5)
DDR3 - 1066 ( 7 7 7 20 )

What i want to clock:
Q9300 - 3.00ghz (400x7.5)
DDR3 - 1600 ( 9 9 9 24 )

at the top of the page, those are what i set my voltages and timings, can you or anyone else recommend what i should adjust to make it run to what i want to OC at?
 
1 - 3 of 3 Posts
Top