Overclock.net banner
Cancel
Create thread New Forums

[Official] NVIDIA RTX 5090 Owner's Club

Tags
5090 blackwell nvidia rtx
44 reading
Jump to Latest
7,001 - 7,020 of 18,210 Posts
#7,001 ·
bmagnien said:
@Alacrity30 great PR score. Have you tried running +3000 mem? Saw your top time had mem clocks below that, might be enough to bump you to top 10.

What card are you running, and are you achieving 45c just with ambient and full fans?
Click to expand...
Thanks, depends which benchmark you’re referring to but I pretty much run all of them at +3000 mem now since I seem to be able to complete most if not all tests with that.

TUF OC

Putting PC near open door during 10c ambient temps so usually not running full GPU fans. Not sure if bro science but I seem to get higher scores whenever I turn the fans down a bit. My Steel Nomad PR was both fans locked at 40% and case and cpu fan at 100. Longer tests I try to run them at 70ish but I have some high scores with 100% fans as well so who knows could just be run to run variance.
 
#7,002 ·
consume1234 said:
I didn't think it was possible to buy video cards from b&h. Congrats.
Click to expand...
They started sending out the emails a few weeks back, send you a link and you have 24 hours to purchase a card. I have had 4 or 4 offers already, turned them down. 2400-2700 for a 5090 and 1450 for a Asus Tuf 5080. Today I got an offer for a 5080 PNY, thinking about it.
 
  • Helpful
Reactions: iamjanco
Save
Reply Quote Rep+ Rep+
#7,003 ·
tps3443 said:
I scored 14,725 in Nomad DX12, and 14,500 in Speedway.

These seem reasonable? I’m using PCIe Gen 3.0, Rebar is disabled.
Click to expand...
Sounds fine if you're at stock. PCI-E 3.0 is because Mobo/CPU? Even then for those 2 specific benchmarks, PCI-E gen shouldn't affect the scores too much.
 
  • Rep+
Reactions: Papusan
Save
Reply Quote Rep+ Rep+
#7,005 ·
cta62 said:
Did anyone gain a large amount of overclocking headroom with this new driver? I went from +210 on the core to +330 on the core. Is it because the voltage slider works now and I have it at +100? Last driver I used was 572.47 and the voltage slider was bugged.
Click to expand...
What voltage you got right now ? My astral after the new driver with +280 on the core is constantly hitting 1.1-1.12……
 
#7,006 ·
Just got a 5090 Astral and trying to push some PR runs but my score are stuck around at 40350-40400……. I try to do+280 on core and 5000+on ram any higher than it crashe. I think that is it HHHH without some force Air cooling mod just set ALL fan to 100%…….
 
#7,007 · (Edited)
guixianglun said:
Just got a 5090 Astral and trying to push some PR runs but my score are stuck around at 40350-40400……. I try to do+280 on core and 5000+on ram any higher than it crashe. I think that is it HHHH without some force Air cooling mod just set ALL fan to 100%…….
Click to expand...
That's about right, comparable to my TUF OC at almost same settings. Try the new driver and push your core to +400, should be able to get 40700 to 40800.

Also, 1.1+ V sounds high for PR. Try leaving voltage offset at default 0. Pretty sure I get better scores just leaving this alone.
 
#7,008 ·
Sky3900 said:
That's about right, comparable to my TUF OC at almost same settings. Try the new driver and push your core to +400, should be able to get 40700 to 40800.

Also, 1.1+ V sounds high for PR. Try leaving voltage offset at default 0. Pretty sure I get better scores just leaving this alone.
Click to expand...
What software are you using ? Afterburner or GPU tweak ? I have a TUF OC too on my other system too but it max out PR at 40100-40150 the V core seems like get locked at 1.06V…… not like the astral i got can push to 1.12V. I also tried to flash the Astral bios in to tuf oc no luck…..Is this just bios different or the astral really have better chips ?
 
#7,009 ·
guixianglun said:
What software are you using ? Afterburner or GPU tweak ? I have a TUF OC too on my other system too but it max out PR at 40100-40150 the V core seems like get locked at 1.06V…… not like the astral i got can push to 1.12V. I also tried to flash the Astral bios in to tuf oc no luck…..Is this just bios different or the astral really have better chips ?
Click to expand...
GPU Tweak, my v-core runs about the same 1.045 to 1.06ish max in PR... No clue if Asus is binning better chips for the Astral. Could also be system optimization. I make sure to halt all unnecessary processes, case/GPU fans @ 90%, rbar on (rdr2 settings), vsync force off, texture quality max performance, hdr off, 1080p, limited 8-bit color, all osd displays off, stand alone 3D mark version.
 
#7,010 ·
Try out "GTA V Enhanced Edition" in 4K DLSS4 DLAA Transformer Model Preset K, enable RTX HDR and set <RTIndirectDiffuse_SecondBounce_Enabled value="true" /> in the game's settings.xml file.

Visit Michael's house in Rockford Hills, the "De Santa Residence," and walk around in its living room, go upstairs - just stroll around and explore the house.

Then, post your GPU Power Consumption :)
 
#7,013 ·
HoBahr said:
Amazing Temps for AirCooled !
Click to expand...
Fans at 80% on the GPU and 100% on my case. But I only ran it for a few seconds to see if it would crash at such a high core clock.
If I run the full benchmark, it will probably go over 60 degrees even with the fans at 100%. But this 5090, with a hardmod, block, and custom water cooling, shows a lot of potential. I’m not sure if I’ll finally decide to put it under water, but things are looking promising.
 
#7,014 ·
Mystic33 said:
Fans at 80% on the GPU and 100% on my case. But I only ran it for a few seconds to see if it would crash at such a high core clock.
If I run the full benchmark, it will probably go over 60 degrees even with the fans at 100%. But this 5090, with a hardmod, block, and custom water cooling, shows a lot of potential. I’m not sure if I’ll finally decide to put it under water, but things are looking promising.
Click to expand...
I think it'll be great under water
 
#7,015 ·
I got around to trying to launch my own Zotaс
Technology Computer hardware Packaging and labeling Electronics Video Game Software

unfortunately it was unsuccessful (nothing has burned yet ha ha) all the ROP`s are in place

the card didn't fit into the case because the tops of the pumps prevented it from being inserted into the case
Sorry you have to see all this dust and dirt) Kitchen renovation helped my computer look like this
Electronic device Electrical cable Electronics Technology Computer hardware

Electronic device Electrical cable Electrical wiring Technology Wire
I decided to try using my old raiser v 4 and some materials at hand:D
Electronic device Computer hardware Technology Electronics Machine

in general the video card works in x4 mode
2.0\.3.0\ 5.0

I didn't do any benches with this mode, so I launched Furmark for about 3 minutes and then just turned it off - it was scary, so I also turned on the thermal camera

Red Orange Neon Night Visual Effect Lighting

White Text Font Screenshot

yes i used the old cable mod cable for corsair ax1600i
now i need to do everything new including replacing the power supply
as well as general cleaning and moving the pump tops to another place

I thought I could do it quickly, but this is what I managed to achieve before going back to work))
sorry for the mess
Electronic device Computer hardware Technology Electrical cable Peripheral

Electronic device Electronics Gadget Electrical cable Technology

I hope you had fun
my wife wasn't very happy when she saw this in the morning
 
Save
Reply Quote Rep+ Rep+
#7,016 ·
Here is a question - related to working out what shunt value one should stack for the RTX 5090
Here are all the pieces of the puzzle.
the card's bios is set to 600w
power through the 12pin, when under max load, is 600w
when using the shutmod calculator it assumes the PCI power counts to the cards power limit. Does it? Does the bios power limit only look at slot power?

Having the slot power factored in (or not) is very impactful to working out the new shut. (Maybe? or is 650w vs 750w minor? maybe some other limit would stop the card from pulling that much power? ignoring transient power spikes - as those already hit 800w on my unmod'd Astral.)
Text Screenshot Font Number Software
Text Font Screenshot Number Computer program


(and if it doesn't factor in the PCI then doing a paintmod works as that is kinda equal to 15ohm (and going by the 0 pci power calculation, that is a boost of 80w to 12pin (or loss if total card power includes the pci.)
shrug

TLDR, should one factor in the PCI power when looking at BIOS limits? And, if no, should the value for the shuntmod calculator be 0 for Slot limit?
 
#7,017 ·
Zurv said:
Here is a question - related to working out what shunt value one should stack for the RTX 5090
Here are all the pieces of the puzzle.
the card's bios is set to 600w
power through the 12pin, when under max load, is 600w
when using the shutmod calculator it assumes the PCI power counts to the cards power limit. Does it? Does the bios power limit only look at slot power?

Having the slot power factored in (or not) is very impactful to working out the new shut. (Maybe? or is 650w vs 750w minor? maybe some other limit would stop the card from pulling that much power? ignoring transient power spikes - as those already hit 800w on my unmod'd Astral.)
View attachment 2703362 View attachment 2703363

(and if it doesn't factor in the PCI then doing a paintmod works as that is kinda equal to 15ohm (and going by the 0 pci power calculation, that is a boost of 80w to 12pin (or loss if total card power includes the pci.)
shrug

TLDR, should one factor in the PCI power when looking at BIOS limits? And, if no, should the value for the shuntmod calculator be 0 for Slot limit?
Click to expand...
Based on my tests on the 5090, it seems it uses max 11-12W from the slot, so you could add that to the shunt calculation.

If it's needed, probably not but maybe to discard balancing issues you could do it. It will go from 11-12W to like 13-13.5W.
 
Save
Reply Quote Rep+ Rep+
#7,018 ·
What are the advantages of an AIO card versus an aftermarket air-cooled version?

How big of a difference will there be in terms of temperature and overclocking?

I saw a review by Hardware Unboxed wherein changing the BIOS from Silent to Gaming and increasing the fan RPM from ~1200 to ~1600 reduced temperature from 77c to 67c in the The Last of Us Part I. Since I don’t mind running the fan at high RPMs during gaming, I was wondering whether the non-liquid version will overclock just as well with a more aggressive fan curve. Correct me if I’m wrong though, because I don’t want to regret my decision later on.

My local store got a new shipment of 5090s, but they only have the Suprim SOC but not the Suprim Liquid SOC. Hence the immediate concern as to whether I should just snag one while they’re still available.

Any advice would be greatly appreciated. Thank you!
 
Save
Reply Quote Rep+ Rep+
#7,019 ·
ahnafakeef said:
How big of a difference will there be in terms of temperature and overclocking?
Click to expand...
If you are Looking for Binning or OC potential its absolute Silicon Lottery

My Inno3D X3 Non OC makes 3,3GHZ with Xtreme WF WB Bios and this is one of the Cheap MSRP Cards and got very Lucky
 
#7,020 ·
ahnafakeef said:
What are the advantages of an AIO card versus an aftermarket air-cooled version?

How big of a difference will there be in terms of temperature and overclocking?
Click to expand...
Image


Image
 
  • Rep+
Reactions: ahnafakeef
Save
Reply Quote Rep+ Rep+
7,001 - 7,020 of 18,210 Posts
About this Discussion
18K Replies
579 Participants
Last post:
synergon
Overclock.net
posts
28M
members
562K
Since
2004
The premier forum for overclocking experts and enthusiasts. Discuss hardware optimization, custom builds, benchmarking, cooling solutions, and pushing the boundaries of computing performance. From beginner guides to extreme overclocking, join our technical community to master system tuning.
Full Forum Listing
Explore Our Forums
Intel CPUs Hardware News NVIDIA PC Gaming Water Cooling